Extron electronic DVS 304 manual Input Configuration, Start Auto Image Menu

Start Auto Image

Auto image an input to “auto size” and “auto center” the image to fill the screen. The processor measures the sync frequencies from incoming video sources and uses an internal table to set the active image area, total image area, and the sampling frequency.

If an unknown input is connected to the unit, the processor measures and estimates the resolution of the incoming video.

The DVS 304 can be set to automatically auto-image newly detected inputs (see page 21).

Default Cycle

2 sec.

INPUT 1	2 sec.	OUTPUT	MENU
COMPOSITE		1024 x 768@60
			NEXT

START AUTO IMAGE ON IN1

PRESS NEXT TO START

NEXT

Figure 11. Start Auto Image Menu

NOTE: An input with a vertical refresh rate less than 40 Hz will have to be manually

centered and sized, using H/V Start and H/V Active under the Input Config

menu. When a rate with a low vertical refresh rate (for example 720p, 29.9 Hz) is applied and an auto image command is issued, the DVS refers to default

values instead of performing a true auto image.

Input Configuration

START AUTO IMAGE ON IN1

MENU

The following flowchart provides an overview of the Input Configuration submenus and the options for each setting.

Displays only when applicable Displays only when applicable

INPUT

CONFIG

NOTE: Input 1 can only accept composite video. Input 3 can only accept S-video. Only Inputs 2 and 4 can be configured for different video types, although an SDI input can be assigned to any input.

NEXT	INPUT 2
	YUVi
	Select video format

•Composite

•S-video

•YUVi

•YUVp/HDTV

•YUV Auto

NEXT	INPUT 4
	RGB SCALED
	Select video format

•Composite

•S-video

•RGBcvS

•YUVi

•YUVp/HDTV

•RGB scaled

•RGB pass*

•Auto detect

NEXT

SDI INPUT	NEXT	SDI DE-INTER	NEXT
<*> 1 2 3 4		FIELD STNDRD

SDI De-interlacing options:

• Field Standard

• Field Flip

Assign SDI to Input #

• 1, 2, 3, 4, * (none)

NOTE: The SDI input signal can be assigned to any input. Once assigned to a specific input, only an SDI signal can be accepted on that input. SDI can be

ASPECT RATIO

4x3

Aspect ratio options

•4 x 3

•16 x 9

		NOTE: * RGB pass through is only
		available on analog outputs.
DVS 304 DVI models only
Displays only on Input 4	Displays only when applicable

disabled by selecting the *.

Displays only when applicable

NEXT	VGA EDID	NEXT
	1024x768@60

EDID Emulation Specify the resolution and refresh rate.

NOTE: See table in the “Resolutions

and Refresh Rates” section, for EDID values.

FILM MODE	NEXT	H ACTIVE V		NEXT	H START	V	NEXT	TTLPIX PHASE		NEXT
<OFF> ON		XXX	XXX		50	33		XXXX	08
									For YUVp or RGB input only
Film mode	Horizontal active		Vertical active		Horizontal start	Vertical start		Total pixels	Pixel phase
Turn On or Off for low	pixels		lines		Select for the	Select for the		Specify the width	Adjust the pixel
resolution devices.	Specify the width		Specify the		left edge of the	top edge of the		in pixels of the	sampling point for
NOTE: Not for use with	in pixels of the		height in lines of		active video.	active video.		total image area	a selected input.
	active image area		the active image					sampled.
YUVp or RGB inputs.
	sampled.		area sampled.

Figure 13. Input Configuration Menu

NOTE: Only inputs 2 and 4 offer selectable video types. From the Input Configuration

menu, pressing the Next key successively displays submenus with the input

video types for Inputs 2 and 4. The SDI input (where applicable) can be assigned

to any input from the Input Configuration menu.

DVS 304 Series • Operation 12