Brother XL5300, XL5200, XL5100 Inserting the Needle, Inserción de la aguja, Checking the Needle

Page 16

CONNAÎTRE SA MACHINE À COUDRE

CONOZCA SU MÁQUINA DE COSER

KNOWING YOUR SEWING MACHINE

A

1

 

 

 

Inserting the Needle

1

Turn power switch to “O”.

1.

Remove the power supply plug from the electrical outlet.

 

 

 

 

2.

Raise the needle bar to its highest position.

 

 

3.

Lower the presser foot.

 

 

 

 

4.

If a needle is already installed, remove it by loosening the needle

 

 

 

clamp with a coin and pulling the needle down. (See fig. A.)

 

 

5.

With the flat side toward the back, insert the new needle as far as

 

 

 

possible up against the needle stopper.

 

 

6.

Tighten the needle clamp.

1 Coin

B

Inserción de la aguja

Desenchufar la máquina, interruptor principale a “O”.

1.Retire el enchufe de alimentación de la toma de corriente.

2.Levante la barra de la aguja a su posición más alta.

3.Baje el prensatelas.

4.En caso de que ya esté una aguja instalada, retírela aflojando el tornillo con una moneda y tirando hacia abajo. (Ver fig. A.)

5.Introduzca una nueva aguja con la parte plana hacia atrás, lo más adentro posible hasta que llegue a su tope.

6.Vuelva a apretar el tornillo de la aguja.

1Moneda

Checking the Needle

1.The sewing needle must always be straight and sharp for smooth sewing.

2.To check if the needle is bent, place the flat side of the needle down as shown in the illustration. (See fig. B.)

3.Replace the needle if it is bent or dull.

Pour mettre l’aiguille en place

Mettre l’interrupteur principal sur “O”.

1.Retirer la fiche de la prise de courant.

2.Remonter complètement l’aiguille.

3.Abaisser le pied-de-biche.

4.Retirer l’aiguille éventuellement présente en dévissant la fixation avec une pièce de monnaie et en tirant l’aiguille vers le bas. (Voir fig. A.)

5.Introduire une autre aiguille côté plat vers l’arrière, en l’enfonçant au maximum jusqu’à ce qu’elle vienne heurter le butoir.

6.Resserrer la fixation.

1Pièce de monnaie

Comprobación de la aguja

1.La aguja siempre ha de estar bien recta y afilada para un perfec- to cosido.

2.Para comprobar que la aguja no está doblada, coloque la parte plana de la aguja hacia abajo como se muestra en el dibujo. (Ver fig. B.)

3.Cambie la aguja si está doblada o gastada.

Vérification de l’aiguille

1.L’aiguille doit toujours être droite et pointue pour piquer correctement.

2.Pour vérifier si l’aiguille n’est pas tordue, placer le côté plat de l’aiguille vers le bas, comme le montre l’illustration. (Voir fig. B.)

3.Remplacer l’aiguille si elle est tordue ou usée.

