NAME AND OPERATION
• | For Cooling Only type, , and |
| are not displayed on LCD. |
• | Max. 8 indoor units can be operated by a remote controller. | ||
• | Once setting the operation items, you can operate the previous condition by pushing | ||
| button only. |
|
|
HOW TO OPERATE AIR CONDITIONER
COOL/HEAT AUTO, HEAT, DRY, COOL, FAN
1 Power supply
Turn on the power supply of the air conditioner 12 hours before starting the operation.
<The following display is for explanation, so it differs from the real display.> |
2 Push 
button.
3
Push 
button (
) to select fan
8 9 |
speed.
When selecting AUTO, fan speed is automatically changed.
(During FAN mode, the air speed is not.)
– 150 –
TEST | ˚C |
SETTING | ˚F |
1 | 4 |
| |
2 | 5 |
3 | 6 |
| 7 |
1 Fan Speed button
2 Operation mode button
3 Swing/Air direction button
The flap angle is changed.
10 |
|
| 12 |
TEST | ˚C | 13 | |
SETTING | ˚F | ||
11 |
| 14 | |
|
| ||
|
|
|
15 16
8 Selected mode displays (Heat pump type)
Any one of 
, 
, 
, 
or 
displayed.
While 
is displayed, the indoor fan stops or the mode is Low speed mode.
9 Selected mode displays (Cooling only type)
Any one of 
, 
or 
is displayed.
10
TEST
SETTING
3
˚C 
˚F
4
2
5
4
5
Push either 
or 
set to Auto.
<Recommended temperature>
•During FAN mode, the temperature cannot be set up.
Stop
Push 
button.
When stopping the unit by the remote controller, the fan of the outdoor unit, the fan or the outdoor unit may keep operating for a while even if the compressor of the outdoor unit has stopped.
4 Temperature Setup button
Every pushing 
button, temperature rises by 1˚C.
Every pushing 
button, temperature decrease by 1˚C.
5
[Start/Stop] button
6Check button (Used in servicing)
• Do not use this button usually.
7Remote control temperature sensor Usually controlled by the indoor unit sensor, it can be changed to the remote controller. For details, contact the shop which you purchased the air conditioner. (When using a group control method, do not use the remote controller sensor.)
TEST is displayed during Test Run.
11
(CHECK) is displayed when the protec- tive device worked or trouble occurred.
12
is displayed during the operation.
If the remote controller setting is prohibited by
the central remote controller, 
flashes when [Start/Stop], [Operation Select] or [Temp. Setup] button is pushed and change is not accepted.
13The setup temperature is displayed.
14Warning code is displayed when a trouble occurred.
15Selected fan speed, 
, 
, 
or 
displays.
16
is displayed when the remote controller sensor is used.
•When the unit cannot be stopped by the remote controller.
Turn off the main power switch or the leakage breaker, and then contact the shop which you purchased the unit.
•In heating, if the room is not enough heated with FAN 
, select FAN 
or 
.
•As the temperature sensed by the temp. sensor periphery of the suction port of the indoor unit, it differs from in the room according to the installation state. Set the tempera- ture considering the setup value as the standard temperature in the room.
Automatic Cool/Heat
When all indoor units in the identical refrigerant system are controlled as a group and when all indoor units are installed in the same room, the cooling or heating operation is automati- cally performed with the difference between the setup temperature and the room tempera- ture.
RBC
•When turning on the power switch of the simple operation type remote controller at the first time,
flashes. While 
is displayed, the automatic model check is operating. Operate the remote controller after 
has disappeared.
