DeWalt DWE4519, DWE4517 Type Wheels, Mounting Using Cutting, Using a Flaring CUP Wheel FIG

Page 18

FIG. 15

Mounting

and Using Cutting

FIG. 17

 

(Type 1)

Wheels

I

NOTICE: Failure to properly seat the wheel against backing flange before turning the tool on may result in damage to the tool or the wheel

NOTE: Adjust the guard skirt so that only 1/8" (3.17 mm) of the wheel is exposed by loosening the bolts, allowing the guard to lengthen. Tighten the guard skirt bolts securely before using the grinder.

USING A FLARING CUP WHEEL (FIG. 16}

Flaring cup wheels are designed for heavy material removal.

1. Allow the tool to reach full speed before touching tool to work

surface.FIG.16

2.Apply minimum pressure to work surface, allowing the tool to operate at high speed.

3.Maintain a 5°to 10°angle between the tool and the work surface.

4.Continuously move the tool in a forward and back motion to avoid creating gouges in the work surface.

5.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before setting it down.

Cutting wheels include diamond wheels and abrasive discs. Abrasive cutting wheels for metal and concrete use are available. Diamond blades for concrete cutting can also be used. i_ WARNING: A closed, cutting wheel guard is not included with this tool. Cutting wheels require proper flanges and guards. A 7" cutting guard, D284931, is available as an accessory and includes proper, matching flanges. Failure to use proper flange and guard can result in injury resulting from wheel breakage and wheel contacL

MOUNTING CLOSED (TYPE 1) GUARD (FIG. 17, 18)

1.Open the guard latch (I), and align the lugs with slots on the gear case cover. Position the guard facing backward, as shown.

2.Push the guard down until the guard lug engages and rotates freely in the groove on the gear case hub.

3.Rotate guard (G)into desired working position. The guard body should be positioned between the spindle and the operator to provide maximum operator protection.

4.Close the guard latch to secure the guard on the gear case cover. You should be unable to rotate the guard by hand when the latch is in closed position. Do not operate grinder with a loose guard or

guard latch in open position.

FIG.18

NOTE: The guard is pre-adjusted to the

 

diameter of the gear case hub at the factory. If,

 

after a period of time, the guard becomes

 

loose, tighten the adjusting screw (J) with the

 

guard latch in the closed position.

 

