Skil 3310 manual Removal and Installation Blade, Using the Correct Blade

Page 34

SM 2610008289 02-10:3310 Table Saw 2/2/10 8:38 AM Page 34

Adjustments

Removal and Installation

of the Blade

!WARNING performing any assembly, adjustment or repair to avoid possible injury.Disconnect plug from power source before

Using the Correct Blade

IMPORTANT: The saw blade provided on this tool has a carbide-tipped kerf width of .128” and a plate (body) thickness that is .086” thick. When looking for a replacement blade, select one with dimensions close to the original blade. This information

FIG. 13

.090Ó

MUST BE .092Ó OR MORE

DOIT Ê'e6TRE DE 0,092 po OU PLUS DEBE SER 0.092 PULGADAS O MÁ'e7S

RIVING KNIFE

COUTEAU DIVISEUR

CUCHILLA SEPARADORA

KERF WIDTH

LARGEUR DE VOIE

ANCHURA DE LA SECCIîN DE CORTE

BLADE TEETH

DENTS DE LA SCIE

DIENTES DE LA HOJA

may not be printed on the blades packaging. If not, check the manufacturers catalog or website. Skil offers an extensive line of Premium-Quality Professional Saw Blades that match the requirements for this tool. You must select a blade with a kerf width of .092” or more and a plate (body) thickness .088” or less (Fig. 13).

To reduce the risk of injury, do not use ! WARNING extra thin kerf saw blades. The kerf of the

blade must be wider than .092”. Extra thin kerf saw blades (less than .092”) may cause the work piece to bind against the riving knife during cutting. It is recommended that the kerf of the replacement blade used on this saw be .092” or more.

To reduce the risk of injury, do not use ! WARNING saw blades made with a thick body plate. If

the replacement saw blade's plate thickness is greater than

.088”, the riving knife would not properly serve as an aid to reduce kickback. The replacement blade's plate thickness must be less than .088”.

To reduce the risk of injury, do not use

!WARNING blade “dampeners,” “stabilizers,” or “stiffening collars” on both sides of a replacement blade. These are metal plates positioned against the sides of the blade to reduce deflection that may occur when using thin saw blades. Use of these devices on both sides will prevent the blade from being properly aligned with the riving knife, which may bind the work piece during cutting. One “stabilizer” plate may be placed only against the outside of a thin replacement blade. These plates are not required with the supplied Skil blade.

Changing the Blade

NOTE: Clean blade of any excess oil before installation.

1.Remove the table insert 1 (Fig. 14).

2.Raise the blade 2 to the maximum height by turning the control wheel 3 counterclockwise (Fig. 14).

3.Remove the arbor nut 4 and flange 5 (Fig. 15).

4.Clean any sawdust from both blade collars before installing the blade. Install a 10" (25.4 cm) blade. Install the saw blade onto the arbor with the blade teeth pointing toward the front of the saw.

To avoid injury, do not use a blade larger or smaller than 10" diameter and 5/8" arbor.

5.Install the flange 5 against the blade 2 and thread the arbor nut 4 as far as possible by hand. Ensure that the blade is flush against the inner blade flange 6 (Fig. 15).

MUST BE LESS THAN .088Ó

 

 

 

BLADE BODY PLATE

 

 

DOIT Ê'e6TRE DE MOINS DE 0,088 po

 

 

 

PLAQUE DU CORPS DE LA LAME

DEBE SER MENOS DE 0.088 PULGADAS

 

 

 

PLACA DEL CUERPO DE LA HOJA

2

1

FIG. 14

3

2

FIG. 15

 

5

4

6

34.

