MS-18Replacing the Crank Cover | Cateye EC-3600, EC-3700 specification

Applicable Models: EC-1200 EC-1600 EC-3600 EC-3700

MS-18Replacing the Crank Cover

àREMOVAL

1.Remove both right and left pedals. (Fig. 1)

2.Loosen and remove the fixing screw on the surface of the crank cover. The narrow-width area of the crank cover should position in between the frame cover and the crank. (Figs 2 & 3)

àASSEMBLING

1.Pass the crank through the hole on the crank cover, and fix the crank cover onto the frame cover with screws. (Figs. 2 & 3)

2.Set the right and left pedals.

No.15 Wrench

Crank

Pedal

Fig. 1

Recumbent Type

Crank Cover

Fig. 3

Upright Type

Crank Cover

Fig. 2

MS-19Replacing the Crank Cover

Cateye Ergociser Series 1000 Service Manual

55

Image 57

Cateye EC-3600, EC-3700 MS-18Replacing the Crank Cover, MS-19Replacing the Crank Cover, Set the right and left pedals

Contents

Cateye Ergociser Applicable Models EC-1200 EC-1600 EC-3600 EC-3700 Index ServiceManual Applicable Models EC-1200 Flywheelw/o TypeUpright ForParts OfName Name of Parts for Upright Type w/o Flywheel EC-1600 Name of Parts for Upright Type w/ Flywheel Typew FlywheelOfPartsforUpright Name EC-3600 EC-3700 Name of Parts for Recumbent Type OFF ADD Name of Parts for Belt Drive Type EC-3600B/EC-3700B EC-3600B/EC-3700B Circuit Diagram for Automatic Type Cateye Ergociser Circuit Diagram No Display on Control Unit after Power on 1No Display on Control Unit after Power onEC-1200 EC-1600 EC-3600 EC-3700 Check Method of Causes Repair Method Explanation Figures Main unit in accordance with the following procedures 2No Display of Cadence No Display of Pulse Rate Defective ES-3 Replacing the Power Supply Board Printer is not used. Check if the No.4 select switch onNo Printer Operation EC-1600 EC-3700 Check Method of Causes Repair Method No Loading Check of mechanical systems No Loading Check of Electrical Systems Remove the connector CN-1 from the power supply board5No Loading Check of Electrical Systems Section ES-2 Replacing the 5P Cable No Pedal Rotation Locked 6No Pedal Rotation LockedEC-1600 EC-3600 EC-3700 EC-1200 EC-1600 EC-3600 1Unusual Noise Continuous and Increasing1Unusual Noise Flywheel set with new ones 2Unusual Noise Unusual Noise Periodical 3Unusual Noise Noise occurs when the pedal is rotated with a large torque 1Removing the Frame Covers 1Removing the Frame Covers Removing the Frame Covers Remove the frame covers in the following procedures2Removing the Frame Covers Side pedal can be removed by turning it in the clockwise Frame ES-1Replacing the Wiring within 2Replacing the 5P Cable ES-2Replacing the 5P Cable Cable to the frame by using cable holders Control unit. Also, remove the cable connector. FigFrame Covers Cut the cable holders which fix the cable to remove the 5P ES-3Replacing the Power Supply Board ES-3Replacing the PowerSupply Board When the main unit is viewed from the direction as depicted Metal base in the following procedures. FigFrame side Fig , fasten the frame-side nut ES-5Replacing the CDC Sensor ES-5Replacing the CDC Sensor Replacing the Panel Keyboard ES-6Replacing the Panel Keyboard ES-7Replacing the Button Panel ES-7Replacing the Button Panel ES-8Replacing the Printer Replacing the Printer ES-9Adjusting the Printing Darkness ES-9Adjusting the Printing Darkness ES-10Paper Jamming in Printer Paper Jamming in Printer Workload Unit w/o Flywheel MS-1ReplacingEC-1200 Setting on the large gear. Fig Wheel before setting it to the upper part of the large gearAssemble the chain. Chain should first be set on the free Tension to the chain. Fig MS-1Replacing the Workload Unit w/o Flywheel Flywheel MS-2Replacing the Workload UnitÀMounting the Brandnew Workload Unit MS-3Adjusting the Flywheel MS-3Adjusting the FlywheelEC-1600 EC-3600 MS-4Replacing the Chain MS-5Replacing the Free Wheel Set MS-5Replacing the Free Wheel Set MS-6Replacing the Derailleur Set MS-7Replacing the Idler Set MS-7Replacing the Idler Set MS-8Replacing the Crank Set MS-8Replacing the Crank Set Enable the complete setting of the gear. Fig Fasten the crank cap by using a coin, etc. FigShould be adjusted as illustrated in Fig Adjust the clearance between the magnet mounted on 9Replacing the BB Set MS-9Replacing the BB Set MS-10Replacing the Post Spacer MS-10Replacing the Post Spacer MS-11Adjusting the Spacer Spring MS-11Adjusting the Spacer Spring MS-12Replacing the Inner Pipe Spacer MS-12Replacing the Inner Pipe Spacer EC-3600 EC-3700 MS-13Replacing the Vertical Pipe Spacer MS-13Replacing the Vertical Pipe Spacer MS-14Replacing the Leg Cover MS-14Replacing the Leg Cover EC-3600 EC-3700 MS-15Replacing the Caster and Level Adjuster MS-16Replacing the Seat Post Knob MS-16Replacing the Seat Post Knob EC-3600 EC-3700 MS-17Replacing the Lock Pin MS-17Replacing the Lock Pin MS-19Replacing the Crank Cover MS-18Replacing the Crank CoverÀREMOVAL Remove both right and left pedals. Fig Set the right and left pedals MS-19Replacing the Center Cover of Upright Type EC-1200 EC-16001200, remove the cable holder from the handlebar post MS-20Replacing the Center Cover of Recumbent Type MS-21Replacing the Handlebar Grip MS-22Replacing the Printer Cover MS-22Replacing the Printer Cover MS-23Replacing the Paper Cutter MS-23Replacing the Paper Cutter PNR.780-5160 EC-1600/3700 Panel Keybord unit sets List of Genuin Parts Applicable Models EC-1200EC-1600 PNR.781-5520 EC-3600 Crank CoverL,RSet unit sets Unit sets PNR.781-5580 Parts PNR.701-6701 Wireless Heart Rate Senaor Kit TMUnit sets 1000 PNR.000-0000 HR Senaor Belt unit sets List of Genuin Parts Belt Drive Applicable Models EC-1200B EC-1600B EC-3600B EC-3700BUnit sets Unit pieces P8M15-1192 PNR.724-1022 Unit pieces P8M15-1080 List of Genuin Parts Applicable Models EC-1200 EC-1600 EC-3600 EC-3700