DeWalt DWE4517 Maintenance, Accessories, Mounting curIING Wheels FIG, Using Cutting Wheels FIG

Page 19

NOTICE: Do not tighten adjusting screw with guard latch in open position. Undetectable damage to guard or mounting hub may result.

MOUNTING cu'rI'ING WHEELS (FIG. 19)

1.Remove soft mount (E).

2.Install wheel backing flange, aligning flats on spindle (R)with flats on backing flange (S).

3.Place the wheel on the backing flange, centering the wheel on the backing flange pilot.

4.Install the clamp nut, ensuring that the wheel remains centered on the backing flange.

5.Depress the spindle lock button and tighten clamp nut with wrench.

6.Reverse the above procedure to remove the wheel.

FIG. 19

2.Apply minimum pressure to work surface, FIG.20 allowing tool to operate at high speed.

3.Once you begin a cut, maintain the angle of the cutting wheel to the work surface. This will keep you from bending the wheel which could result in wheel breakage and injury.

4.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before setting it down.

MAINTENANCE

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

USING CUTTING WHEELS (FIG. 20)

,_,WARNING: Do not use edge grinding/cutting wheels for surface

grinding applications because these wheels are not designed for side pressures encountered with surface grinding. Wheel breakage and

injury may result.

1.Allow tool to reach full speed before touching tool to work surface.

Cleaning

A WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing this.

_ WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool," never immerse any part of the tool into a liquid.

Accessories

/_ WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT recommended accessories should be used with this product.

18

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Instructivo DE OPERACION, Centros DE SERVlCIO Y Poliza DE Save ALL Warnings and Instructions For Future Reference Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Do not expose power tools to rain or wet conditionsPower Tool USE and Care Personal SafetyAbrasive, Cutting-Off Operations Safety Instructions for ALL OperationsAbrasive Cutting-OffOperations Safety Warnings Specific for GrindingPosition the cord clear of the spinning accessory, if you Kickback and Related WarningsSafety Warnings Specific for Polishing Additional Safety Warnings Specific forOperations Ampere Rating Safety Warnings Specific for Wire Brushing OperationsAdditional Safety Rules for Grinders Minimum Gauge for Cord Sets VoltsFamiliarization Save These Instructions for Future USEMotor Accessories and Attachments FeaturesOperation Assembly and AdjustmentsAttaching the Side Handle Fig Rotating the Gear Case FigSwitch Fig Power SourceMounting and Removing Hubbed Wheels Guardinto the desiredworking Positionthat providesmaximumBe unableto rotatetheguardby ClosedpositionGrinding Wheels Sanding Discs Softmount Type27guard D2849377 D2849399Flaring Cup Stones Wire WheelsWheels Surface Finishing with Sanding Flap Discs FIG Mounting NON-HUBBED Wheels FIGSurface Grinding with Grinding Wheels FIG Edge Grinding with Grinding WheelsWire Wheels ThetooltostoprotatingbeforesettingitdownMounting and Using Sanding Backing Pads Mounting and Using Wire BrushesMounting Flaring CUP Wheel Guard FIG Mounting and Using Flaring Cup Type 11 WheelMounting Wire Brushes and Wire Wheels Using Wire CUP Brushes and Wire Wheels FIGMounting Closed Type 1 Guard Mounting Using CuttingUsing a Flaring CUP Wheel FIG Type WheelsMounting curIING Wheels FIG MaintenanceAccessories Using Cutting Wheels FIGDewalt.com Three Year Limited WarrantyRepairs Avertissements de scurit gnraux pour les outils lectriques Dfinitions lignes directrices en matire de scuritSicuriti EN MATI#RE Dilectriciti Empcher les dmarrages intempestifs. Sassurer que Sicuriti PersonnelleAvertissements de scurit communs Consignes DE Securite Pour Toutes LES OperationsNe pas utiliser un outil electrique dont Iinterrupteur Ne jamais utiliser un accessoire endommag. Avant Rebonds et avertissements affrents Operations de coupe par abrasion Supplmentaires spcifiques auxPar abrasion Avertissements de scuritAux meuleuses Rgles additionnelles de scurit propres=tre attentif, car la brosse peut projeter des soies Avertissement porter Systematiquement des lunettes Familiarisa Tion Conserver CES Consignes Pour Utilisation UlterieureMoteur Caractristiques Description FigPositionnement du carter Accessoires et raccordsInstallation De la poigne Assemblage ET ReglageDisques de pon age feuillets FonctionnementSource dalimentation Interrupteur gchette FigDisques de poneage D284937po D284939po Type27hubbedwheelD284938po MeulesMeules boisseaux Coniques Brosses mdtalliques circulairesMeules abrasives Ponage feuillets Installation ET Retrait DU Dispositif DE Protection FIGRetrait DU Bouton DE VERROUlLLAGE EN Position DE Marche FIG Meulage DE Finition FIG Installation et reftrait des meules avecInstallation DES Meules Sans Moyeu FIG MoyeuSupport Installation et utilisation des tampons deMeulage DE Bordure Des meules mtalliques Installation et utilisation des brosses etInstallation DES Tampons DE Support FIG Installation DES Brosses ET DES Meules #TALLIOUESInstallation DES Meules Boisseaux Coniques FIG Installation et utilisation des meules Boisseaux coniques nDelabrossea,Iaidedunecle Utilisation DES Meules Boisseaux Coniques FIG Installation et utilisation des meules abrasives nInstallation DU Dispositif DE Protection Ordreinverse FIG15Utilisation DES Meules Abrasives FIG Installation DES Meules Abrasives FIGGarantie limite de trois ans AccessoiresNettoyage RdparationsGarantie DE Remboursement DE 90 Jours Remplacement Gratuit DES eTIQUETTESNotre Contrat Dentretien Gratuit DunanSeguridad EN EL Area DE Trabajo Definiciones Normas de seguridadAdvertencias generales de seguridad Para herramientas elctricasUSO Y Mantenimiento DE LA Herramienta AI operar una herramienta elctrica en el exterior, utiliceEvite el encendido per accidente. Aseg/rese de que Conectarlo a la fuente de energia o paquete de bateriasPulido Para Operaciones Corte Desbaste Abrasivo Instrucciones DE Seguridad Para Todas LAS OperacionesNunca apoye la herramienta hasta que el accesorio se Abrasivos Rebote y advertencias relacionadasUtilice solo los tipos de disco recomendados para Especificas para operaciones de corte Advertencias de seguridad adicionalesAbrasivo Advertencias de seguridad especificasPara operaciones de pulido Normas de seguridad adicionales para esmeriladorasPara operaciones de cepillado con cepillo de alambre Loshilosdecadaalargadortenganel calibre mfnimo. La tabla Guarde Estas Instrucciones Para Futuras Consultas Conocimiento DEL ProductoComponentes Fig Accesorios y dispositivos CaracteristicasComo girar Caja de Ensamblaje Y AjustesEngranajes Instalaci6n Del Mango LateralDiscos para esmerilar Discos de lijar Guardatipo27 D2849377 D2849399 Discodetipo27Guardatipo28 D2849389 Discotipo28Copa de Piedra Cepillos de alambreDiscos de corte Instalaci6n y utilizaci6n de los discos de OperacionAlimentaci6n de corriente Interruptor FigInstalacion Y Remocion DE LA Guarda FIG Instalaci6n y remoci6n de los discos de cuboInstalacion DE Discos CON Centrodeprimido FIG Acabado DE Superficies CON Discos DE Aleta Para Lijar FIG Coloqueeldiscocontralacentr6,ndolaelflanjeEsmerilado DE CON Discos DE Esmerilar FIG Esmerilado DE Bordes CON Discos DE EsmerilarInstalacion DE Respaldo DE Goma Para Lijar FIG Instalacibn y utilizacibn de las para lijarRuedas de alambre Instalacibn y utilizacibn de copas yInstalacion DE LA Guarda DE LAS Piedras DE Copa FIG Instalaci6n y utilizaci6n de piedrasDe copa Instalacion DE Copas Y Discos DE AlambreInstalacion DE Guarda Cerrada Tipo 1 Respaldo Oprimaelbot0ndelsegurodelejeyaprieteeldiscoInstalacidn y utilizacidn de discos de corte tipo Utilizacion DE UNA Piedra DE Copa FIGUtilizacion DE Discos DE Corte FIG MantenimientoLimpieza Instalacion DE Discos DE Corte FIGReparaciones AccesoriosAiio DE Servicio Gratuito Garantia limitada por tres aosP61iza De Garantia Exoepoion ESDWE4519 Reemplazo Gratuito DE LAS Etiquetas DEEspecificaciones DWE4517Required Guard