17

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Instructivo DE OPERACION, Centros DE SERVlCIO Y Poliza DE Do not expose power tools to rain or wet conditions Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Save ALL Warnings and Instructions For Future ReferencePersonal Safety Power Tool USE and CareSafety Instructions for ALL Operations Abrasive, Cutting-Off OperationsKickback and Related Warnings Safety Warnings Specific for GrindingPosition the cord clear of the spinning accessory, if you Abrasive Cutting-OffOperationsAdditional Safety Warnings Specific for Safety Warnings Specific for PolishingOperations Minimum Gauge for Cord Sets Volts Safety Warnings Specific for Wire Brushing OperationsAdditional Safety Rules for Grinders Ampere RatingSave These Instructions for Future USE FamiliarizationMotor Features Accessories and AttachmentsRotating the Gear Case Fig Assembly and AdjustmentsAttaching the Side Handle Fig OperationPower Source Switch FigClosedposition Guardinto the desiredworking Positionthat providesmaximumBe unableto rotatetheguardby Mounting and Removing Hubbed WheelsSoftmount Type27guard D2849377 D2849399 Grinding Wheels Sanding DiscsWire Wheels Flaring Cup StonesWheels Edge Grinding with Grinding Wheels Mounting NON-HUBBED Wheels FIGSurface Grinding with Grinding Wheels FIG Surface Finishing with Sanding Flap Discs FIGMounting and Using Wire Brushes ThetooltostoprotatingbeforesettingitdownMounting and Using Sanding Backing Pads Wire WheelsUsing Wire CUP Brushes and Wire Wheels FIG Mounting and Using Flaring Cup Type 11 WheelMounting Wire Brushes and Wire Wheels Mounting Flaring CUP Wheel Guard FIGType Wheels Mounting Using CuttingUsing a Flaring CUP Wheel FIG Mounting Closed Type 1 GuardUsing Cutting Wheels FIG MaintenanceAccessories Mounting curIING Wheels FIGThree Year Limited Warranty Dewalt.comRepairs Dfinitions lignes directrices en matire de scurit Avertissements de scurit gnraux pour les outils lectriquesSicuriti EN MATI#RE Dilectriciti Sicuriti Personnelle Empcher les dmarrages intempestifs. Sassurer queConsignes DE Securite Pour Toutes LES Operations Avertissements de scurit communsNe pas utiliser un outil electrique dont Iinterrupteur Ne jamais utiliser un accessoire endommag. Avant Rebonds et avertissements affrents Avertissements de scurit Supplmentaires spcifiques auxPar abrasion Operations de coupe par abrasionRgles additionnelles de scurit propres Aux meuleuses=tre attentif, car la brosse peut projeter des soies Avertissement porter Systematiquement des lunettes Conserver CES Consignes Pour Utilisation Ulterieure Familiarisa TionMoteur Description Fig CaractristiquesAssemblage ET Reglage Accessoires et raccordsInstallation De la poigne Positionnement du carterInterrupteur gchette Fig FonctionnementSource dalimentation Disques de pon age feuilletsMeules D284937po D284939po Type27hubbedwheelD284938po Disques de poneageBrosses mdtalliques circulaires Meules boisseaux ConiquesMeules abrasives Installation ET Retrait DU Dispositif DE Protection FIG Ponage feuilletsRetrait DU Bouton DE VERROUlLLAGE EN Position DE Marche FIG Moyeu Installation et reftrait des meules avecInstallation DES Meules Sans Moyeu FIG Meulage DE Finition FIGInstallation et utilisation des tampons de SupportMeulage DE Bordure Installation DES Brosses ET DES Meules #TALLIOUES Installation et utilisation des brosses etInstallation DES Tampons DE Support FIG Des meules mtalliquesInstallation et utilisation des meules Boisseaux coniques n Installation DES Meules Boisseaux Coniques FIGDelabrossea,Iaidedunecle Ordreinverse FIG15 Installation et utilisation des meules abrasives nInstallation DU Dispositif DE Protection Utilisation DES Meules Boisseaux Coniques FIGInstallation DES Meules Abrasives FIG Utilisation DES Meules Abrasives FIGRdparations AccessoiresNettoyage Garantie limite de trois ansContrat Dentretien Gratuit Dunan Remplacement Gratuit DES eTIQUETTESNotre Garantie DE Remboursement DE 90 JoursPara herramientas elctricas Definiciones Normas de seguridadAdvertencias generales de seguridad Seguridad EN EL Area DE TrabajoConectarlo a la fuente de energia o paquete de baterias AI operar una herramienta elctrica en el exterior, utiliceEvite el encendido per accidente. Aseg/rese de que USO Y Mantenimiento DE LA HerramientaInstrucciones DE Seguridad Para Todas LAS Operaciones Pulido Para Operaciones Corte Desbaste AbrasivoNunca apoye la herramienta hasta que el accesorio se Rebote y advertencias relacionadas AbrasivosUtilice solo los tipos de disco recomendados para Advertencias de seguridad especificas Advertencias de seguridad adicionalesAbrasivo Especificas para operaciones de corteNormas de seguridad adicionales para esmeriladoras Para operaciones de pulidoPara operaciones de cepillado con cepillo de alambre Loshilosdecadaalargadortenganel calibre mfnimo. La tabla Conocimiento DEL Producto Guarde Estas Instrucciones Para Futuras ConsultasComponentes Fig Caracteristicas Accesorios y dispositivosInstalaci6n Del Mango Lateral Ensamblaje Y AjustesEngranajes Como girar Caja deDiscotipo28 Guardatipo27 D2849377 D2849399 Discodetipo27Guardatipo28 D2849389 Discos para esmerilar Discos de lijarCepillos de alambre Copa de PiedraDiscos de corte Interruptor Fig OperacionAlimentaci6n de corriente Instalaci6n y utilizaci6n de los discos deInstalaci6n y remoci6n de los discos de cubo Instalacion Y Remocion DE LA Guarda FIGInstalacion DE Discos CON Centrodeprimido FIG Esmerilado DE Bordes CON Discos DE Esmerilar Coloqueeldiscocontralacentr6,ndolaelflanjeEsmerilado DE CON Discos DE Esmerilar FIG Acabado DE Superficies CON Discos DE Aleta Para Lijar FIGInstalacibn y utilizacibn de copas y Instalacibn y utilizacibn de las para lijarRuedas de alambre Instalacion DE Respaldo DE Goma Para Lijar FIGInstalacion DE Copas Y Discos DE Alambre Instalaci6n y utilizaci6n de piedrasDe copa Instalacion DE LA Guarda DE LAS Piedras DE Copa FIGUtilizacion DE UNA Piedra DE Copa FIG Respaldo Oprimaelbot0ndelsegurodelejeyaprieteeldiscoInstalacidn y utilizacidn de discos de corte tipo Instalacion DE Guarda Cerrada Tipo 1Instalacion DE Discos DE Corte FIG MantenimientoLimpieza Utilizacion DE Discos DE Corte FIGAccesorios ReparacionesExoepoion ES Garantia limitada por tres aosP61iza De Garantia Aiio DE Servicio GratuitoDWE4517 Reemplazo Gratuito DE LAS Etiquetas DEEspecificaciones DWE4519Required Guard

