Henny Penny EEG-143 Electrical Requirements, Motor Bearings Lightingand Shutdown of the Burners

Page 19

2-9. ELECTRICAL REQUIREMENTS (Continued)

2-10. MOTOR BEARINGS

2-11. LIGHTINGAND SHUTDOWN OF THE BURNERS

609

Model EEG-141, 142, 143, 144

To avoid electrical shock, do not disconnect the ground (earth) plug. This fryer must be adequately and safely grounded (earthed). Refer to local electrical codes for correct grounding (earthing) procedures or in absence of local codes, with The National Electrical Code, ANSI/NFPA No.

70-(the current edition). In Canada, all electrical connections are to be made in accordance with CSA C22.2, Canadian Electrical Code Part 1, and/or local codes.

Disconnect power supply before a thorough cleaning or servicing the fryer

The electric motor bearings are permanently lubricated. DO NOT LUBRICATE.

1.Turn the power switch to the OFF position.

2.Wait at least 5 minutes and then turn the power switch to the ON position.

3.Press button on the controls (left or right).

4.The burner lights and operates in a Melt Cycle until the shortening reaches a preset temperature.

6.Once the display shows a product selection or a double dashes, press the desired product button.

The fryer is equipped with a ignition spark module which has a set ignition safety time (TSA) of 90 seconds.

To shutdown burner:

1. Press

button on the controls (left or right).

2.Turn the power switch to the OFF position. NOTE: This turns off all vats.

2-7

Image 19
Contents OPERATOR’S Manual Page FM05-057-C Revised Technical Data for CE Marked Products Limited Warranty for Henny Penny Equipment Table of Contents Section Table of Contents Page Introduction FeaturesProper Care Assistance SafetySafety Page Unpacking InstallationSelecting the Fryer Location Leveling the Fryer GAS Supply GAS Supply GAS Supply Model EEG-141, 142, 143 Motor Bearings Lightingand Shutdown of the Burners Electrical RequirementsDimensions Page Refer to explanations on the next pages Operation Operating ComponentsDescription Operating ComponentsFunction Description Function JIB VAT Type Full or Split SET-UP ModeFill POT from Bulk Filling or Adding OILMorning START-UP Procedures Basic Operation Idle Mode Selectinga Product Withadifferent Setpoint Replacing the JIB OIL Guardian Auto Top-OffFilling Oil Reservoir Removing/Cleaning ReservoirModel EEG-141 OIL ReservoirSmartfilter Express Smartfilter Express Filter ErrorCheck Filter Pan a new filter pad should be used on Daily FilteringDaily Filtering Discarding OIL from VAT Using Optional OIL Discard Shuttle Express FILTER? Changing the Filter PAD Changing the Filter PAD Removing and Cleaning Basket Rest CLEAN-OUT CLEAN-OUT ModeCLEAN-OUT Mode Rinse Complete YES no CHECK/REPLACE Filter Drain PAN O-RINGS Filter Button Stats Actual Oil TemperatureRecovery Information for each Vat Info Button StatsProcedureFrequency Preventive Maintenance ScheduleClean Blower & Vents Page Information Mode Details Information ModeFunction Display EX DetailsTUE NEW OIL Reset usage data Change Product Names Product Program Mode Modifying Product SettingsAssign Button Quality Timer hold time Modifying Product SettingsTo Change Times and Temperatures Alarms 1MixFilterdAfterFil TrackingX Number of Loads Filter Control Level 2 Programming Special Program ModeLanguage SP-2 Special Program ModeAudio Volume SP-4 Degrees Fahrenheit or Celsius SP-1Audio Tone SP-5 Idle Mode Enabled SP-7Liquid or Solid Cooking Oil Used SP-6 Mixed Filter Tracking Mode SP-8If Global is selected, press button GlobalPolish Duration SP-9 Clean-Out Time SP-11Clean-Out Temperature SP-12 Cooking Indicator SP-15Fryer Type SP-19 2nd Volume SP-17Engery Save Mode SP-18 2nd Language SP-16Serial Number Log SP-24 Autolift Enabled SP-21Bulk Oil Supply SP-22 Bulk Oil Disposal SP-23Let User Exit Fill SP-29 Usage Code Change SP-26Dispose Requires Code ? SP-27 Longer Fill Time SP-28Model EEG-141, 142, 143 Problem Cause Correction Troubleshooting Trouble Shooting GuideRemove the right side panel Display Cause Correction Error CodesClosed Error Codes Display Cause CorrectionPage Henny Penny Corporation Box Eaton,OH Toll free in USA