7

Image 16
Contents Page Page Important Safety Instructions Conserve Este Manual DE Instrucciones Importantes Consignes DE Securite Connecting Plugs and Main Power / Sewing Light Switch Contents Índice DEL Contenido Conozca SU Máquina DE CoserTable DES Matières Bobbin winding assembly Main power/sewing light switchSpool pin Stitch length dialElementos Principales Accessories AccesoriosXL5100/PX100 Connecting Plugs Funcionamiento DE LA Máquina DE CoserConexión de los enchufes RaccordementMain Power and Sewing Light Switches Interruptor principal y de luzFoot Controller PedalInserting the Needle Inserción de la agujaChecking the Needle Comprobación de la agujaCambio del prensatelas Changing the Presser FootChangement de pied-de-biche Modelo a presiónConverting to Free-Arm Style Conversión en modalidad de brazo LibrePara estabilizar la máquina Steadying the MachineDistintos Mandos Selector de puntadasPattern Selection Dial Sélecteur de modèle de pointRecommended Widths and Lengths for Stitches XL5200/PX200 B-C-D Anchos Y Largos DE Puntadas Recomendados XL5300/PX300XL5200/PX200 1A-B-C-D Longueurs ET Largeurs DE Point Recommandées XL5200/PX200 Point Universel Ourlet Invisible DE Lingerie Selector de largo de puntada Stitch Length DialSélecteur de longueur de point Stretch Stitching Puntada elásticaCouture en points élastiques Selección de la puntada elásticaSelector del ancho de puntada Stitch Width DialSélecteur de largeur de point Palanca de retroceso Levier de couture en marche arrièreEnhebrado DE LA Máquina Winding the BobbinBobinado de la canilla Remplissage de la canetteEnhebrado inferior Lower ThreadingMise en place du fil inférieur Upper Needle Threading Enhebrado superior de la aguja Mise en place du fil supérieur Fil de l’aiguilleWhen the machine is equipped with a Using the Needle ThreaderNeedle threader Enhebrador Palanca del enhebrador Système Rapide Para sacar el hilo de la canilla Drawing Up Lower ThreadRemontée du fil inférieur Costura con aguja doble Twin-Needle SewingCouture avvec l’aiguille jumelée Thread Tension Upper tension is too looseLower tension is too loose BobbinTensión de los hilos Tension des filsChart of Sewing FABRICS, Needles and Thread Combinations Tabla DE Combinaciones Entre TEJIDOS, Agujas Y HilosTableau DES Combinaisons TISSU/AIGUILLE/FIL Straight Stitching Puntadas rectasPoint droit Para empezar a coserCambio de sentido de costura fig. a Para terminar las costuras fig. BChanging Sewing Directions fig. a Finishing Sewing fig. BRemoving the Material From the Machine Topstitching and Stretch MaterialsPara retirar el tejido de la máquina Puntadas en derecho y tejidos elásticosPuntadas zigzag Zigzag StitchingPoint zigzag Blindhem Stitching Puntadas invisiblesOurlet invisible de lingerie Shell Tuck Stitching Puntada alforza derefuerzoPoint à coquilles Point élastique RemiendosInserción de gomas elásticas Puntada de uniónScallop Stitching Puntada festónPuntada universal Universal StitchingOveredge Stitching Puntada por encima de la orillaPoints sur le bord Feather Stitching Puntada plumaPoint plume Triple Zigzag Stretch Stitching Puntada triple zigzag elásticaDecorative Stitching Puntada decorativaMaking a Buttonhole Making a ButtonholeMaking a Buttonhole on Stretch Fabrics fig. E Pour coudre une boutonnière Para coser ojales Solo XL5300, XL5200, PX300 y PX200Cosido de ojales en tejidos elásticos fig. E Making a Buttonhole XL5100 and PX100 only Para coser ojales Solo XL5100 y PX100Pasos Parte Cosida Step Sewn Portion Pattern How to SewComo Coser Phase Partie cousue Modèle Comment coudre Securing the Stitching and Cutting the ButtonholePara Completar las Puntadas y Cortar el Ojal Comment arrêter la couture et ouvrir la boutonnièreButtonhole Fine Adjustment Ajuste fino de los ojales Equilibrage des boutonnièresButton Sewing Costura de botones Pour coudre un boutonZipper Inserting GatheringInserción de cremalleras FruncidoInsertion de fermeture à glissière Pour froncer un tissuDarning ZurcidoReprisage Appliques AplicacionesAppliques Monogramming and Embroidering Monogramas y bordadosMonogrammes et broderies Preparación para monogramas y bordadosMonogramas BordadoEmbroidering MonogrammesChanging the Bulb Remplacement de l’ampouleCambio de la bombilla Oiling EngrasadoGraissage Limpieza CleaningNettoyage Performance Checklist Upper Thread Lower Thread Skipped Loop in Seam FabricFabric does Listado de posibles incidencias Póngase EN Contacto CON EL Servicio Técnico LocalEL Tejido no Arrastra Bien Liste de vérification en cas de défaillances Contacter LE Centre Technique LE Plus ProcheContacter LE Service Technique LE Plus Proche Importante Repacking the MachineEmbalaje de la máquina Emballage de la machineBobbin Threading Winding Bridging Stitch Buttonhole Sewing Aguja Aiguille Page Page Potencia Consumida 90W English Español

XL5100, XL5300, XL5200 specifications

The Brother XL series sewing machines, including the XL5200, XL5300, and XL5100, are versatile and user-friendly models designed for both beginners and experienced sewers. These machines combine functionality with advanced features to cater to a wide range of sewing projects.

The Brother XL5200 is designed to simplify the sewing experience while offering versatility. It features 35 built-in stitches, including decorative, utility, and stretch stitches, providing plenty of options for various projects. The easy-to-read LCD screen allows users to select stitches effortlessly. One of its standout features is the automatic needle threader, eliminating the frustration of threading the needle manually. The machine also comes equipped with a drop-in top bobbin system that ensures smooth and consistent sewing.

The XL5300 builds upon the capabilities of the XL5200, providing additional features that enhance creativity. With 60 built-in stitches, including an impressive selection of decorative stitches and seven one-step auto-size buttonhole options, this model encourages experimentation. The XL5300 also includes a hard case for protection and portability, making it an excellent choice for sewers who attend classes or workshops. Its adjustable stitch width and length allow for customization of stitches, ensuring the outcome perfectly aligns with the user’s vision.

The Brother XL5100 is a great entry-level machine known for its ease of use. This model contains 50 built-in stitches, including essential utility stitches that are perfect for garment construction, quilting, and crafting. Like its counterparts, it features an automatic needle threader and a jam-resistant drop-in bobbin. The XL5100 also offers a convenient free arm that is ideal for sewing sleeves and cuffs. This model is particularly user-friendly, making it an excellent option for beginners looking to develop their sewing skills.

All three models come with various presser feet and accessories that expand their functionality, such as a zipper foot, buttonhole foot, and walking foot for quilting. They are designed with sturdy construction, ensuring durability and longevity for all sewing enthusiasts.

In summary, the Brother XL5200, XL5300, and XL5100 are excellent choices for those looking for reliable sewing machines that offer a blend of user-friendly features, versatility, and performance. Whether for simple alterations or complex projects, these models provide the tools necessary to help bring user creativity to life.