Balcar R410A 156, How To Handle The Remote Controller, How To Use The Remote Controller Correctly

– 156 –

HOW TO HANDLE THE REMOTE CONTROLLER

•Direct the transmitter of the remote controller toward the sensor (indoor unit body). When the signal is normally received, “Pi” sound is heard once.

(“Pi, pi” sounds are heard only when the operation has started.)

•The standard distance which the signal can be received is approx. 7m. The distance differs a little according to the capacity of the battery, etc.

•Be careful there is not something to block the signal between the sensor (indoor unit body) and the remote controller.

•Do not put the remote controller on the place exposed to the direct sunlight or air from the air conditioner or near the stove, etc.

•Do not drop, throw, or clean with water the remote controller.

•The signal may be accepted in a room where the electronic instantaneous-ON type or inverter type florescent light is set. For details, contact the shop which you purchased the air conditioner.

To Use the Remote Controller Setting to Wall, etc.

•Check a signal is received correctly by pushing Start/Stop button at the position to be fixed.

•To take off remote controller, pull it toward you.

Fix the remote controller	Setting method of
holder with the screws.	remote controller
	Put on.
Mounting screw	1
Truss tapping

Push.

2

Remote controller holder

HOW TO USE THE REMOTE CONTROLLER CORRECTLY

•Set the remote controller so that it is not excessively far from the sensor

(indoor unit), otherwise a malfunction is caused.

Be sure to set the remote controller in the same room where the sensor (indoor unit) is installed.

•Direct the remote controller toward the sensor (indoor unit) for operation.

When a signalis correctlyreceived, “Pi”soundcan be heard.

•Avoid to set the remote controller at a place where it is covered with curtain, etc.

ADDRESS

When the multiple indoor units corresponding to the wireless remote controller are installed in the same room, an address can be set up to prevent an interference.

Matching the address switch of the sensor with number of the remote controller ad- dress, Max. 6 indoor units can be controlled by the corresponding remote controller individually.

The address switch for receiving the signal is prepared to the sensor (inside of panel or indoor unit) and the address switch for sending the signal is prepared to the remote controller. For details, contact the shop which you purchased the air conditioner.

How to Check the Address

When pushing ADR button on the remote controller, the present address is displayed on the display section of the remote controller. If this address matches with the address of the sensor (inside of panel or indoor unit), a buzzer sounds.

(When ALL is displayed, buzzer sound is necessarily heard.)

When ALL is displayed, the air conditioner can be operated regardless of any address of the sensor (inside of the indoor unit). Send the signal by directing the remote controller toward the sensor (panel or indoor unit body) to be handled.

How to Match the Address

Setup to remote controller address

1.When keeping ADR pushed for 4 seconds or more, ADR lamp goes on at the display section of the remote controller and the present address is displayed with flashing.

2. Every pushing ADR , the address is exchanged as ALL 1 2 3 … 6 ALL. Match one of them with the address switch of the indoor unit sensor to be handled.

3.When pushing C L , the address display goes on and is displayed for 5 seconds.

If the address matches with the address switch of the operation part, the buzzer sounds.

Display of

Address

Address

Address

Address

remote

controller

address

4–6

1–3

Address select

4–6

1–3

Address select

4–6

1–3

Address select

Address switch

* Address switch

S001

S001

S001

position of

of sensor unit

3

2

1

3

2

1

3

2

1

sensor

can be set any

6

5

4

Address

6

5

4

Address

6

5

4

Address

position.

S002

S002

S002

Turn the knob to the right side for 1 to 3 while to the left side for 4 to 6 of Address select switch S001.

RBC-AX22CE