Brother XL5300, XL5200, XL5100 Lower Threading, Enhebrado inferior, Mise en place du fil inférieur

Page 34

CONNAÎTRE SA MACHINE À COUDRE

CONOZCA SU MÁQUINA DE COSER

KNOWING YOUR SEWING MACHINE

A

1

2

B-2

B-1

B-3

3

Lower Threading

Turn power switch to “O”.

1.Raise the needle to its highest position by turning the balance wheel toward you (counterclockwise) and raise the presser foot lever.

2.Open the shuttle cover behind the extension table on the front of the machine and remove the bobbin case by pulling its latch to- ward you and pulling it out from the shuttle race (fig. A).

3.Unwind about 10 cm (4") of thread from a full bobbin and insert the bobbin into the bobbin case. (See fig. B-1.) Pull the trailing thread into the slot, then down and to the left, as shown in fig. B-2, until it enters the delivery eye under the tension spring (fig. B-3).

4.Holding the bobbin case by the latch, fully insert the bobbin case into the shuttle race and release the latch. Make sure the bobbin case finger fits into the notch at the top of the race as shown in fig. C.

NOTE:

If the bobbin case is not properly placed back into the machine, it will fall out from the shuttle immediately after starting to sew.

1Bobbin case latch

2 Bobbin case finger

3 Tension spring

4 Notch

C

2 4

“CAUTION” - “MOVING PARTS-TO REDUCE THE RISK OF INJURY, DISCONNECT FROM SUPPLY CIRCUIT BEFORE SERVICING. RE- PLACE COVER.”

Enhebrado inferior

 

Mise en place du fil inférieur

Desenchufar la máquina, interruptor principale a “O”.

1.Levante la aguja a su posición más alta, girando la ruedecilla hacia usted (en sentido contrario al de las manecillas de un reloj) y levante la palanca del prensatelas.

2.Abra la tapa del soporte para accesorios, en la parte delantera de la máquina, y retire el portacanillas de la máquina, tirando de la uñeta metálica (pestillo) hacia usted y sacándola de la lanza- dera (Ver fig. A.)

3.Tire unos 10 cm (4") de hilo de una canilla llena e inserte la cani- lla en el portacanillas. (Ver fig. B-1.) Tire del hilo suelto y páselo por la hendidura, abajo y hacia la izquierda, tal como se indica en la fig. B-2, hasta que el hilo pase por la abertura de salida debajo del resorte de tensión. (fig. B-3)

4.Sujetando el portacanillas por la uñeta metálica, introdúzcalo en la lanzadera y suelte el pestillo. Asegúrese de que la uñeta metá- lica del portacanillas se encaje en la hendidura en la parte supe- rior de la anilla tal como se indica en la fig. C.

NOTA:

Si el portacanillas no se encuentra bien colocado en la máquina se saldrá de la lanzadera inmediatamente después de empezar a co- ser.

1Pestillo del portacanillas

2 Uñeta del portacanillas

3 Resorte de tensión

4 Hendidura

Mettre l’interrupteur principal sur “O”.

1.Remonter complètement l’aiguille en tournant le volant vers soi (dans le sens opposé aux aiguilles d’une montre) et relever le levier du pied- de-biche.

2.Ouvrir le couvercle de la navette, derrière la table d’extension, à l’avant de la machine, et retirer le boîtier de la canette en tirant la languette métallique vers soi pour le sortir de la coursière. (fig. A)

3.Dévider environ 10 cm de fil de la canette pleine et insérer la canette dans le boîtier. (Voir fig. B-1.) Faire passer le fil qui dépasse dans la fente, en bas et vers la gauche, comme illustré sur la fig. B-2, jusqu’à ce qu’il s’insère dans l’orifice de sortie sous le ressort de tension (fig. B-3).

