Enterasys Networks X16-C Installing the DIMMs

Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit

3-36 Matrix X16-C Chassis Setup

4. PushtheconnectorarmsawayfromthefirstDIMM,asshowninFigure3‐32,andremovethe

DIMM.

Figure 3-32 Removing the Existing DIMM

5. Repeatstep4toremovethesecondDIMM.

Installing the DIMMs

ToinstalltheDIMMs,proceedasfollows:

1. Makesureconnectorarmsarepushedout.

2. InsertthefirstDIMMdownbetweentheconnectorfingers.

3. PushdownontheDIMMandpushinontheconnectorarmsuntilthearmslockintothetop

notch.

4. Repeatsteps1through3toinstallthesecondDIMM.

1DIMM 2Connector fingers 3 Connector arms

Caution: Observe all Electrostatic Discharge (ESD) precautions when handling sensitive

electronic equipment.

Precaución: Al trabajar con equipos electrónicos sensibles, tome todas las precauciones de

seguridad para evitar descargas de electricidad estática.

Contents

Main Page Notice Regulatory Compliance Information Page Supplement to Product Instructions 50 VCCI Notice BSMI EMC Statement Taiwan Safety Information Class 1 Laser Transceivers Declaration of Conformity Enterasys Networks, Inc. Firmware License Agreement Page Page Page Contents About This Guide Chapter 1: Overview Chapter 2: Site and Configuration Guidelines Chapter 3: Matrix X16-C Chassis Setup Appendix A: Specifications and Regulatory Compliance Index Figures Tables About This Guide Who Should Use This Guide Using This Guide Using the Matrix X Router Manual Set Conventions Used in This Guide Commonly Used Acronyms Getting Help Page Overview System Description Page System Description Matrix X16-C Chassis Installation Guide 1-3 Figure 1-2 Matrix X16-C Chassis as Shipped (Rear View) 1AC power supply inlets (6) with cord lock brackets 2Earth grounding holes Features X16-C Input/Output Modules X16-C Control Module Installing Redundant CMs into an Active Matrix X Router Page Proper CM Recovery X16-C Fabric Module X16-C Redundant Power Supplies Power Supply LEDs Auto-Ranging Power Supplies Power Supply Replacement X16-C Cooling System Page Page Site and Configuration Guidelines Site Guidelines Configuration Guidelines Matrix X16-C Chassis Setup Required Tools Unpacking the Matrix X16-C Chassis Page Page Setting Up the Matrix X16-C Chassis Setup Order Installing the Matrix X16-C Chassis Installing Optional Rack Support Brackets Installing Optional Mid-Mount Brackets Setting Up the Matrix X16-C Chassis 3-8 Matrix X16-C Chassis Setup Figure 3-6 Fastening Mid-Mount Brackets 1Mid-mount brackets (2) 2Bracket screws (30) 2 2 Rack Mounting the Matrix X16-C Chassis Setting Up the Matrix X16-C Chassis 3-10 Matrix X16-C Chassis Setup Figure 3-7 Rack Mounting the Matrix X16-C Chassis S/N: MAC ADD. Chassis Bonding and Grounding 14 4 Attaching the Electrostatic Discharge Wrist Strap Installing and Removing a Power Supply CM1 CM2 Power Supply Planning Installing a Power Supply Page Page Removing a Power Supply Installing and Removing a Fan Tray Installing a Fan Tray 3 3 Removing a Fan Tray Installing and Removing Modules Installing and Removing IOMs Page 235 234 1 3 Installing and Removing CMs Replacing the CM Battery Installing and Removing Modules Matrix X16-C Chassis Installation Guide 3-25 Installing and Removing FMs GROUND S/N: MAC ADD. STRAP FM1 FM2 Attaching Cables, Installing Compact Flash Card and DIMM Upgrade Kit Installing an XFP/SFP Module Removing an XFP/SFP Module Connecting Fiber-Optic Cables LC MT-RJ Connecting to the CM COM Port Connecting the CM COM Port to an IBM PC or Compatible Device Connecting the CM COM Port to a VT Series Terminal 34 1 Connecting the CM COM Port to a Modem 34 1 Figure 3-28 Connecting to a Modem Adapter Wiring and Signal Assignments 5 34 16 Connecting to the CM USB Port Installing a Compact Flash Card Installing the Memory Upgrade Kit Removing the DIMMs Installing the DIMMs Optional Cable Management Kit Installing the Optional Cable Management Kit Page Figure 3-34 Securing Cables Using Velcro Cable Straps Powering Up the Matrix X16-C Chassis LEDs and Reset Button Power Supply LEDs LEDs and Reset Button Matrix X16-C Chassis Installation Guide 3-43 Fan Tray LEDs S/ . 2 GROUND Module LEDs and Reset Button Control and Fabric Module LEDs Figure 3-40 Fabric and Control Module LEDs and Reset Button Table 3-3 Control and Fabric Module LED Definitions IOM LEDs First-Time Quick Configuration Assigning an IP Address to eth0 Configuring DHCP Enabling NTP Naming the Matrix X16-C A Specifications and Regulatory Compliance Chassis, Power Supply, and Fan Tray Specifications Power Supply Requirements, Specifications, and Twist Lock Options Table A-3 Module Power Specifications Table A-4 Redundancy Configurations for AC Line 100120 Vac Table A-5 Redundancy Configurations for AC Line 200240 Vac 10-Gigabit Ethernet Transceiver Specifications (XFP) 1-Gigabit Ethernet Transceiver Specifications (SFP) SFP Input/Output Specifications MGBIC-LC01/MGBIC-MT01 Specifications (1000BASE-SX) MGBIC-LC03 Specifications (1000BASE-SX) MGBIC-LC09 Specifications (1000BASE-LX) Table A-13 MGBIC-LC03 Optical Specifications Table A-14 MGBIC-LC03 Operating Range Table A-15 MGBIC-LC09 Optical Specifications MGBIC-08 Specifications (1000BASE-ELX) MGBIC-02 Specifications (1000BASE-T) Table A-17 MGBIC-08 Optical Specifications Table A-18 MGBIC-08 Operating Range Table A-19 MGBIC-02 Specifications COM Port Pinout Assignments Regulatory Compliance Page Index Numerics A B C G H I L M O P R S T