General Requirements, Air Flow | Emerson 4015 specs

IM584000300	Installation Instructions
Issue AB, April 3, 2013	Spec. No. 584000300 (Model 4015-X003)

CHAPTER 2.

INSTALLING THE SYSTEM

The individual components of the DC Power System may be shipped as a complete solution factory installed and wired in an IT rack, or may be shipped separately to be installed in a customer provided IT rack.

GENERAL REQUIREMENTS

This product is intended only for installation in a restricted access location on or above a non-combustible surface.

Front and rear access is required for installation.

Required minimum spacing from the rear of the power and control sub-rack to a wall or other solid surface is thirty-six (36) inches for proper ventilation of system components. Required minimum spacing from the rear of the load distribution sub- rack to a wall or other solid surface is twelve (12) inches for proper ventilation of system components.

See Figure 2-1for an air flow diagram.

Hot Aisle

Cold Aisle

Air Flow

Notes:
1. Do not block
air intake openings.	Front

Figure 2-1

Air Flow Diagram

Page 8

Chapter 2. Installing the System

This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy

Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.

Image 18

Emerson 4015 installation instructions General Requirements, Air Flow Diagram Installing the System

Contents

Installation Instructions IM584000300 Issue AB, April 3Page Table of Contents Issue AB, April 3 Spec. No Model Voltages General SafetyImportant Safety Instructions AC Input Voltages DC Input/Output Voltages Battery if Equipped Personal Protective Equipment PPE Circuit Card Handling Maintenance and Servicing ProceduresDual Hazardous Input Power Sources General Static Warning IM584000300 System Packaging Bound System Installation ManualCustomer Documentation Package USB Drive with All Customer Documentation General Part Number Qty Power and Control Sub-Rack List 11Temperature Probes List 98 Part Number Qty Rectifiers Part Number Qty DC Load Distribution Sub-Rack List 21, 22, 23 Battery Tray List 91 Recommended Tools and Test Equipment Installation Acceptance Checklist Checklist -Factory Integrated System List R1, R2General Checklist Customer Integrated System ship loose Air Flow Diagram Installing the System General RequirementsAir Flow Securing the IT Rack to the Floor Inspecting the Equipment Storing for Delayed InstallationsStoring for Delayed Installation Inspecting the Equipment For customer provided IT rack installation only Installing Individual SUB-RACKS Into CutomerInstalling the Sub-Racks Customer Supplied IT Rack Guidelines IM584000300 Electrically Interconnecting the Sub-Racks Mounting Details Torque Important Safety Instructions Wiring ConsiderationsOutput Ground Configurations Cable Routing Sub-Rack IM584000300 Removable Panel Grounding Hrmg Configurations Only Bus Grounding ConnectionTasks to be Performed for Customer Integrated Systems Sub-Rack Grounding Frame Ground Issue AB, April 3 Spec. No Model Load Distribution Sub-Rack Battery Tray Load Distribution Sub-Rack Power and Control Sub-Rack Sub-Racks Electrical Interconnections Sub-Rack Interconnections Making Electrical Connections Power and Control Sub-Rack Battery Tray Tasks to be Perform for ALL Installations IT Rack Grounding Frame GroundConduit Grounding Frame Ground Grounding Scheme Diagram Hrmg System GroundingNPG System Grounding Suggested AC Input Power Connections AC Input Power Connections Making Electrical Connections Hrmg High Resistance Midpoint Ground Configuration NPG Negative Pole Ground Configuration Load Distribution Sub-Rack Battery Manufacturer Information Installing Battery Sub-TraysRefer to -12as this procedure is performed Battery Sub-Trays External Battery Connections if required External Battery Connections Making Electrical Connections Customer Connection To External Battery Strings Digital Inputs IB2 ACU+ Controller Interface Board Connections if requiredDigital Inputs and Programmable Relay Outputs Programmable Relay Outputs Installation Instructions Issue AB, April 3 Spec. No Model Temperature ProbesACU+ Controller Ethernet Connection if required Power and Control Sub-Rack Programmable J6-4 None J6-2 J7-5 J6-5J6-3 None J6-1 J6-6 J7-3 None J7-1 J7-6 Power and Control Chapter Installing the Rectifier Module Initial Startup Preparation Circuit Breaker Locations Initially Starting the System Initially Starting the System ACU+ Controller Local Indicators and Navigation Keys ACU+ Controller InitializationVersion ***** Starting… IM584000300 Verifying the Configuration File Changing Battery Capacity Rating in the ACU+ To Enter a Password Checking Basic System SettingsProcedure To Select a Sub-Menu To Change a ParameterPage Configuring the ACU+ Identification of Rectifiers Checking the System Shutdown Circuit Checking System Status Final Steps Reference Documents Change Issue Number Description of Change ECO NetPerform Optimization Services For More Information