4.Tout en tenant le boîtier par le loquet métallique, l’enfoncer à fond dans la navette et relâcher la languette métallique. Bien veiller à ce que la languette métallique du boîtier s’introduise dans l’encoche en haut de la glissière, comme le montre la fig. C ci-dessous.

REMARQUE:

Si le boîtier n’est pas placé correctement, il va s’échapper de la navette dès qu’on commence à coudre.

1Loquet du boîtier

2 Languette du boîtier

3 Ressort tenseur

4 Encoche

25

Image 34
Contents Page Page Important Safety Instructions Conserve Este Manual DE Instrucciones Importantes Consignes DE Securite Connecting Plugs and Main Power / Sewing Light Switch Contents Índice DEL Contenido Conozca SU Máquina DE CoserTable DES Matières Spool pin Bobbin winding assemblyMain power/sewing light switch Stitch length dialElementos Principales Accessories AccesoriosXL5100/PX100 Conexión de los enchufes Connecting PlugsFuncionamiento DE LA Máquina DE Coser RaccordementFoot Controller Main Power and Sewing Light SwitchesInterruptor principal y de luz PedalChecking the Needle Inserting the NeedleInserción de la aguja Comprobación de la agujaChangement de pied-de-biche Cambio del prensatelasChanging the Presser Foot Modelo a presiónPara estabilizar la máquina Converting to Free-Arm StyleConversión en modalidad de brazo Libre Steadying the MachinePattern Selection Dial Distintos MandosSelector de puntadas Sélecteur de modèle de pointRecommended Widths and Lengths for Stitches XL5200/PX200 B-C-D Anchos Y Largos DE Puntadas Recomendados XL5300/PX300XL5200/PX200 1A-B-C-D Longueurs ET Largeurs DE Point Recommandées XL5200/PX200 Point Universel Ourlet Invisible DE Lingerie Selector de largo de puntada Stitch Length DialSélecteur de longueur de point Couture en points élastiques Stretch StitchingPuntada elástica Selección de la puntada elásticaSelector del ancho de puntada Stitch Width DialSélecteur de largeur de point Palanca de retroceso Levier de couture en marche arrièreBobinado de la canilla Enhebrado DE LA MáquinaWinding the Bobbin Remplissage de la canetteEnhebrado inferior Lower ThreadingMise en place du fil inférieur Upper Needle Threading Enhebrado superior de la aguja Mise en place du fil supérieur Fil de l’aiguilleWhen the machine is equipped with a Using the Needle ThreaderNeedle threader Enhebrador Palanca del enhebrador Système Rapide Para sacar el hilo de la canilla Drawing Up Lower ThreadRemontée du fil inférieur Costura con aguja doble Twin-Needle SewingCouture avvec l’aiguille jumelée Lower tension is too loose Thread TensionUpper tension is too loose BobbinTensión de los hilos Tension des filsChart of Sewing FABRICS, Needles and Thread Combinations Tabla DE Combinaciones Entre TEJIDOS, Agujas Y HilosTableau DES Combinaisons TISSU/AIGUILLE/FIL Point droit Straight StitchingPuntadas rectas Para empezar a coserChanging Sewing Directions fig. a Cambio de sentido de costura fig. aPara terminar las costuras fig. B Finishing Sewing fig. BPara retirar el tejido de la máquina Removing the Material From the MachineTopstitching and Stretch Materials Puntadas en derecho y tejidos elásticosPuntadas zigzag Zigzag StitchingPoint zigzag Blindhem Stitching Puntadas invisiblesOurlet invisible de lingerie Shell Tuck Stitching Puntada alforza derefuerzoPoint à coquilles Inserción de gomas elásticas Point élastiqueRemiendos Puntada de uniónPuntada universal Scallop StitchingPuntada festón Universal StitchingOveredge Stitching Puntada por encima de la orillaPoints sur le bord Feather Stitching Puntada plumaPoint plume Decorative Stitching Triple Zigzag Stretch StitchingPuntada triple zigzag elástica Puntada decorativaMaking a Buttonhole Making a ButtonholeMaking a Buttonhole on Stretch Fabrics fig. E Pour coudre une boutonnière Para coser ojales Solo XL5300, XL5200, PX300 y PX200Cosido de ojales en tejidos elásticos fig. E Making a Buttonhole XL5100 and PX100 only Para coser ojales Solo XL5100 y PX100Pasos Parte Cosida Step Sewn Portion Pattern How to SewComo Coser Para Completar las Puntadas y Cortar el Ojal Phase Partie cousue Modèle Comment coudreSecuring the Stitching and Cutting the Buttonhole Comment arrêter la couture et ouvrir la boutonnièreButtonhole Fine Adjustment Ajuste fino de los ojales Equilibrage des boutonnièresButton Sewing Costura de botones Pour coudre un boutonZipper Inserting GatheringInsertion de fermeture à glissière Inserción de cremallerasFruncido Pour froncer un tissuDarning ZurcidoReprisage Appliques AplicacionesAppliques Monogrammes et broderies Monogramming and EmbroideringMonogramas y bordados Preparación para monogramas y bordadosEmbroidering MonogramasBordado MonogrammesChanging the Bulb Remplacement de l’ampouleCambio de la bombilla Oiling EngrasadoGraissage Limpieza CleaningNettoyage Performance Checklist Upper Thread Lower Thread Skipped Loop in Seam FabricFabric does Listado de posibles incidencias Póngase EN Contacto CON EL Servicio Técnico LocalEL Tejido no Arrastra Bien Liste de vérification en cas de défaillances Contacter LE Centre Technique LE Plus ProcheContacter LE Service Technique LE Plus Proche Embalaje de la máquina ImportanteRepacking the Machine Emballage de la machineBobbin Threading Winding Bridging Stitch Buttonhole Sewing Aguja Aiguille Page Page Potencia Consumida 90W English Español

