Assembly and Adjustments (continued)
Installing and Adjusting the Guide Bar and Saw Chain (continued)
| WARNING! |
|
|
|
|
|
|
|
| The cutters on the saw |
|
|
|
|
|
|
|
| chain are very sharp! Always wear |
|
|
|
|
|
|
|
| gloves when handling. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5. Install the chain loop over the drive |
|
|
|
|
|
| ||
| sprocket, and then align the chain |
|
| Sprocket |
| |||
| drive links within the guide bar groove. |
|
|
| ||||
|
|
|
|
|
|
| ||
| Verify that the cutters are properly ori- |
|
|
|
|
|
| |
| ented with cutter edges facing forward |
|
|
|
|
|
| |
| on top of bar. If chain installation is dif- |
|
|
|
|
|
| |
| ficult or if the chain appears too tight, |
|
|
|
|
|
| |
| refer to step 8. |
|
| Insert Chain Tensioner Pin | ||||
|
|
|
|
| into the Hole |
| ||
| WARNING! |
|
| Saw Chain | ||||
|
|
|
|
|
| |||
| Never operate this saw |
|
|
|
|
| ||
|
|
|
|
|
|
| ||
| without the clutch cover installed. |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| IMPORTANT! |
|
|
|
|
|
| |
| Proper chain adjustment is essential for |
|
| Chain |
|
|
| |
| maximum performance, chain life, and |
|
| Adjusting |
|
|
| |
|
|
| Screw |
|
|
| ||
| operator safety. Always inspect chain ten- |
|
|
|
|
| ||
|
|
|
|
|
|
| ||
| sion before operating this saw! |
|
| Turn Clockwise to |
|
| 1/8” Max. (3 | |
|
|
|
|
|
|
| ||
|
|
|
|
| ||||
|
|
|
|
| Tighten the Chain |
|
| |
6. Install the clutch cover over the bar |
|
|
|
| - 3.5 mm) | |||
|
| (extend the guide |
|
| ||||
| stud(s) and install the bar nut(s) finger |
|
| bar) |
|
|
| |
| tight. |
|
|
|
|
|
| |
7. Place the saw on a flat surface and lift |
|
|
|
|
|
| ||
| the bar nose slightly. |
|
|
|
|
|
| |
8. To adjust chain tension: |
|
|
|
|
|
| ||
| a. Turn the chain tension screw clock- |
|
|
|
|
| Check the gap between chain side | |
| wise to tighten the chain. |
|
|
|
|
| plates and the bar rail | |
|
|
|
|
|
|
| ||
| b. Turn the chain tension screw coun- |
|
|
|
|
|
| |
| 9. | Tighten the bar nut(s). The saw chain |
| |||||
|
| |||||||
|
|
| tension is correct when there is not any |
| ||||
| c. While lifting the bar nose, tighten or |
|
|
| ||||
|
|
| slack on the bottom of the guide bar |
| ||||
| loosen the adjusting screw until the |
|
| but the saw chain can move freely. |
| |||
| chain at |
|
|
|
|
|
| |
| bar just contacts the guide bar rails. |
|
|
|
|
|
|
Re-Adjusting the Saw Chain
1.To adjust chain tension in the field: Stop the saw and allow the guide bar and chain to cool. Loosen both bar nuts approximately
WARNING!
Inspect chain tension often during operation, especially when breaking in a new chain. A loose saw chain can jump from the guide bar, possibly causing serious per- sonal injury!
8