DWE4519, DWE4517 specifications

DeWalt, a renowned name in the power tool industry, continues to deliver exceptional equipment for professionals in various trades. Among its impressive lineup are the DWE4519 and DWE4517 angle grinders. These tools embody innovation, durability, and performance, tailored to handle rigorous tasks with ease.

The DeWalt DWE4519 is a robust 9-inch angle grinder designed for the heaviest grinding, cutting, and polishing applications. This tool stands out with its powerful 4.0 HP motor, delivering an impressive no-load speed of 6,000 RPM, ensuring maximum productivity. One significant feature of the DWE4519 is its exclusive dust ejection system, which helps to protect the tool from damaging dust and debris, enhancing its longevity. Additionally, the electronic clutch prevents kickback in case of a wheel bind-up, enhancing operator safety.

On the other hand, the DeWalt DWE4517 is a slightly smaller model, featuring an 7-inch wheel design. It is equipped with a powerful 4.0 HP motor, allowing for a no-load speed of 6,500 RPM, making it ideal for a wide range of applications, from metalworking to masonry projects. A key feature of the DWE4517 is its adjustable guard, which provides added versatility when cutting or grinding different materials. The magnesium housing makes this grinder lighter without compromising structural integrity, ensuring it can withstand tough job site conditions.

Both models feature a side handle that can be positioned in multiple ways, providing optimal control and user comfort. The DWE4519 and DWE4517 also include a two-position removable handle, allowing users to customize the grip to suit their working style, which is essential for maintaining precision during labor-intensive tasks.

Safety is a priority in the design of both grinders, demonstrated through their protective features like the electronic braking system, which helps stop the wheel quickly once the trigger is released. Furthermore, the anti-vibration technology integrated into both models minimizes fatigue, making them suitable for prolonged use.

In summary, DeWalt’s DWE4519 and DWE4517 angle grinders are powerhouses that combine advanced technologies and user-centric designs. With their high-performance motors, durability, safety features, and ergonomic designs, these tools are perfect for professionals who demand excellence in their grinding tasks. Whether on the construction site or in a metalworking shop, these grinders are reliable companions for every job.
Top Page Image Contents