Lincoln Electric IM613-B manual 1TROUBLESHOOTINGE-1, HOW to USE Troubleshooting Guide

Page 35

E-1TROUBLESHOOTINGE-1

HOW TO USE TROUBLESHOOTING GUIDE

WARNING

Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel. Unauthorized repairs performed on this equipment may result in danger to the technician and machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical Shock, please observe all safety notes and precautions detailed throughout this manual.

__________________________________________________________________________

This Troubleshooting Guide is provided to help you locate and repair possible machine malfunctions. Simply follow the three-step procedure listed below.

Step 1. LOCATE PROBLEM (SYMPTOM).

Look under the column labeled “PROBLEM (SYMPTOMS)”. This column describes possible symptoms that the machine may exhibit. Find the listing that best describes the symptom that the machine is exhibiting.

Step 2. POSSIBLE CAUSE.

The second column labeled “POSSIBLE CAUSE” lists the obvious external possibili- ties that may contribute to the machine symptom.

Step 3. RECOMMENDED COURSE OF ACTION

This column provides a course of action for the Possible Cause, generally it states to contact you local Lincoln Authorized Field Service Facility.

If you do not understand or are unable to perform the Recommended Course of Action safely, contact you local Lincoln Authorized Field Service Facility.

WARNING

ELECTRIC SHOCK can kill.

•Do not touch electrically live parts such as output terminals or internal wiring.

•When inching with gun trigger, electrode and drive mechanism are “hot” to work and ground and could remain energized several seconds after the gun trigger is released.

•Turn OFF input power at welding power source before installation or changing drive roll and/or guide tubes.

•Welding power source must be connected to system ground per the National Electrical Code or any applicable local codes.

•Only qualified personnel should perform these trouble shooting procedures.

Observe all additional Safety Guidelines detailed throughout this manual.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER FEED 11

Page 34 Page 36
Image 35
Page 34 Page 36
Contents IM613-B Safety Depends on YouSafety Electric Shock can kill Iii SafetySûreté Pour Soudage a L’Arc Précautions DE SûretéThank You Table of Contents P315 Series Section ESection F Power Feed InstallationOn the Floor Safety PrecautionWire Feeder to Power Source Configurations HangingCable Connections Current Wire Drive Gear Ratio High or LOW SpeedChanging the Wire Drive Ratio Work Cable Connections Selecting the Proper Gear RatioRatio Change Procedure Setting DIP Switches in the Control BOX DIP Switch SetupFigure A.4 Setting DIP Switches in the Wire DriveFAST-MATEGUN Adapter Guide Tubes Procedure to Install Drive Rolls and Guide TubesDrive Roll KIT and Guide Tube Installation General Guidelines GUN and Cable AssembliesMagnum Guns GUN Connection GuidelinesBuildup of Shielding GAS may harm health or kill Gmaw Shielding GASLifting Handle Cylinder may explode if damagedOptional Panels for Control BOX General Panel Installation GuidelinesOperation K1542-11 MX2 PanelOptional Control Box Panels Lower PanelsK1542-4 CV/Gouge PanelStd K1542-12 MSP2 Panel Optional K1640-1 Dual Procedure / Memory Door Panel OptionalControl BOX -- PC Board Adjustments Control BOX Panels -- SET UP Controls DescriptionControl BOX -- Setting Operating Limits Control BOX -- Using Operating LimitsCold Feed / GAS Purge Switch Wire Drive OperationWire Drive Settings -- External STEP/4 Step SwitchGear BOX Ratio Wire Reel Loading READI-REELS, Spools or CoilsWire Drive -- PC Board Adjustments Electrode PolarityDrive Roll Pressure Setting Feeding Electrode and Brake AdjustmentGAS Guard Regulator Setting Making a Weld Wire Reel ChangingWire Feed Overload Protection Status Light States Component Status LightsStatus Light States CON’T Cored Electrode AccessoriesWire Size Roll Drive Driven Solid Steel Electrode Table C.1 Drive Roll and Guide Tube KitsK1543, K1544 and K1545 Input Cable Assemblies General Panel Installation GuidelinesDescription of Optional CON- Trol BOX Panels K1649-1 Mounting Bracket Horizontal Wire Spindle AdaptersK1536-1 Water Flow Sensor KIT K659-1 GAS Guard RegulatorGun and Cable Maintenance MaintenanceMaintenance Wire Drive Motor and GearboxHOW to USE Troubleshooting Guide 1TROUBLESHOOTINGE-1Troubleshooting Your local Lincoln Authorized Possible Cause Recommended Symptoms Course of ActionField Service Facility Troubleshooting Course of Action Possible CauseEither of these fail, the problem is Change Or harness disconnected from Fails the continuity test, repair or Possible Cause Err 005 Err 001Err 003 Err 004Err 201 Err 020Err 100 Err 200Err 212 Err 211Wiring Diagram Power Feed 11 Wire Feeder Wiring Diagram DiagramsL10834 Power Feed $700.00 Basic CoursePrecaucion Warnung
Top Page Image Contents