DeWalt DWE4517 Mounting and Using Flaring Cup Type 11 Wheel, Mounting Flaring CUP Wheel Guard FIG

Page 17

wheelsprovidedwitha 5/8"-11threadedhubAType27guardis. requiredwhenusingwirebrushesandwheels.

i_WARNING:,Wear work gloves when handling wire brushes or wheels. Wire brushes and wheels can become sharp.

MOUNTING WIRE BRUSHES AND WIRE WHEELS

1.Thread the wheel on the spindle by hand, seating the wheel against the soft mount.

2.Depress the spindle lock button and use a wrench on the hub of the wire brush or wheel to tighten the wheel.

3.To remove the wheel, depress the spindle lock button and use a wrench on the hub of the wire brush or wheel to loosen it.

NOTE" Failure to properly seat the wheel hub against the soft mount before turning the tool on may result in damage to the tool or wheel.

USING WIRE CUP BRUSHES AND WIRE FIG.13

WHEELS (FIG. 13)

Wire wheels and brushes can be used for removing rust, scale and paint, and for smoothing irregular surfaces.

1. Allow tool to reach full speed before0° touching tool to work surface.

2.Apply minimum pressure to work surface, to allow the tool to operate at high speed.

3.Maintain a 5°to 10°angle between the tool and work surface for wire cup brushes.

4.Maintain contact between the edge of the wheel and the work surface with wire wheels.

5.Continuously move the tool in a forward and back motion to avoid creating gouges in the work surface. Allowing the tool to

rest on the work surface without moving, or moving the tool in a

16

circular motion causes burning and swirling marks on the work surface.

6.Remove the tool from the work surface before turning the tool off. Allow the tool to stop rotating before setting it down.

Mounting and Using Flaring Cup (Type 11) Wheel

MOUNTING FLARING CUP WHEEL GUARD (FIG. 14)

it, WARNING: The flaring cup wheel guard is not included with this tool Flaring cup wheels require proper flanges and guards. 4" flaring cup wheel guard D284934 and 6" flaring cup wheel guard D284936 are available as accessories and include proper flange. Failure to use the proper flange and guard can result in injury resulting from wheel

breakage and wheel contact.

FIG. 14

1.Install the guard as shown.

2.Guard body should be positioned between the spindle and the operator to provide maximum operator protection.

3.Securely tighten the two clamping screws (P) supplied with the guard.

MOUNTING FLARING CUP WHEEL (FIG. 15)

1.Remove the soft mount (F).

2.Install the flaring cup wheel backing flange, aligning the flats on spindle (Q)with the flats on backing flange (R).

3.Thread the flaring cup wheel on spindle by hand, seating wheel against backing flange.

4.Depress the spindle lock button and tighten the wheel by hand.