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Importante Work Area General Safety RulesPersonal Safety Tool UseAdditional Safety Rules Tool CareKnow Your Cutting Tools Think Safety Commencing power tool operationWhen SERVICING, USE only Identical REPLACE- Ment Parts Motor Specifications and Electrical RequirementsGeneral Specifications Double Insulated ToolsTable of Contents Tools Needed For Assembly Glossary of TermsSécurité de l’utilisateur Consignes générales de sécuritéZone de travail Utilisation de l’outilConsignes de sécurité supplémentaires Entretien de l’outilFAMILIARISEZ-VOUS Avec VOS Outils DE Coupe LA Sécurité Avant Tout Pour Assurer SA SécuritéRallonges Spécifications du moteur et spécifications électriquesSpécifications générales Outils à double isolementTable des matières Guide de diagnosticLexique Lexique Outils nécessaires à l’assemblageSeguridad personal Normas generales de seguridadArea de trabajo Utilización de la herramientaNormas de seguridad adicionales Cuidado de la herramientaConozca SUS Herramientas DE Corte Piense EN LA Seguridad Suficiente para causar lesiones gravesCordones de extensión Especificaciones del motor y requisitos eléctricosEspecificaciones generales Herramientas con aislamiento dobleIndice Localización y reparación de averíasGlosario de términos Herramientas necesarias para el ensamblajeThis page intentionally left blank Getting To Know Your Table Saw 12a12bFamiliarisez-vous avec Votre scie de table Familiarización con la sierra De mesaTable Insert 17 cSmart Guard System Miter GaugeGuide DE Coupe Angulaire Système Smart Guard16. Élément Amovible DE LA Table DE Coupe Sistema DE Protector Inteligente Smart GuardUnpacking and Checking Contents Temps de montage Ouverture de l’emballage et Vérification du contenuDesempaquetado y Piezas sueltas en la cartónAdjusting the 90 Stop Adjustments45 Positive Stops Adjustment Adjusting the 45 StopRéglage des butées positives 90 et RéglagesAjustesAjuste de los topes positivos De 90 y Plug from power source before mak ngi any Blade Parallel to Miter Gauge Groove AdjustmentProtect your hands Réglages De la lame afin de protéger vos mainsUsing the Correct Blade Removal and Installation BladeTo reduce the risk of injury, do not use Changing the Blade Utiliser la lame correcte Retrait et installation de la lameRemoción e instalación de la hoja Utilización de la hoja correctaUsing Carbide-Tipped Blades Utilisation de lames à pointes Au carbure Utilización de hojas con punta de carburoMiter Gauge Adjustment Manual Pointer AdjustmentAligning Rip Fence Ajustes Attaching the Smart Guard System Positioning the Riving KnifePositionnement DU Couteau Diviseur AssemblageEnsamblajeMontage du système Smart Guard Posicionamiento DE LA Cuchilla SeparadoraAttaching the Guard Assembly Attaching the ANTI-KICKBACK DeviceInstalación DEL Ensamblaje DEL Protector Montage DE Lensemble DE Barrière DE SécuritéInstalación DEL Dispositivo Antirretroceso Assembling the Leg Stand AssemblyAttaching Rip Fence Mounting the Table Saw To the Leg StandAssemblage EnsamblajeMounting Table Saw Mounting to PlywoodInstallation de la scie De table Montaje de la sierra de MesaOn/Off Switch with Safety Key Keeping the Area CleanBasic Table Saw Operation Mantenga limpia el área Funcionamiento básico de la Sierra de mesaMaintien de la propreté De la zone de travail Interrupteur marche/arrêt Avec clé de sécurité❷ Main Barrier Guard Component Parts figure❶ Riving Knife ❸ Anti-Kickback DeviceComposants Figure Système Smart GuardSistema de protector inteligente Smart Guard Piezas componentes figuraSee page 40 for detailed instructions Attachment/RemovalSystem Storage Rangement du système Montage/démontageInstalación/desinstalación Almacenamiento del sistemaUsing the Miter Gauge with T Bar Calibre DE Ingletes Avec la barre en « T »Otra Razon Auxiliary Fence Push Stick and Push BlockWorkpiece Guide de coupe auxiliaire Tope-guía auxiliarCrosscutting Corte transversal Coupe transversaleCoupe à répétition Corte repetitivoMiter Cutting Fence / Work SUPPORT, Push Stick or Push BlockCoupe angulaire biseautée Coupe angulaireCoupe transversale biseautée Utilisation du guide de refenteRipping Bevel RippingCoupe EN Long Biseautée Coupe en longCorte al hilo Corte AL Hilo EN BiselResawing Making a FeatherboardCómo hacer una tabla con Canto biselado Coupe de dédoublementFabrication d’une planche à Languettes Reaserrado Soires DE Sciage »Rabbeting Install Blade Guard Immediately Upon COMNon Thru-Sawing Pletion of Rabbeting OperationAserrado no pasante Coupe partielleRéalisation de feuillures Corte de rebajosDado and Molding Cutting Installing a Dado SETUsing Stacked Dado Sets Is not designed to accept larger sized dadosPage Adjustable or Wobble Dado Sets Returning SAW to Normal THRU-CUTTINGJuegos DE Mortajar Ajustables U Oscilantes Regreso DE LA Sierra a Corte Pasante NormalEnsembles DE Lames a Rainurer Reglables OU Oscillantes Maintaining Your Table Saw MaintenanceSpecial Cutting Techniques Entretien Entretien de la Scie de tableMantenimiento de la Sierra de mesa Técnicas de corte especialesLubrication Blade Elevation and Tilting MechanismCare of Blades Lubricación LubrificationEntretien des lames Cuidado de las hojasTrouble Shooting Guide de diagnosticLocalización y reparación De averías Averia LA Sierra no ArrancaSM 2610008289 02-103310 Table Saw 2/2/10 839 AM SM 2610008289 02-103310 Table Saw 2/2/10 839 AM 2610008289 02/10
Top Page Image Contents