IP Configuration
The IP Configuration menu displays the IP address of the unit, the Subnet mask, and Gateway IP address.
MEMORY PRESETS
MENU
IP
CONFIG
NEXT |
|
| I 196.168 |
|
|
| P 254.254 |
| |
|
|
|
| |
|
|
|
|
|
View IP address of the unit.
NEXT
S255.255 M 000.000
View the subnet mask of the unit.
NEXT |
|
| G 000.000 |
| NEXT |
|
| M 000.000 |
| ||
|
|
|
|
| |
|
|
|
|
|
|
View gateway IP address of the unit.
Figure 19. IP Configuration Menu
To change an IP address, do the following:
1.Press and hold the Input 4 and Next buttons simultaneously for 2 seconds. This introduces the IP Setup mode.
2.Change the flashing octet selection by using the Adjust vertical ({) knob. Change the address by using Adjust horizontal ([) knob.
3.Press the Next button to select another address to set up (subnet mask or gateway IP).
4.Press the Menu button to save and exit.
The IP configuration menu “times out” and saves changes if there is no activity for over 10 seconds.
Advanced Configuration
The following flowchart provides an overview of the Advanced Configuration submenus and the options for each setting.
IP
CONFIG
MENU
NEXT
ASPECT MODE
FOLLOW
ADVANCED | NEXT | AUTO IMAGE | NEXT | BLUE MODE | NEXT | |
CONFIG | <OFF> ON | <OFF> ON | ||||
|
|
| ||||
Aspect Mode |
|
|
|
|
| |
Sets if an input signal’s |
|
|
|
|
| |
aspect ratio is followed, or |
|
|
|
| ||
if all inputs fill the entire |
|
|
|
| ||
AUTO SWITCH |
| NEXT |
|
| RGB DELAY |
| NEXT | |
<OFF> | ON |
|
|
| 0.0 sec. |
| ||
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
NEXT
ouptut raster. |
| Auto imaging |
| Blue mode |
| |
• Fill |
| When auto image is on, |
| When set to on, only the |
| |
| the unit automatically |
|
| |||
|
| sync and blue video |
| |||
• Follow |
|
|
| |||
| sizes and centers each |
|
| |||
|
| signals are passed to the |
| |||
|
| new input. |
|
| ||
|
|
| display. |
| ||
|
|
|
|
| ||
AUTO MEMORY | NEXT | REFRESH LOCK | NEXT | ENHANCE MODE | NEXT | |
<OFF> ON | <OFF> ON | <OFF> ON | ||||
|
|
| ||||
Auto Memory |
| Refresh Lock |
| Enhance Mode |
| |
When set to on, the unit |
| When set to On, the |
| When set to On, the |
| |
automatically saves the |
| vertical ouptut rate locks |
| automatic gain control of |
| |
input and picture control |
| on to the incoming |
| the low resolution inputs |
| |
settings for each input. |
| vertical refresh rate. |
| is enabled. |
|
Auto switching
The unit switches to the highest numbered input that has a signal present when auto switching is on.
TEST PATTERN |
|
| NEXT |
OFF |
|
| |
|
|
| |
|
|
|
|
Test patterns
•Off
•Crop
•Alternating pixels
•Color bars
RGB delay
Can be set from 0 to 5.0 seconds in 0.5 second steps.
OSD LABEL
2 sec.
On Screen Display label duration
Can be set from 0 OFF (no OSD) to 5 seconds in 1 second steps.
Figure 20. Advanced Configuration Menu
DVS 304 Series • Operation | 18 |