5.To remove the wheel, reverse the above procedure.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Instructivo DE OPERACION, Centros DE SERVlCIO Y Poliza DE General Power Tool Safety Warnings Definitions Safety GuidelinesDo not expose power tools to rain or wet conditions Save ALL Warnings and Instructions For Future ReferencePower Tool USE and Care Personal SafetyAbrasive, Cutting-Off Operations Safety Instructions for ALL OperationsPosition the cord clear of the spinning accessory, if you Safety Warnings Specific for GrindingKickback and Related Warnings Abrasive Cutting-OffOperationsOperations Additional Safety Warnings Specific forSafety Warnings Specific for Polishing Additional Safety Rules for Grinders Safety Warnings Specific for Wire Brushing OperationsMinimum Gauge for Cord Sets Volts Ampere RatingMotor Save These Instructions for Future USEFamiliarization Accessories and Attachments FeaturesAttaching the Side Handle Fig Assembly and AdjustmentsRotating the Gear Case Fig OperationSwitch Fig Power SourceBe unableto rotatetheguardby Guardinto the desiredworking Positionthat providesmaximumClosedposition Mounting and Removing Hubbed WheelsGrinding Wheels Sanding Discs Softmount Type27guard D2849377 D2849399Wheels Wire WheelsFlaring Cup Stones Surface Grinding with Grinding Wheels FIG Mounting NON-HUBBED Wheels FIGEdge Grinding with Grinding Wheels Surface Finishing with Sanding Flap Discs FIGMounting and Using Sanding Backing Pads ThetooltostoprotatingbeforesettingitdownMounting and Using Wire Brushes Wire WheelsMounting Wire Brushes and Wire Wheels Mounting and Using Flaring Cup Type 11 WheelUsing Wire CUP Brushes and Wire Wheels FIG Mounting Flaring CUP Wheel Guard FIGUsing a Flaring CUP Wheel FIG Mounting Using CuttingType Wheels Mounting Closed Type 1 GuardAccessories MaintenanceUsing Cutting Wheels FIG Mounting curIING Wheels FIGRepairs Three Year Limited WarrantyDewalt.com Sicuriti EN MATI#RE Dilectriciti Dfinitions lignes directrices en matire de scuritAvertissements de scurit gnraux pour les outils lectriques Empcher les dmarrages intempestifs. Sassurer que Sicuriti PersonnelleNe pas utiliser un outil electrique dont Iinterrupteur Consignes DE Securite Pour Toutes LES OperationsAvertissements de scurit communs Ne jamais utiliser un accessoire endommag. Avant Rebonds et avertissements affrents Par abrasion Supplmentaires spcifiques auxAvertissements de scurit Operations de coupe par abrasion=tre attentif, car la brosse peut projeter des soies Rgles additionnelles de scurit propresAux meuleuses Avertissement porter Systematiquement des lunettes Moteur Conserver CES Consignes Pour Utilisation UlterieureFamiliarisa Tion Caractristiques Description FigInstallation De la poigne Accessoires et raccordsAssemblage ET Reglage Positionnement du carterSource dalimentation FonctionnementInterrupteur gchette Fig Disques de pon age feuilletsD284938po D284937po D284939po Type27hubbedwheelMeules Disques de poneageMeules abrasives Brosses mdtalliques circulairesMeules boisseaux Coniques Retrait DU Bouton DE VERROUlLLAGE EN Position DE Marche FIG Installation ET Retrait DU Dispositif DE Protection FIGPonage feuillets Installation DES Meules Sans Moyeu FIG Installation et reftrait des meules avecMoyeu Meulage DE Finition FIGMeulage DE Bordure Installation et utilisation des tampons deSupport Installation DES Tampons DE Support FIG Installation et utilisation des brosses etInstallation DES Brosses ET DES Meules #TALLIOUES Des meules mtalliquesDelabrossea,Iaidedunecle Installation et utilisation des meules Boisseaux coniques nInstallation DES Meules Boisseaux Coniques FIG Installation DU Dispositif DE Protection Installation et utilisation des meules abrasives nOrdreinverse FIG15 Utilisation DES Meules Boisseaux Coniques FIGUtilisation DES Meules Abrasives FIG Installation DES Meules Abrasives FIGNettoyage AccessoiresRdparations Garantie limite de trois ansNotre Remplacement Gratuit DES eTIQUETTESContrat Dentretien Gratuit Dunan Garantie DE Remboursement DE 90 JoursAdvertencias generales de seguridad Definiciones Normas de seguridadPara herramientas elctricas Seguridad EN EL Area DE TrabajoEvite el encendido per accidente. Aseg/rese de que AI operar una herramienta elctrica en el exterior, utiliceConectarlo a la fuente de energia o paquete de baterias USO Y Mantenimiento DE LA HerramientaPulido Para Operaciones Corte Desbaste Abrasivo Instrucciones DE Seguridad Para Todas LAS OperacionesNunca apoye la herramienta hasta que el accesorio se Utilice solo los tipos de disco recomendados para Rebote y advertencias relacionadasAbrasivos Abrasivo Advertencias de seguridad adicionalesAdvertencias de seguridad especificas Especificas para operaciones de cortePara operaciones de cepillado con cepillo de alambre Normas de seguridad adicionales para esmeriladorasPara operaciones de pulido Loshilosdecadaalargadortenganel calibre mfnimo. La tabla Componentes Fig Conocimiento DEL ProductoGuarde Estas Instrucciones Para Futuras Consultas Accesorios y dispositivos CaracteristicasEngranajes Ensamblaje Y AjustesInstalaci6n Del Mango Lateral Como girar Caja deGuardatipo28 D2849389 Guardatipo27 D2849377 D2849399 Discodetipo27Discotipo28 Discos para esmerilar Discos de lijarDiscos de corte Cepillos de alambreCopa de Piedra Alimentaci6n de corriente OperacionInterruptor Fig Instalaci6n y utilizaci6n de los discos deInstalacion DE Discos CON Centrodeprimido FIG Instalaci6n y remoci6n de los discos de cuboInstalacion Y Remocion DE LA Guarda FIG Esmerilado DE CON Discos DE Esmerilar FIG Coloqueeldiscocontralacentr6,ndolaelflanjeEsmerilado DE Bordes CON Discos DE Esmerilar Acabado DE Superficies CON Discos DE Aleta Para Lijar FIGRuedas de alambre Instalacibn y utilizacibn de las para lijarInstalacibn y utilizacibn de copas y Instalacion DE Respaldo DE Goma Para Lijar FIGDe copa Instalaci6n y utilizaci6n de piedrasInstalacion DE Copas Y Discos DE Alambre Instalacion DE LA Guarda DE LAS Piedras DE Copa FIGInstalacidn y utilizacidn de discos de corte tipo Respaldo Oprimaelbot0ndelsegurodelejeyaprieteeldiscoUtilizacion DE UNA Piedra DE Copa FIG Instalacion DE Guarda Cerrada Tipo 1Limpieza MantenimientoInstalacion DE Discos DE Corte FIG Utilizacion DE Discos DE Corte FIGReparaciones AccesoriosP61iza De Garantia Garantia limitada por tres aosExoepoion ES Aiio DE Servicio GratuitoEspecificaciones Reemplazo Gratuito DE LAS Etiquetas DEDWE4517 DWE4519Required Guard

