Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 2E43-27R, 2E42-27R manual Port Type Read-only, Link Status Read-only

Models: 2E42-27R 2E43-27R 2E42-27 2E43-27

1 164

Download 164 pages 19.47 Kb

Page 101

High Speed Interface Conﬁguration Screen

The following brieﬂy explains each ﬁeld of the High Speed Interface Conﬁguration screen.

Port Type (Read-only)

Displays the type of interface (FE-100FX, FE-100TX, FE-100F3, or Unknown) installed in ports 25 and 26. Figure 5-22shows that there is an FE-100TX interface installed in port 25 and no interface indicated by Unknown in port 26.

Link Status (Read-only)

Indicates whether or not there is a physical connection from this port to another 10BASE-T or 100BASE-TX/FX device. One of the following values displays:

•Link – There is a link signal present and a valid physical connection to another device.

•No Link – There is no link signal present and no valid physical connection to another device.

Current Oper. Mode (Read-only)

This ﬁeld displays the current operating mode of ports 25 and 26. Depending on whether a 100BASE-FX, or 100BASE-TX is installed, this ﬁeld displays the following:

•With a 100BASE-FX interface: 100Base-FX, 100Base-FXFD (full duplex), or N/A when port is empty.

•With a 100BASE-TX interface: Unknown, 10Base-T, 10Base-TFD (full duplex), 100Base-TX, 100Base-TXFD (full duplex) or N/A when port is empty.

2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide

5-49

Image 101

Cabletron Systems 2E43-27R, 2E42-27R manual Port Type Read-only, Link Status Read-only, Current Oper. Mode Read-only

