DeWalt DWE4517, DWE4519 Safety Warnings Specific for Wire Brushing Operations, Ampere Rating

Page 7

Safety Warnings Specific for Wire Brushing Operations

a)Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/or skin.

b)If the use of a guard is recommended for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work and centrifugal forces.

Additional Safety Rules for Grinders

WARNING: The grinding wheel or accessory may loosen during coast-down of the tool when shut off. If grinding wheel

or accessory loosens, it may dismount from the machine and may cause serious personal injury.

•Use of accessories not specified in this manual is not recommended and may be hazardous. Use of power boosters that would cause the tool to be driven at speeds greater than its rated speed constitutes misuse.

•Use clamps or anotherpractical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control

•Avoid bouncing the wheel or giving it rough treatment. If this occurs, stop the tool and inspect the wheel for cracks or flaws.

•Always handle and store wheels in a careful manner.

•Never cut into area that may contain electrical wiring or piping. Serious injury may result.

•Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use.

Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in moving parts.

When not in use, place grinder on a stable surface where it will not move inadvertantly, roll or cause a tripping or falling hazard. Serious personal injury may result.

An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

 

Minimum Gauge for Cord Sets

 

 

Volts

 

Total Length of Cord

 

 

 

in Feet (meters)

 

Ampere Rating

 

 

25 (7.6)

50 (15.2)

100 (30.5) 150 (45.7)

 

120V

 

240V

50 (15.2)

100 (30.5) 200 (61.0) 300 (91.4)

More

Not More

 

AWG

 

 

Than

Than

 

 

 

 

 

 

 

0

6

18

16

16

14

6

10

18

16

14

12

10

12

16

16

14

12

12

16

14

12

NotRecommended

_ WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOTsafety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT_

