Hitachi Koki USA NV83a2, NV65AC, NV 50A1 manual Loading Nails

Page 13

LOADING NAILS

WARNING

When loading nails into Nailer,

1)do not pull trigger;

2)do not depress push lever; and

3)keep Nailer pointed downward.

<NV83A2>

(1)Grip the nail guide and knob with finger.

Press the knob down and swing the nail guide open. And open the magazine cover.

English

(3)Place the nail coil into the magazine.

Uncoil enough nails to reach the driving hole.

Nail holder

Nails

Magazine

(4)1 Uncoil enough nails to reach the driving hole.

2 Insert the first nail into the driving hole and the second nail between the two pawls of the feeder.

3 Fit the nail heads in the guide slot.

Knob

Nail guide

Magazine cover

Driving hole Guide slot First nail 2 3

Nail Guide

4

1

(2)Adjust the position of the plate according to the nail length.

The nail will not feed smoothly if the plate is not correctly adjusted.

Magazine

Magazine cover

Nail holder

NOTE: Before loading nails in the magazine, adjust the plate. If the magazine cover is forcibly closed without adjusting the plate correctly, the nail holder may be damaged.

1Turn the nail holder about 90 degrees

counterclockwise.

2Slide in vertical direction possible.

Lift or lower the nail holder to accept different length nails.

3Adjust the plate to the nail length reference points on the magazine cover and turn the nail holder 90 degrees clockwise until you hear "click".

2"

 

21/4" 23/8"

2

21/2" 23/4"

 

3" 31/4"

1

 

3

Magazine

Nail holder

Guide surface

2Feeder

4Pulling the nails to the right, swing the nail guide closed.

(5)Close the magazine cover first and swing the nail guide closed.

(6)Lock the knob correctly.

Knob

Magazine cover

Nail guide

NOTE: Be careful not to deform the collated wires and not to disengage the nails with the guide surface. Otherwise, the nail guide will not close correctly.

— 13 —

Image 13
Contents Peligro NV 83A2 NV 65AC NV 50A1 CloueurContents Important Information Definitions of Signal WordsNever Point Tool AT Yourself or Others in Work Area SafetyChoice of Triggering Method is Important Always Wear EAR and Head ProtectionCheck for Live Wires Keep Work Area CleanStore Nailer Properly Never USE in Presence of Flammable Liquids or GasesNever USE Nailer Which is Defective or Operating Abnormally Do not OverreachHandle Nailer Correctly Disconnect AIR Hose from Nailer WhenEMPLOYER’S Responsibilities Name of Parts OperationStandard Accessories AccessoriesNail Selection NV65ACAIR Supply Optional AccessoriesApplications Before OperationLubrication Testing the NailerCold Weather Care Adjusting AIR Pressure Loading Nails Nailer Operation Methods of Operation Disconnect AIR Hose from Nailer Adjusting the Nailing DepthMaintenance and Inspection MaintenanceClearing a jam Inspecting the push leverService parts list Service and RepairsMaintenance chart See Operator troubleshooting See Inspecting the magazineProblem Check Method Correction Action WHY HOWInformation Importante Definition DES Mots DE SignalisationAvertissement SecuriteRanger LE Cloueur Correctement Toujours Porter DES Protections ANTI- Bruit ET UN CasqueMaintenir L’AIRE DE Travail Propre Verifier LE LEVIER-POUSSOIR Avant L’UTILISATIONVerifier S’IL Y a DES Fils Sous Tension Rester SUR SES GardesDebrancher LE Tuyau D’AIR DU Cloueur Quand Manipuler LE Cloueur CorrectementNE PAR Retirer LE Couvercle a Poussiere Responsabilites DE L’EMPLOYEURLunettes DE Protection NOM DES Pieces UtilisationAccessoires Avertissement SpecificationsAccessoires Standard Selection DES ClousAvant L’UTILISATION Accessoires EN OptionEnvironnement DE Travail Avertissement Alimentation D’AIREntretien PAR Temps Froid GraissageEssai DU Cloueur LE Cloueur NE Doit PAS Avoir DE Fuite D’AIR Reglage DE LA Pression D’AIR AvertissementLE Cloueur NE Doit PAS Fonctionner LE Cloueur Doit FonctionnerChargement DES Clous Avertissement Utilisation DU Cloueur Methodes D’UTILISATION Debrancher LE Tuyau D’AIR DU Cloueur Reglage DE LA Profondeur DE ClouageToujours Porter DES Lunettes DE Protection Entretien ET Inspection EntretienElimination d’un blocage Inspection du levier-poussoirInspection du magasin Entretien ET Reparations AvertissementRemisage Liste des pièces de rechangeAction Pourquoi Comment Probleme Verification CorrectionDefinición DE LAS Palabras Clave Información ImportanteLesiones DE Gravedad Advertencia SeguridadES Importante LA Elección DE DE Método DE Activación Guarde Adecuadamente EL Clavador Utilice Siempre Protectores Para LOS Oídos Y LA CabezaMantenga EL Área DE Trabajo Limpia Mantenga a LOS Visitantes AlejadosDesconecte LA Manguera DE Aire DEL Clavador Cuando Compruebe SI HAY Cables ActivosPermanezca Alerta Maneje Correctamente EL ClavadorNo Quite EL Tapón Guardapolvo Responsabilidades DEL EmpresarioGafas Protectoras Para LOS Ojos Nomenclatura OperaciónAccesorios Advertencia Selección DE ClavosAccesorios Estándar Suministro DE Aire Peligro Accesorios OpcionalesAplicaciones Antes DE LA OperaciónCuidados Para Climas Fríos LubricaciónPrecaución Prueba DEL Clavador PeligroEL Clavador no Deberá Tener Fugas DE Aire LA Palanca DE Empuje Deberá Accionarse SIN DificultadEL Clavador no Deberá Funcionar EL Clavador Deberá FuncionarCarga DE Clavos Advertencia Ajuste DE LA Presión DE Aire AdvertenciaEspañol Métodos DE Operación Operación DEL ClavadorDesconecte LA Manguera DE Aire DEL Clavador Ajuste DE LA Profundidad DE ClavadoUtilice Siempre Gafas Protectoras Para LOS Ojos Desatascado MantenimientoInspección de la palanca de empuje Inspección de los alimentadoresInspección del cargador Servicio Y Reparaciones AdvertenciaAlmacenamiento Lista de repuestosAcción Para Cómo Problema Método DE Comprobación Solución501 503 100 5MM 6MM4MM 75A M6⋅20 109 22C 3MM 80AKestrel Road Mississauga on L5T 1Z5 Steve Reynolds Blvd Norcross, GA