Contents

9031960-05 2E42-27/2E42-27R/2E43-27/2E43-27R SmartSwitch User’s Guide2E42-27 2E43-27Page 2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide Only qualiﬁed personnel should perform installation proceduresFCC NOTICE VCCI NOTICE INDUSTRY CANADA NOTICECABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT 2E42-27/2E42-27R/2E43-27/2E43-27R User’s GuideCABLETRON SOFTWARE PROGRAM LICENSE EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYUNITED STATES GOVERNMENT RESTRICTED RIGHTS 2E42-27/2E42-27R/2E43-27/2E43-27R User’s GuideSAFETY INFORMATION CLASS 1 LASER TRANSCEIVERS SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERSLASER RADIATION AND CONNECTORS 2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide DECLARATION OF CONFORMITYApplication of Council Directives 89/336/EEC 73/23/EEC Manufacturer’s Name Cabletron Systems, Inc2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide INSTALLATION CONTENTSCHAPTER INTRODUCTIONTROUBLESHOOTING ContentsCHAPTER CHAPTER2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide ContentsSPECIFICATIONS ContentsSPECIFICATIONS OPTIONAL INSTALLATIONS AND1.2 STRUCTURE OF THIS GUIDE 1.1 USING THIS GUIDECHAPTER INTRODUCTION Chapter 1 Introduction 1.3 2E4X-27 FEATURESFull Duplex Switched Ethernet FDSE support for 20 Mbps or 1.4.1 Connectivity 1.4 2E4X-27 OVERVIEW1.4.3 SmartTrunk 1.4.2 Full Duplex Switched Ethernet1.4.5 Management 1.4.4 Runtime IP Address Discovery1.4.9 LANVIEW Diagnostic LEDs 1.4.6 Switching Options1.4.7 Standards Compatibility 1.4.8 Year 2000 CompliantTable 1-1 Fast Ethernet Interface Modules 1.4.10 Optional FeaturesThe following conventions are used throughout this document 1.5 DOCUMENT CONVENTIONSDocument Conventions 2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide1.6 GETTING HELP 1.7 RELATED MANUALS 2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide Chapter 1 Introduction1-12 2.2 10BASE-T NETWORK CHAPTER NETWORK REQUIREMENTS2.1 SmartTrunk 2.4 100BASE-FX FIBER OPTIC NETWORK 2.3 100BASE-TX NETWORKMultimode Mode Fiber Optic Cable Length Single Mode Fiber Cable LengthsCHAPTER INSTALLATION 3.1 UNPACKING THE 2E4X-27 3.2 INSTALLING OPTIONS3.3.1 Tabletop or Shelf Installation 3.3 INSTALLING THE 2E4X-27Guidelines for Tabletop and Shelf Installations InstallationGuidelines for the Rackmount Installation 3.3.2 Rackmount InstallationRack mounting the 2E4X-27 involves the following Proceed as follows to install the 2E4X-27 into a 19-inch rack 3.3.3 Connecting Power to the 2E42-27 or 2E43-27 Figure 3-5 2E42-27R/2E43-27R Rear View 3.3.4 Connecting Power to the 2E42-27R or 2E43-27R3.4.1 Connecting UTP Cables to Ports 1 Through 3.4 CONNECTING TO THE NETWORK3.4.1.1 2E42-27 or 2E42-27R Cable Connections Figure 3-7 Cable Pinouts - RJ45 Crossover Cable 3.4.1.2 2E43-27 or 2E43-27R Cable ConnectionsFigure 3-8 2E43-27 or 2E43-27R Straight Cable Connection Figure 3-9 Connection Using the RJ21 Angle Adapter3.4.2 Connecting a UTP Segment to the FE-100TX 100 FE-100TX Figure 3-10 FE-100TX Crossover SwitchFiber Optic Network Connection 3.4.3 Connecting a Fiber Optic Segment to the FE-100FX and FE-100F3RX LED Figure 3-11 FE-100FX and FE-100F3 Ports3.5 COMPLETING THE INSTALLATION 2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide Chapter 3 Installation3-18 4.1 USING LANVIEW CHAPTER TROUBLESHOOTINGFlashing indicates an LED ﬂashing randomly Chapter 4 TroubleshootingSolid indicates a steady LED light. No ﬂashing 2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide Using LANVIEWTable 4-1 LANVIEW LEDs Continued Color100 LED Receive RX LED 4.2 FE-100TX LEDFE-100TX LED Table 4-3 10/100 LED Indications When RX LED Is OffNo link exists if the associated port 25 or 26 RX Receive LED is off 2E42-27/2E42-27R/2E43-27/2E43-27R User’s GuideChapter 4 Troubleshooting 4.3 TROUBLESHOOTING CHECKLISTTable 4-4 Troubleshooting Checklist Problem2E42-27 4.4 USING THE RESET BUTTONdowntime of up to two minutes will result from this action 2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide Chapter 4 Troubleshooting5.1 OVERVIEW CHAPTER LOCAL MANAGEMENTChapter 5 Local Management 5.2 LOCAL MANAGEMENT KEYBOARD CONVENTIONS2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide Table 5-1 Keyboard Conventions5.3 MANAGEMENT TERMINAL SETUP Figure 5-1 Management