Skil 3310 manual Attachment/Removal, See page 40 for detailed instructions, System Storage

Page 52

SM 2610008289 02-10:3310 Table Saw 2/2/10 8:38 AM Page 52

Attachment/Removal

(see page 40 for detailed instructions)

The three primary components of the Smart Guard blade guarding system are designed for rapid attachment, adjustment, and/or removal without the need for additional tools.

The Main Barrier Guard component can be quickly attached and detached through the use of a quick release lever. The guard is attached by seating the crossbar into the top of the Riving Knife and engaging the locking lever. Following this process in reverse, the guard can be easily removed for special operations such as dados or rabbets.

The Anti-Kickback Device can be easily attached by aligning the attachment pin with the hole in the rear of the riving knife. It can be easily removed by depressing the compression pads on either side of the Anti-Kickback Device and lifting it away.

The Riving Knife can be easily adjusted to one of three heights by removing the table insert, raising the blade to its full height and releasing the riving knife release lever at the base of the Riving Knife. The Riving Knife should be locked in its highest position for use with the Main Barrier Guard and Anti-Kickback Device. It can be adjusted to its middle position for non-through cuts and for use as a material splitter without the Main Barrier Guard and Anti-Kickback Device.

In the event that the Riving Knife can not be used for a specific cut, it can be adjusted to its lowest position, thus placing it 1” above the surface of the table (while the blade is at its full height).

System Storage

When not in use, the Main Barrier Guard and Anti-Kickback Device can be stored under the left side of the table.

Use of all the components of the Smart Guard ! WARNING System, including Main Barrier Guard, Anti-

Kickback Device, and Riving Knife is highly recommended to provide protection against accidents and injury.

1. Turn the Main Barrier Guard assembly 1 upside down and slide it into the U-bracket 2 at the rear left side of the saw (Fig. 33).

2. Pivot the rear of the guard up and into the front mounting bracket 3.

3. Lock the Main Barrier Guard assembly into place in the same manner as you would attach it to the Riving Knife (Fig. 33).

4. Slide the pawls of the Anti-Kickback Device 4 into the two slots and attach to bracket in the same manner that it attaches to the Riving Knife.

1

3

4

 

 

FIG. 33

2

52.