XL5100, XL5300, XL5200 specifications

The Brother XL series sewing machines, including the XL5200, XL5300, and XL5100, are versatile and user-friendly models designed for both beginners and experienced sewers. These machines combine functionality with advanced features to cater to a wide range of sewing projects.

The Brother XL5200 is designed to simplify the sewing experience while offering versatility. It features 35 built-in stitches, including decorative, utility, and stretch stitches, providing plenty of options for various projects. The easy-to-read LCD screen allows users to select stitches effortlessly. One of its standout features is the automatic needle threader, eliminating the frustration of threading the needle manually. The machine also comes equipped with a drop-in top bobbin system that ensures smooth and consistent sewing.

The XL5300 builds upon the capabilities of the XL5200, providing additional features that enhance creativity. With 60 built-in stitches, including an impressive selection of decorative stitches and seven one-step auto-size buttonhole options, this model encourages experimentation. The XL5300 also includes a hard case for protection and portability, making it an excellent choice for sewers who attend classes or workshops. Its adjustable stitch width and length allow for customization of stitches, ensuring the outcome perfectly aligns with the user’s vision.

The Brother XL5100 is a great entry-level machine known for its ease of use. This model contains 50 built-in stitches, including essential utility stitches that are perfect for garment construction, quilting, and crafting. Like its counterparts, it features an automatic needle threader and a jam-resistant drop-in bobbin. The XL5100 also offers a convenient free arm that is ideal for sewing sleeves and cuffs. This model is particularly user-friendly, making it an excellent option for beginners looking to develop their sewing skills.

All three models come with various presser feet and accessories that expand their functionality, such as a zipper foot, buttonhole foot, and walking foot for quilting. They are designed with sturdy construction, ensuring durability and longevity for all sewing enthusiasts.

In summary, the Brother XL5200, XL5300, and XL5100 are excellent choices for those looking for reliable sewing machines that offer a blend of user-friendly features, versatility, and performance. Whether for simple alterations or complex projects, these models provide the tools necessary to help bring user creativity to life.