• ANSI Z8 7.1 eye protection (CAN/CSA Z94.3),

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Instructivo DE OPERACION, Centros DE SERVlCIO Y Poliza DE Save ALL Warnings and Instructions For Future Reference Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Do not expose power tools to rain or wet conditionsPower Tool USE and Care Personal Safety Abrasive, Cutting-Off Operations Safety Instructions for ALL OperationsAbrasive Cutting-OffOperations Safety Warnings Specific for GrindingPosition the cord clear of the spinning accessory, if you Kickback and Related WarningsSafety Warnings Specific for Polishing Additional Safety Warnings Specific forOperations Ampere Rating Safety Warnings Specific for Wire Brushing OperationsAdditional Safety Rules for Grinders Minimum Gauge for Cord Sets VoltsFamiliarization Save These Instructions for Future USEMotor Accessories and Attachments FeaturesOperation Assembly and AdjustmentsAttaching the Side Handle Fig Rotating the Gear Case FigSwitch Fig Power SourceMounting and Removing Hubbed Wheels Guardinto the desiredworking Positionthat providesmaximumBe unableto rotatetheguardby ClosedpositionGrinding Wheels Sanding Discs Softmount Type27guard D2849377 D2849399Flaring Cup Stones Wire WheelsWheels Surface Finishing with Sanding Flap Discs FIG Mounting NON-HUBBED Wheels FIGSurface Grinding with Grinding Wheels FIG Edge Grinding with Grinding WheelsWire Wheels ThetooltostoprotatingbeforesettingitdownMounting and Using Sanding Backing Pads Mounting and Using Wire BrushesMounting Flaring CUP Wheel Guard FIG Mounting and Using Flaring Cup Type 11 WheelMounting Wire Brushes and Wire Wheels Using Wire CUP Brushes and Wire Wheels FIGMounting Closed Type 1 Guard Mounting Using CuttingUsing a Flaring CUP Wheel FIG Type WheelsMounting curIING Wheels FIG MaintenanceAccessories Using Cutting Wheels FIGDewalt.com Three Year Limited WarrantyRepairs Avertissements de scurit gnraux pour les outils lectriques Dfinitions lignes directrices en matire de scuritSicuriti EN MATI#RE Dilectriciti Empcher les dmarrages intempestifs. Sassurer que Sicuriti PersonnelleAvertissements de scurit communs Consignes DE Securite Pour Toutes LES OperationsNe pas utiliser un outil electrique dont Iinterrupteur Ne jamais utiliser un accessoire endommag. Avant Rebonds et avertissements affrents Operations de coupe par abrasion Supplmentaires spcifiques auxPar abrasion Avertissements de scuritAux meuleuses Rgles additionnelles de scurit propres=tre attentif, car la brosse peut projeter des soies Avertissement porter Systematiquement des lunettes Familiarisa Tion Conserver CES Consignes Pour Utilisation UlterieureMoteur Caractristiques Description FigPositionnement du carter Accessoires et raccordsInstallation De la poigne Assemblage ET ReglageDisques de pon age feuillets FonctionnementSource dalimentation Interrupteur gchette FigDisques de poneage D284937po D284939po Type27hubbedwheelD284938po MeulesMeules boisseaux Coniques Brosses mdtalliques circulairesMeules abrasives Ponage feuillets Installation ET Retrait DU Dispositif DE Protection FIGRetrait DU Bouton DE VERROUlLLAGE EN Position DE Marche FIG Meulage DE Finition FIG Installation et reftrait des meules avecInstallation DES Meules Sans Moyeu FIG MoyeuSupport Installation et utilisation des tampons deMeulage DE Bordure Des meules mtalliques Installation et utilisation des brosses etInstallation DES Tampons DE Support FIG Installation DES Brosses ET DES Meules #TALLIOUESInstallation DES Meules Boisseaux Coniques FIG Installation et utilisation des meules Boisseaux coniques nDelabrossea,Iaidedunecle Utilisation DES Meules Boisseaux Coniques FIG Installation et utilisation des meules abrasives nInstallation DU Dispositif DE Protection Ordreinverse FIG15Utilisation DES Meules Abrasives FIG Installation DES Meules Abrasives FIGGarantie limite de trois ans AccessoiresNettoyage RdparationsGarantie DE Remboursement DE 90 Jours Remplacement Gratuit DES eTIQUETTESNotre Contrat Dentretien Gratuit DunanSeguridad EN EL Area DE Trabajo Definiciones Normas de seguridadAdvertencias generales de seguridad Para herramientas elctricasUSO Y Mantenimiento DE LA Herramienta AI operar una herramienta elctrica en el exterior, utiliceEvite el encendido per accidente. Aseg/rese de que Conectarlo a la fuente de energia o paquete de bateriasPulido Para Operaciones Corte Desbaste Abrasivo Instrucciones DE Seguridad Para Todas LAS OperacionesNunca apoye la herramienta hasta que el accesorio se Abrasivos Rebote y advertencias relacionadasUtilice solo los tipos de disco recomendados para Especificas para operaciones de corte Advertencias de seguridad adicionalesAbrasivo Advertencias de seguridad especificasPara operaciones de pulido Normas de seguridad adicionales para esmeriladorasPara operaciones de cepillado con cepillo de alambre Loshilosdecadaalargadortenganel calibre mfnimo. La tabla Guarde Estas Instrucciones Para Futuras Consultas Conocimiento DEL ProductoComponentes Fig Accesorios y dispositivos CaracteristicasComo girar Caja de Ensamblaje Y AjustesEngranajes Instalaci6n Del Mango LateralDiscos para esmerilar Discos de lijar Guardatipo27 D2849377 D2849399 Discodetipo27Guardatipo28 D2849389 Discotipo28Copa de Piedra Cepillos de alambreDiscos de corte Instalaci6n y utilizaci6n de los discos de OperacionAlimentaci6n de corriente Interruptor FigInstalacion Y Remocion DE LA Guarda FIG Instalaci6n y remoci6n de los discos de cuboInstalacion DE Discos CON Centrodeprimido FIG Acabado DE Superficies CON Discos DE Aleta Para Lijar FIG Coloqueeldiscocontralacentr6,ndolaelflanjeEsmerilado DE CON Discos DE Esmerilar FIG Esmerilado DE Bordes CON Discos DE EsmerilarInstalacion DE Respaldo DE Goma Para Lijar FIG Instalacibn y utilizacibn de las para lijarRuedas de alambre Instalacibn y utilizacibn de copas yInstalacion DE LA Guarda DE LAS Piedras DE Copa FIG Instalaci6n y utilizaci6n de piedrasDe copa Instalacion DE Copas Y Discos DE AlambreInstalacion DE Guarda Cerrada Tipo 1 Respaldo Oprimaelbot0ndelsegurodelejeyaprieteeldiscoInstalacidn y utilizacidn de discos de corte tipo Utilizacion DE UNA Piedra DE Copa FIGUtilizacion DE Discos DE Corte FIG MantenimientoLimpieza Instalacion DE Discos DE Corte FIGReparaciones AccesoriosAiio DE Servicio Gratuito Garantia limitada por tres aosP61iza De Garantia Exoepoion ESDWE4519 Reemplazo Gratuito DE LAS Etiquetas DEEspecificaciones DWE4517Required Guard
Top Page Image Contents