System snmp community, Config hosts | Fortinet Version 3.0 instruction


config CLI commands	system snmp community

system snmp community

Use this command to configure SNMP communities. Add SNMP communities so that the FortiBridge unit can send SNMP v1 and v2c traps to SNMP managers when action on failure is set to send SNMP traps. You can add up to three SNMP communities. Each community can have a different configuration for SNMP traps. You can also the add IP addresses of up to 8 SNMP managers to each community.

Command syntax pattern

config system snmp community edit <id_integer>

set <keyword> <variable>

end

config system snmp community edit <id_integer>

unset <keyword>

end

config system snmp community

delete <id_integer> end

get system snmp community [<id_integer>]

show system snmp community [<id_integer>]

The config system snmp community command has one subcommand.

config hosts

Keywords and variables	Description	Default

name <name_str>	The name of the SNMP community.	No default.
status {disable enable}	Enable or disable the SNMP community.	enable
trap_v1_lport	SNMP v1 local port number used for sending traps to the	162
<local-port_integer>	SNMP managers added to this SNMP community.
trap_v1_rport	SNMP v1 remote port number used for sending traps to the	162
<remote-port_integer>	SNMP managers added to this SNMP community.
trap_v1_status {disable	Enable or disable SNMP v1 traps for this SNMP community.	enable
enable}
trap_v2c_lport	SNMP v2c local port number used for sending traps to the	162
<local-port_integer>	SNMP managers added to this SNMP community.
trap_v2c_rport	SNMP v2c remote port number used for sending traps to the	162
<remote-port_integer>	SNMP managers added to this SNMP community.
trap_v2c_status {disable	Enable or disable SNMP v2c traps for this SNMP community.	enable
enable}

config hosts

Access the hosts subcommand using the snmp community command. Use this command to add SNMP manager IP addresses to an SNMP community.

FortiBridge Version 3.0 Administration Guide	71
09-30000-0163-20061109

Image 71

Fortinet Version 3.0 manual System snmp community, Config hosts

Contents

M i n i s t r a t i o n G u i d e Regulatory compliance Trademarks Contents Config CLI commands Configuration and operating proceduresUsing the CLI Index Execute CLI commandsPage About this document About FortiBridge Fortinet Knowledge Center Customer service and technical supportFortinet documentation Fortinet tools and documentation CD Example FortiBridge application FortiBridge operating principles Connecting the FortiBridge-1000 copper gigabit ethernet Connecting the FortiBridge unit How the FortiBridge unit monitors the FortiGate unit Normal mode operationConnecting the FortiBridge-1000F fiber gigabit ethernet Probes and FortiGate firewall policies Normal mode operation Probe interval and probe threshold Enabling probes to detect FortiGate hardware failureEnabling probes to detect FortiGate software failure FortiBridge power failure Bypass mode operation Example FortiGate HA cluster FortiBridge application Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces FortiBridge unit basic information FortiBridge-1000 Package contents Mounting instructions FortiBridge-1000F Package contents LED indicators Technical specifications Factory default configuration Connectors Connecting and turning on the FortiBridge-1000 unit Connecting and turning on the FortiBridge unit To connect and turn on the FortiBridge-1000F unit Connecting and turning on the FortiBridge-1000F unitTo connect and turn on the FortiBridge-1000 unit To connect to the FortiBridge console for the first time Connecting to the command line interface CLIConnecting to the FortiBridge console FortiBridge-1000 login Welcome FortiBridge-1000 # Completing the basic FortiBridge configurationConnecting to the FortiBridge CLI using Telnet To connect to the CLI using Telnet To change the management IP address Adding an administrator passwordTo add an administrator password Changing the management IP address To add static routes Changing DNS server IP addressesAdding static routes To change DNS server IP addresses Changing the system time and date Allowing management access to the EXT 1 interfaceAdding administrator accounts To reset to factory defaults from the FortiBridge CLI Resetting to the factory default configurationInstalling FortiBridge unit firmware Upgrading to a new firmware version To upgrade to a new firmware versionExecute restore image namestr tftpip Execute restore image FBG1000-v10-build010-FORTINET.out To revert to a previous firmware version Reverting to a previous firmware version Enter Tftp server address Installing firmware from a system rebootTo install firmware from a system reboot Hit any key to stop autoboot Get system status Enter firmware image file image.out Example network settings Configuration and operating procedures Configuring FortiBridge probes Configuring FortiBridge probes To configure probe settings Probe settings Enabling probes To enable and configure FortiBridge probesConfig probe probelist ping set status enable End Go to System Status Session Config probe probelist Imap set status enable EndVerifying that probes are functioning To verify that probes are functioning Tuning the failure threshold and probe interval Configuring FortiBridge alerts FortiBridge syslog To configure alert emailConfig alertemail setting set server mail.myorg.com End FortiBridge alert email FortiBridge Snmp To configure FortiBridge syslogConfig log syslogd setting set server End To resume normal operation from bypass mode Recovering from a FortiGate failureTo add and enable an Snmp community Config system snmp community edit Set name snmp1 End To back up the FortiBridge configuration Manually switching between FortiBridge operating modesBacking up and restoring the FortiBridge configuration Execute switch-mode Backing up and restoring the FortiBridge configuration Backing up and restoring the FortiBridge configuration CLI basics Connecting to the FortiBridge CLI using SSH or TelnetSetting administrative access for SSH or Telnet To use the CLI to configure SSH or Telnet access Get system interface namestr Other access methodsConnecting to the FortiBridge CLI using SSH Set allowaccess ping telnet ssh To connect to the CLI using SSH Connecting to the FortiBridge CLI using SSH or Telnet Config CLI commands Examples Alertemail settingCommand syntax pattern Related Commands Example Log syslogd setting Show probe probelist Probe probelist ping http ftp pop3 smtp imapGet probe probelist Get probe probelist http Syslog Probe setting Rw w System accprofile Show system accprofile Get system accprofileGet system accprofile policyprofile Password passwordstr System admin Show system admin Get system adminGet system admin newadmin Show system console Config system console set EndSystem console Get system console Show system dns System dnsGet system dns Get system status Failbypass System failclose System failclose Minutesinteger System global Show system global Get system global Show system interface internal System interface internal externalGet system interface internal System manageip Config system manageip Set ip 192.168.2.80 255.255.255.0 end Distanceinteger System route System snmp community Config hosts Show system snmp community Get system snmp community Execute CLI commands Execute backup config fbdg.cfg BackupCommand syntax Execute backup config filenamestr tftp-serveripv4 Execute date 09/17/2004 DateExecute date datestr datestr has the form mm/dd/yyyy, where Execute factoryreset Factoryreset Execute ping addressipv4 host-namestr Ping Execute reboot Reboot Execute restore config backupconfig Restore Switch-mode Execute time timestr Time Time Index 09-30000-0163-20061109 Snmp SSH