DWE4519, DWE4517 specifications

DeWalt, a renowned name in the power tool industry, continues to deliver exceptional equipment for professionals in various trades. Among its impressive lineup are the DWE4519 and DWE4517 angle grinders. These tools embody innovation, durability, and performance, tailored to handle rigorous tasks with ease.

The DeWalt DWE4519 is a robust 9-inch angle grinder designed for the heaviest grinding, cutting, and polishing applications. This tool stands out with its powerful 4.0 HP motor, delivering an impressive no-load speed of 6,000 RPM, ensuring maximum productivity. One significant feature of the DWE4519 is its exclusive dust ejection system, which helps to protect the tool from damaging dust and debris, enhancing its longevity. Additionally, the electronic clutch prevents kickback in case of a wheel bind-up, enhancing operator safety.

On the other hand, the DeWalt DWE4517 is a slightly smaller model, featuring an 7-inch wheel design. It is equipped with a powerful 4.0 HP motor, allowing for a no-load speed of 6,500 RPM, making it ideal for a wide range of applications, from metalworking to masonry projects. A key feature of the DWE4517 is its adjustable guard, which provides added versatility when cutting or grinding different materials. The magnesium housing makes this grinder lighter without compromising structural integrity, ensuring it can withstand tough job site conditions.

Both models feature a side handle that can be positioned in multiple ways, providing optimal control and user comfort. The DWE4519 and DWE4517 also include a two-position removable handle, allowing users to customize the grip to suit their working style, which is essential for maintaining precision during labor-intensive tasks.

Safety is a priority in the design of both grinders, demonstrated through their protective features like the electronic braking system, which helps stop the wheel quickly once the trigger is released. Furthermore, the anti-vibration technology integrated into both models minimizes fatigue, making them suitable for prolonged use.

In summary, DeWalt’s DWE4519 and DWE4517 angle grinders are powerhouses that combine advanced technologies and user-centric designs. With their high-performance motors, durability, safety features, and ergonomic designs, these tools are perfect for professionals who demand excellence in their grinding tasks. Whether on the construction site or in a metalworking shop, these grinders are reliable companions for every job.
Top Page Image Contents