Battery Sub-Trays | Emerson 4015 specification

IM584000300	Installation Instructions
Issue AB, April 3, 2013	Spec. No. 584000300 (Model 4015-X003)

Battery Tray

Note: Battery tray must be installed in rack before installing batteries.

Battery tray output cables not shown for clarity.

Battery

Retaining

Bracket

X

On the sub-trays that hold five (5) batteries, one battery string cable is disconnected and sleeved at the factory. Locate this lead and connect

it to the open battery terminal in that tray.

Battery Sub-Trays

If a battery temperature probe

is to be used, it is recommended to secure it on top of a battery block near this location.

Battery Tray

Battery wiring connectorized for easy installation.

Battery Sub-Tray Connector

Battery Tray Connector

Rear

Figure 3-12

Installing Battery Sub-Trays in List 91 and 92 Battery Tray(s)

Page 32

Chapter 3. Making Electrical Connections

This document is property of Emerson Network Power, Energy Systems, North America, Inc. and contains confidential and proprietary information owned by Emerson Network Power, Energy

Systems, North America, Inc. Any copying, use, or disclosure of it without the written permission of Emerson Network Power, Energy Systems, North America, Inc. is strictly prohibited.

Image 42

Emerson 4015 installation instructions Battery Sub-Trays

Contents

Installation Instructions IM584000300 Issue AB, April 3Page Table of Contents Issue AB, April 3 Spec. No Model Voltages General SafetyImportant Safety Instructions AC Input Voltages DC Input/Output Voltages Battery if Equipped Personal Protective Equipment PPE Circuit Card Handling Maintenance and Servicing ProceduresDual Hazardous Input Power Sources General Static Warning IM584000300 System Packaging Bound System Installation ManualCustomer Documentation Package USB Drive with All Customer Documentation General Part Number Qty Power and Control Sub-Rack List 11Temperature Probes List 98 Part Number Qty Rectifiers Part Number Qty DC Load Distribution Sub-Rack List 21, 22, 23 Battery Tray List 91 Recommended Tools and Test Equipment Installation Acceptance Checklist Checklist -Factory Integrated System List R1, R2General Checklist Customer Integrated System ship loose Air Flow Diagram Installing the System General RequirementsAir Flow Securing the IT Rack to the Floor Inspecting the Equipment Storing for Delayed InstallationsStoring for Delayed Installation Inspecting the Equipment For customer provided IT rack installation only Installing Individual SUB-RACKS Into CutomerInstalling the Sub-Racks Customer Supplied IT Rack Guidelines IM584000300 Electrically Interconnecting the Sub-Racks Mounting Details Torque Important Safety Instructions Wiring ConsiderationsOutput Ground Configurations Cable Routing Sub-Rack IM584000300 Removable Panel Grounding Hrmg Configurations Only Bus Grounding ConnectionTasks to be Performed for Customer Integrated Systems Sub-Rack Grounding Frame Ground Issue AB, April 3 Spec. No Model Load Distribution Sub-Rack Battery Tray Load Distribution Sub-Rack Power and Control Sub-Rack Sub-Racks Electrical Interconnections Sub-Rack Interconnections Making Electrical Connections Power and Control Sub-Rack Battery Tray Tasks to be Perform for ALL Installations IT Rack Grounding Frame GroundConduit Grounding Frame Ground Grounding Scheme Diagram Hrmg System GroundingNPG System Grounding Suggested AC Input Power Connections AC Input Power Connections Making Electrical Connections Hrmg High Resistance Midpoint Ground Configuration NPG Negative Pole Ground Configuration Load Distribution Sub-Rack Battery Manufacturer Information Installing Battery Sub-TraysRefer to -12as this procedure is performed Battery Sub-Trays External Battery Connections if required External Battery Connections Making Electrical Connections Customer Connection To External Battery Strings Digital Inputs IB2 ACU+ Controller Interface Board Connections if requiredDigital Inputs and Programmable Relay Outputs Programmable Relay Outputs Installation Instructions Issue AB, April 3 Spec. No Model Temperature ProbesACU+ Controller Ethernet Connection if required Power and Control Sub-Rack Programmable J6-4 None J6-2 J7-5 J6-5J6-3 None J6-1 J6-6 J7-3 None J7-1 J7-6 Power and Control Chapter Installing the Rectifier Module Initial Startup Preparation Circuit Breaker Locations Initially Starting the System Initially Starting the System ACU+ Controller Local Indicators and Navigation Keys ACU+ Controller InitializationVersion ***** Starting… IM584000300 Verifying the Configuration File Changing Battery Capacity Rating in the ACU+ To Enter a Password Checking Basic System SettingsProcedure To Select a Sub-Menu To Change a ParameterPage Configuring the ACU+ Identification of Rectifiers Checking the System Shutdown Circuit Checking System Status Final Steps Reference Documents Change Issue Number Description of Change ECO NetPerform Optimization Services For More Information