Terminal Connection 5.3.1 Console Cable ConnectionManagement Terminal Setup 5.3.2 Management Terminal Setup ParametersTable 5-2 VT Terminal Setup Display Setup MenuFigure 5-2 Uninterruptible Power Supply UPS Connection 5.3.3 Monitoring an Uninterruptible Power SupplyFigure 5-3 The 2E4X-27 Local Management Password Screen 5.4 ACCESSING LOCAL MANAGEMENT5.4.1 Navigating Local Management Screens Figure 5-4 802.1D Switching Mode, LM Screen Hierarchy Accessing Local ManagementFigure 5-5 802.1Q Switching Mode, LM Screen Hierarchy 2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide5.4.3 Exiting Local Management Screens 5.4.2 Selecting Local Management Menu Screen ItemsTo exit LM using the RETURN command, proceed as follows DEVICE CONFIGURATION 5.5 DEVICE MENU SCREENNETWORK TOOLS DEVICE STATISTICS5.6 DEVICE CONFIGURATION MENU SCREEN SWITCH CONFIGURATION GENERAL CONFIGURATIONETHERNET FULL DUPLEX CONFIGURATION SMARTTRUNK CONFIGURATION5.7 GENERAL CONFIGURATION SCREEN Subnet Mask Modiﬁable Default Gateway ModiﬁableTFTP Gateway IP Addr Modiﬁable Device Date ModiﬁableDisplays the total time that the device has been operating 5.7.1 Setting the IP Address 5.7.2 Setting the Subnet Mask Figure 5-11 Conﬁguration Warning Screen 5.7.3 Setting the Default Gateway5.7.4 Setting the TFTP Gateway IP Address 5.7.6 Setting the Device Time 5.7.5 Setting the Device Date5.7.7 Entering a New Screen Refresh Time 5.7.8 Setting the Screen Lockout Time802.1D SWITCHING, 802.1Q SWITCHING, or SECURE FAST VLAN 5.7.9 Setting the Operational Mode5.7.10 Conﬁguring the COM Port If the COM port is reconﬁgured without a valid IP address set General Conﬁguration Screen2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide 5-275.7.10.1 Changing the Com Port Application 5.7.11 Clearing NVRAM 5.7.12 Enabling/Disabling IP Fragmentation Figure 5-15 SNMP Community Names Screen 5.8 SNMP COMMUNITY NAMES SCREEN5.8.1 Establishing Community Names To establish community names, proceed as follows 5.9 SNMP TRAPS SCREEN Enable Traps Toggle 5.9.1 Conﬁguring the Trap Table5.10 SWITCH CONFIGURATION SCREEN Displays the base hardware address assigned to each listed port 5.10.2 Setting the Age Time Field 5.10.1 Setting the STA5.10.3 Setting Enabling or Disabling the Port Status Status ToggleFigure 5-18 Ethernet Full Duplex Conﬁguration Screen 5.11 ETHERNET FULL DUPLEX CONFIGURATION SCREENThis section explains each ﬁeld of the Full Duplex Conﬁguration screen 5.11.1 Setting the Operation Mode 5.12 DEVICE SPECIFIC CONFIGURATION MENU SCREEN Figure 5-19 Device Speciﬁc Conﬁguration Menu Screen HIGH SPEED INTERFACE CONFIGURATIONSYSTEM RESOURCES 802.1Q VLAN CONFIGURATION 5.13 SYSTEM RESOURCES SCREENFLASH DOWNLOAD PORT REDIRECT FUNCTIONThe following brieﬂy explains each ﬁeld of the System Resources screen 5.14 HIGH SPEED INTERFACE CONFIGURATION MENU SCREEN 5.13.1 Setting the Reset Peak Switch UtilizationNVRAM Installed Read-only Current Switch Utilization Read-onlyFigure 5-21 High Speed Interface Conﬁguration Menu Screen FAST ETHERNET INTERFACESHSIM Figure 5-22 High Speed Interface Conﬁguration Screen 5.15 HIGH SPEED INTERFACE CONFIGURATION SCREENCurrent Oper. Mode Read-only Port Type Read-onlyLink Status Read-only Advertised Ability Selectable Desired Oper. Mode Selectable5.15.4 Setting the FE-100TX Operational Mode 5.15.2 Setting the FE-100FX or FE-100F3 Operational Mode5.15.1 Conﬁguring an FE-100FX or FE-100F3 in Port 25 or 5.15.3 Conﬁguring an FE-100TX in Port 25 or5.15.5 Setting the FE-100TX Advertised Ability Figure 5-23 Flash Download Screen 5.16 FLASH DOWNLOAD SCREENThe following brieﬂy explains each ﬁeld of the Flash Download screen 5.16.2 Image File Download Using TFTP 5.16.1 Image File Download Using BootPDownload Server IP Selectable Download File Name SelectableFor example /tftpboot/2E42.hex 5.16.3 Image File Download Using RuntimeFor example /tftpboot/2E42.fls 5.17 PORT REDIRECT FUNCTION SCREEN Shows which ports are currently set as source ports 5.17.2 Changing Source and Destination Ports 5.17.1 Displaying the Source and Destination Entries5.18 BROADCAST SUPPRESSION SCREEN Figure 5-25 Broadcast Suppression/Statistics Screen Time Since Peak Read-OnlyReset Peak Toggle 5.18.1 Setting the Threshold5.18.2 Setting the Reset Peak SWITCH STATISTICS 5.19 DEVICE