DWE4519, DWE4517 specifications

DeWalt, a renowned name in the power tool industry, continues to deliver exceptional equipment for professionals in various trades. Among its impressive lineup are the DWE4519 and DWE4517 angle grinders. These tools embody innovation, durability, and performance, tailored to handle rigorous tasks with ease.

The DeWalt DWE4519 is a robust 9-inch angle grinder designed for the heaviest grinding, cutting, and polishing applications. This tool stands out with its powerful 4.0 HP motor, delivering an impressive no-load speed of 6,000 RPM, ensuring maximum productivity. One significant feature of the DWE4519 is its exclusive dust ejection system, which helps to protect the tool from damaging dust and debris, enhancing its longevity. Additionally, the electronic clutch prevents kickback in case of a wheel bind-up, enhancing operator safety.

On the other hand, the DeWalt DWE4517 is a slightly smaller model, featuring an 7-inch wheel design. It is equipped with a powerful 4.0 HP motor, allowing for a no-load speed of 6,500 RPM, making it ideal for a wide range of applications, from metalworking to masonry projects. A key feature of the DWE4517 is its adjustable guard, which provides added versatility when cutting or grinding different materials. The magnesium housing makes this grinder lighter without compromising structural integrity, ensuring it can withstand tough job site conditions.

Both models feature a side handle that can be positioned in multiple ways, providing optimal control and user comfort. The DWE4519 and DWE4517 also include a two-position removable handle, allowing users to customize the grip to suit their working style, which is essential for maintaining precision during labor-intensive tasks.

Safety is a priority in the design of both grinders, demonstrated through their protective features like the electronic braking system, which helps stop the wheel quickly once the trigger is released. Furthermore, the anti-vibration technology integrated into both models minimizes fatigue, making them suitable for prolonged use.

In summary, DeWalt’s DWE4519 and DWE4517 angle grinders are powerhouses that combine advanced technologies and user-centric designs. With their high-performance motors, durability, safety features, and ergonomic designs, these tools are perfect for professionals who demand excellence in their grinding tasks. Whether on the construction site or in a metalworking shop, these grinders are reliable companions for every job.
Top Page Image Contents