List of Genuin Parts Belt Drive | Cateye EC-3700, EC-3600 specs

Applicable Models EC-1200B EC-1600B EC-3600B EC-3700B

Belt Drive

PNR.780-7050

EC-1600B/1200B Workload Unit

PNR.780-7030 Idler A Set

PNR.780-7040 Idler Spring A

PNR.780-7010 Pulley 1-B

PNR.781-5581

EC-3700B/3600B Workload Unit

unit: sets

unit: pieces

unit: pieces

unit: pieces

PNR.780-6990 Pulley 1-A Set	PNR.780-7020 Pulley 2-A Set	PNR.780-7000 Pulley Flange	PNR.724-1021	EC-1600B/1200B Teethed Timing Belt
unit: sets	unit: sets	unit: pieces		(P8M15-1192)
			PNR.724-1022	EC-3700B/3600B Teethed Timing Belt
			unit: pieces	(P8M15-1080)
			unit: pieces

List of Genuin Parts (Belt Drive)

Cateye Ergociser Series 1000 Service Manual

66

Image 68

Cateye Applicable Models EC-1200B EC-1600B EC-3600B EC-3700B, List of Genuin Parts Belt Drive, Unit pieces P8M15-1080

Contents

Cateye Ergociser Index Applicable Models EC-1200 EC-1600 EC-3600 EC-3700 ServiceManual Flywheelw/o TypeUpright ForParts OfName Applicable Models EC-1200 Name of Parts for Upright Type w/o Flywheel Name of Parts for Upright Type w/ Flywheel EC-1600 Flywheel TypewOfPartsforUpright Name Name of Parts for Recumbent Type EC-3600 EC-3700 OFF Name of Parts for Belt Drive Type ADD EC-3600B/EC-3700B EC-3600B/EC-3700B Circuit Diagram Circuit Diagram for Automatic Type Cateye Ergociser EC-1200 EC-1600 EC-3600 EC-3700 No Display on Control Unit after Power on1No Display on Control Unit after Power on Main unit in accordance with the following procedures Check Method of Causes Repair Method Explanation Figures 2No Display of Cadence No Display of Pulse Rate Printer is not used. Check if the No.4 select switch on Defective ES-3 Replacing the Power Supply BoardNo Printer Operation EC-1600 EC-3700 No Loading Check of mechanical systems Check Method of Causes Repair Method Remove the connector CN-1 from the power supply board No Loading Check of Electrical Systems5No Loading Check of Electrical Systems Section ES-2 Replacing the 5P Cable EC-1600 EC-3600 EC-3700 No Pedal Rotation Locked6No Pedal Rotation Locked 1Unusual Noise Continuous and Increasing EC-1200 EC-1600 EC-36001Unusual Noise Flywheel set with new ones Unusual Noise Periodical 2Unusual Noise Noise occurs when the pedal is rotated with a large torque 3Unusual Noise 1Removing the Frame Covers 1Removing the Frame Covers Remove the frame covers in the following procedures Removing the Frame Covers2Removing the Frame Covers Side pedal can be removed by turning it in the clockwise ES-1Replacing the Wiring within Frame ES-2Replacing the 5P Cable 2Replacing the 5P Cable Control unit. Also, remove the cable connector. Fig Cable to the frame by using cable holdersFrame Covers Cut the cable holders which fix the cable to remove the 5P Supply Board ES-3Replacing the Power Supply BoardES-3Replacing the Power Metal base in the following procedures. Fig When the main unit is viewed from the direction as depictedFrame side Fig , fasten the frame-side nut ES-5Replacing the CDC Sensor ES-5Replacing the CDC Sensor ES-6Replacing the Panel Keyboard Replacing the Panel Keyboard ES-7Replacing the Button Panel ES-7Replacing the Button Panel Replacing the Printer ES-8Replacing the Printer ES-9Adjusting the Printing Darkness ES-9Adjusting the Printing Darkness Paper Jamming in Printer ES-10Paper Jamming in Printer EC-1200 Workload Unit w/o FlywheelMS-1Replacing Wheel before setting it to the upper part of the large gear Setting on the large gear. FigAssemble the chain. Chain should first be set on the free Tension to the chain. Fig MS-1Replacing the Workload Unit w/o Flywheel ÀMounting the Brandnew Workload Unit FlywheelMS-2Replacing the Workload Unit EC-1600 EC-3600 MS-3Adjusting the FlywheelMS-3Adjusting the Flywheel MS-4Replacing the Chain MS-5Replacing the Free Wheel Set MS-5Replacing the Free Wheel Set MS-6Replacing the Derailleur Set MS-7Replacing the Idler Set MS-7Replacing the Idler Set MS-8Replacing the Crank Set MS-8Replacing the Crank Set Fasten the crank cap by using a coin, etc. Fig Enable the complete setting of the gear. FigShould be adjusted as illustrated in Fig Adjust the clearance between the magnet mounted on MS-9Replacing the BB Set 9Replacing the BB Set MS-10Replacing the Post Spacer MS-10Replacing the Post Spacer MS-11Adjusting the Spacer Spring MS-11Adjusting the Spacer Spring MS-12Replacing the Inner Pipe Spacer MS-12Replacing the Inner Pipe Spacer MS-13Replacing the Vertical Pipe Spacer EC-3600 EC-3700 MS-13Replacing the Vertical Pipe Spacer MS-14Replacing the Leg Cover MS-14Replacing the Leg Cover EC-3600 EC-3700 MS-15Replacing the Caster and Level Adjuster MS-16Replacing the Seat Post Knob MS-16Replacing the Seat Post Knob MS-17Replacing the Lock Pin EC-3600 EC-3700 MS-17Replacing the Lock Pin MS-18Replacing the Crank Cover MS-19Replacing the Crank CoverÀREMOVAL Remove both right and left pedals. Fig Set the right and left pedals 1200, remove the cable holder from the handlebar post MS-19Replacing the Center Cover of Upright TypeEC-1200 EC-1600 MS-20Replacing the Center Cover of Recumbent Type MS-21Replacing the Handlebar Grip MS-22Replacing the Printer Cover MS-22Replacing the Printer Cover MS-23Replacing the Paper Cutter MS-23Replacing the Paper Cutter List of Genuin Parts PNR.780-5160 EC-1600/3700 Panel Keybord unit sets Applicable Models EC-1200EC-1600 PNR.781-5520 EC-3600 Crank CoverL,RSet unit sets Unit sets PNR.781-5580 PNR.701-6701 Wireless Heart Rate Senaor Kit TM PartsUnit sets 1000 PNR.000-0000 HR Senaor Belt unit sets Applicable Models EC-1200B EC-1600B EC-3600B EC-3700B List of Genuin Parts Belt DriveUnit sets Unit pieces P8M15-1192 PNR.724-1022 Unit pieces P8M15-1080 List of Genuin Parts Applicable Models EC-1200 EC-1600 EC-3600 EC-3700