STATISTICS MENU SCREENSection 5.7.9 provides instructions on setting the operational mode SECURE FAST VLANThe Device Statistics Menu screen displays the following menu items Figure 5-27 Switch Statistics Screen 5.20 SWITCH STATISTICS SCREENChapter 5 Local Management Interface # Read-Only5.21 INTERFACE STATISTICS SCREEN Figure 5-28 Interface Statistics Screen Interface Read-OnlyName Read-Only InOctets Read-Only InErrors Read-OnlyInUnicast Read-Only InNonUnicast Read-OnlyAdmin Status Read-Only OutErrors Read-OnlyOutNonUnicast Read-Only OutDiscards Read-Only5.21.1 Displaying Interface Statistics 5.21.2 Using the Clear Counters Command5.22 RMON STATISTICS SCREEN This ﬁeld displays the name of the entity that conﬁgured this entry Fragments Read-only Oversized Pkts Read-onlyJabbers Read-only Total Packets Read-only5.22.1 Displaying RMON Statistics 5.23 NETWORK TOOLS 5.22.2 Using the Clear Counters CommandThere are two categories of commands in the command set Description SyntaxOptions Example5.23.1 Built-in Commands bridge ENABLE/DISABLE IFNUM/ALL defroute delete interface number IP address delete the default IP route to a managed deviceNetwork Tools defroutenetstat option The netstat command provides a display ofgeneral network statistics for the managed one of the two display optionsThe Network Tools connection to the device will be terminated resetTIP upon execution of this command protocols that are currently supported are ARP not reached, the command displays all next-hoptraceroute IP address routers in the path to the device. If the device isSyntaxsoftreset IP address. The IP address ﬁeld is mandatory The user must specify the remote host using itslinktrap option as enable, disable, or status. The STATE The atmstpstate command allows the user toNetwork Tools atmstpstateChapter 5 Local Management 5.23.2 Special Commandsdone, quit, exit 5-88A.1 DEVICE SPECIFICATIONS APPENDIX A SPECIFICATIONSELECTRICAL SPECIFICATIONS PHYSICAL PROPERTIESAppendix A Speciﬁcations A.4 ENVIRONMENTAL REQUIREMENTSA.5 INPUT/OUTPUT PORTS A.7 REGULATORY COMPLIANCE A.6 COM PORT/PIN ASSIGNMENTS2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide Appendix A SpeciﬁcationsB.1 FE-100TX APPENDIX B FE-100TX, FE-100FX, AND FE-100F3 SPECIFICATIONS2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide B.2 FE-100FXAppendix B FE-100TX, FE-100FX, and FE-100F3 Speciﬁcations FE-100F3 B.3 FE-100F32E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide FE-100F32E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide Appendix B FE-100TX, FE-100FX, and FE-100F3 SpeciﬁcationsAPPENDIX C OPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGS C.2 REMOVING THE CHASSIS COVER C.1 REQUIRED TOOLSThis section describes how to remove the 2E4X-27 chassis cover Appendix C Optional Installations and Mode Switch Bank SettingsTo remove the chassis cover, proceed as follows Figure C-1 Removing the Chassis Cover C.2.1 Setting the Mode SwitchSwitch deﬁnitions and positions are as follows Switch 7 - Clear NVRAM. Changing the position of this switch resets NVRAM on either the next power-up or the next operation of the front panel RESET button. All user-entered parameters, such as the IP address, device names, etc., are reset to the factory default settings. Once the 2E4X-27 resets, you can either use the factory default settings or re-enter your own parameters Installing Optional Fast Ethernet Interface Modules C.3 INSTALLING OPTIONAL FAST ETHERNET INTERFACE MODULESFigure C-3 Fast Ethernet Interface Module Connector Location Connectorsb. Lift and remove the coverplate from the top of the front standoffs 2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide Installing Optional Fast Ethernet Interface Modules2. Remove the screw from the rear standoff. Save the screw 7. Reinstall the cover INDEX Numerics2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide Index-12E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide IndexIndex-2 2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide IndexIndex-3 destination port2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide IndexIndex-4 Uninterruptible Power Supply connection of Unpacking Troubleshooting 4-1 checklistVLAN configuration of Index2E42-27/2E42-27R/2E43-27/2E43-27R User’s Guide IndexIndex-6