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Importante General Safety Rules Personal SafetyWork Area Tool UseAdditional Safety Rules Tool CareKnow Your Cutting Tools Think Safety Commencing power tool operationMotor Specifications and Electrical Requirements General SpecificationsWhen SERVICING, USE only Identical REPLACE- Ment Parts Double Insulated ToolsTable of Contents Tools Needed For Assembly Glossary of TermsConsignes générales de sécurité Zone de travailSécurité de l’utilisateur Utilisation de l’outilConsignes de sécurité supplémentaires Entretien de l’outilFAMILIARISEZ-VOUS Avec VOS Outils DE Coupe LA Sécurité Avant Tout Pour Assurer SA SécuritéSpécifications du moteur et spécifications électriques Spécifications généralesRallonges Outils à double isolementTable des matières Guide de diagnosticLexique Lexique Outils nécessaires à l’assemblageNormas generales de seguridad Area de trabajoSeguridad personal Utilización de la herramientaNormas de seguridad adicionales Cuidado de la herramientaConozca SUS Herramientas DE Corte Piense EN LA Seguridad Suficiente para causar lesiones gravesEspecificaciones del motor y requisitos eléctricos Especificaciones generalesCordones de extensión Herramientas con aislamiento dobleIndice Localización y reparación de averíasGlosario de términos Herramientas necesarias para el ensamblajeThis page intentionally left blank Getting To Know Your Table Saw 12a12bFamiliarisez-vous avec Votre scie de table Familiarización con la sierra De mesa17 c Smart Guard SystemTable Insert Miter GaugeSystème Smart Guard 16. Élément Amovible DE LA Table DE CoupeGuide DE Coupe Angulaire Sistema DE Protector Inteligente Smart GuardUnpacking and Checking Contents Ouverture de l’emballage et Vérification du contenu Desempaquetado yTemps de montage Piezas sueltas en la cartónAdjustments 45 Positive Stops AdjustmentAdjusting the 90 Stop Adjusting the 45 StopRéglage des butées positives 90 et RéglagesAjustesAjuste de los topes positivos De 90 y Plug from power source before mak ngi any Blade Parallel to Miter Gauge Groove AdjustmentProtect your hands Réglages De la lame afin de protéger vos mainsUsing the Correct Blade Removal and Installation BladeTo reduce the risk of injury, do not use Changing the Blade Retrait et installation de la lame Remoción e instalación de la hojaUtiliser la lame correcte Utilización de la hoja correctaUsing Carbide-Tipped Blades Utilisation de lames à pointes Au carbure Utilización de hojas con punta de carburoMiter Gauge Adjustment Manual Pointer AdjustmentAligning Rip Fence Ajustes Attaching the Smart Guard System Positioning the Riving KnifeAssemblageEnsamblaje Montage du système Smart GuardPositionnement DU Couteau Diviseur Posicionamiento DE LA Cuchilla SeparadoraAttaching the Guard Assembly Attaching the ANTI-KICKBACK DeviceInstalación DEL Ensamblaje DEL Protector Montage DE Lensemble DE Barrière DE SécuritéInstalación DEL Dispositivo Antirretroceso Assembly Attaching Rip FenceAssembling the Leg Stand Mounting the Table Saw To the Leg StandAssemblage EnsamblajeMounting Table Saw Mounting to PlywoodInstallation de la scie De table Montaje de la sierra de MesaOn/Off Switch with Safety Key Keeping the Area CleanBasic Table Saw Operation Funcionamiento básico de la Sierra de mesa Maintien de la propreté De la zone de travailMantenga limpia el área Interrupteur marche/arrêt Avec clé de sécuritéComponent Parts figure ❶ Riving Knife❷ Main Barrier Guard ❸ Anti-Kickback DeviceSystème Smart Guard Sistema de protector inteligente Smart GuardComposants Figure Piezas componentes figuraSee page 40 for detailed instructions Attachment/RemovalSystem Storage Montage/démontage Instalación/desinstalaciónRangement du système Almacenamiento del sistemaUsing the Miter Gauge with T Bar Calibre DE Ingletes Avec la barre en « T »Otra Razon Auxiliary Fence Push Stick and Push BlockWorkpiece Guide de coupe auxiliaire Tope-guía auxiliarCrosscutting Coupe transversale Coupe à répétitionCorte transversal Corte repetitivoMiter Cutting Fence / Work SUPPORT, Push Stick or Push BlockCoupe angulaire Coupe transversale biseautéeCoupe angulaire biseautée Utilisation du guide de refenteRipping Bevel RippingCoupe en long Corte al hiloCoupe EN Long Biseautée Corte AL Hilo EN BiselResawing Making a FeatherboardCoupe de dédoublement Fabrication d’une planche à Languettes ReaserradoCómo hacer una tabla con Canto biselado Soires DE Sciage »Install Blade Guard Immediately Upon COM Non Thru-SawingRabbeting Pletion of Rabbeting OperationCoupe partielle Réalisation de feuilluresAserrado no pasante Corte de rebajosInstalling a Dado SET Using Stacked Dado SetsDado and Molding Cutting Is not designed to accept larger sized dadosPage Adjustable or Wobble Dado Sets Returning SAW to Normal THRU-CUTTINGJuegos DE Mortajar Ajustables U Oscilantes Regreso DE LA Sierra a Corte Pasante NormalEnsembles DE Lames a Rainurer Reglables OU Oscillantes Maintaining Your Table Saw MaintenanceSpecial Cutting Techniques Entretien de la Scie de table Mantenimiento de la Sierra de mesaEntretien Técnicas de corte especialesLubrication Blade Elevation and Tilting MechanismCare of Blades Lubrification Entretien des lamesLubricación Cuidado de las hojasTrouble Shooting Guide de diagnosticLocalización y reparación De averías Averia LA Sierra no ArrancaSM 2610008289 02-103310 Table Saw 2/2/10 839 AM SM 2610008289 02-103310 Table Saw 2/2/10 839 AM 2610008289 02/10
Top Page Image Contents