Backup, Command syntax | Fortinet Version 3.0 guide

backup

execute CLI commands

backup

Backup the FortiBridge configuration to a file on a TFTP server.

Command syntax

execute backup config <filename_str> <tftp-server_ipv4>

Keywords and variables	Description

config	Back up the FortiBridge configuration.
<filename_str>	The name to give the file that is copied to the TFTP server.
<tftp-server_ipv4>	The TFTP server IP address.

Example

This example shows how to backup a system configuration file from the FortiBridge unit to a TFTP server. The name to give the configuration file on the TFTP server is fbdg.cfg. The IP address of the TFTP server is 192.168.1.23.

execute backup config fbdg.cfg 192.168.1.23

74	FortiBridge Version 3.0 Administration Guide
	09-30000-0163-20061109

Image 74

Fortinet Version 3.0 manual Backup, Command syntax, Execute backup config filenamestr tftp-serveripv4

Contents

M i n i s t r a t i o n G u i d e Trademarks Regulatory compliance Contents Config CLI commands Configuration and operating proceduresUsing the CLI Execute CLI commands IndexPage About FortiBridge About this document Fortinet tools and documentation CD Customer service and technical supportFortinet documentation Fortinet Knowledge Center FortiBridge operating principles Example FortiBridge application Connecting the FortiBridge unit Connecting the FortiBridge-1000 copper gigabit ethernet How the FortiBridge unit monitors the FortiGate unit Normal mode operationConnecting the FortiBridge-1000F fiber gigabit ethernet Normal mode operation Probes and FortiGate firewall policies Probe interval and probe threshold Enabling probes to detect FortiGate hardware failureEnabling probes to detect FortiGate software failure Bypass mode operation FortiBridge power failure Example FortiGate HA cluster FortiBridge application Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces Example configuration with other FortiGate interfaces FortiBridge-1000 Package contents FortiBridge unit basic information FortiBridge-1000F Package contents Mounting instructions Technical specifications LED indicators Connectors Factory default configuration Connecting and turning on the FortiBridge unit Connecting and turning on the FortiBridge-1000 unit To connect and turn on the FortiBridge-1000F unit Connecting and turning on the FortiBridge-1000F unitTo connect and turn on the FortiBridge-1000 unit FortiBridge-1000 login Connecting to the command line interface CLIConnecting to the FortiBridge console To connect to the FortiBridge console for the first time To connect to the CLI using Telnet Completing the basic FortiBridge configurationConnecting to the FortiBridge CLI using Telnet Welcome FortiBridge-1000 # Changing the management IP address Adding an administrator passwordTo add an administrator password To change the management IP address To change DNS server IP addresses Changing DNS server IP addressesAdding static routes To add static routes Changing the system time and date Allowing management access to the EXT 1 interfaceAdding administrator accounts To reset to factory defaults from the FortiBridge CLI Resetting to the factory default configurationInstalling FortiBridge unit firmware Execute restore image FBG1000-v10-build010-FORTINET.out To upgrade to a new firmware versionExecute restore image namestr tftpip Upgrading to a new firmware version Reverting to a previous firmware version To revert to a previous firmware version Hit any key to stop autoboot Installing firmware from a system rebootTo install firmware from a system reboot Enter Tftp server address Enter firmware image file image.out Get system status Configuration and operating procedures Example network settings Configuring FortiBridge probes Configuring FortiBridge probes Probe settings To configure probe settings Enabling probes To enable and configure FortiBridge probesConfig probe probelist ping set status enable End To verify that probes are functioning Config probe probelist Imap set status enable EndVerifying that probes are functioning Go to System Status Session Configuring FortiBridge alerts Tuning the failure threshold and probe interval FortiBridge alert email To configure alert emailConfig alertemail setting set server mail.myorg.com End FortiBridge syslog FortiBridge Snmp To configure FortiBridge syslogConfig log syslogd setting set server End Config system snmp community edit Set name snmp1 End Recovering from a FortiGate failureTo add and enable an Snmp community To resume normal operation from bypass mode Execute switch-mode Manually switching between FortiBridge operating modesBacking up and restoring the FortiBridge configuration To back up the FortiBridge configuration Backing up and restoring the FortiBridge configuration Backing up and restoring the FortiBridge configuration To use the CLI to configure SSH or Telnet access Connecting to the FortiBridge CLI using SSH or TelnetSetting administrative access for SSH or Telnet CLI basics Set allowaccess ping telnet ssh Other access methodsConnecting to the FortiBridge CLI using SSH Get system interface namestr To connect to the CLI using SSH Connecting to the FortiBridge CLI using SSH or Telnet Config CLI commands Examples Alertemail settingCommand syntax pattern Related Commands Log syslogd setting Example Get probe probelist http Probe probelist ping http ftp pop3 smtp imapGet probe probelist Show probe probelist Probe setting Syslog System accprofile Rw w Show system accprofile Get system accprofileGet system accprofile policyprofile System admin Password passwordstr Show system admin Get system adminGet system admin newadmin Get system console Config system console set EndSystem console Show system console Show system dns System dnsGet system dns Get system status System failclose Failbypass System failclose System global Minutesinteger Get system global Show system global Show system interface internal System interface internal externalGet system interface internal Config system manageip Set ip 192.168.2.80 255.255.255.0 end System manageip System route Distanceinteger Config hosts System snmp community Get system snmp community Show system snmp community Execute CLI commands Execute backup config filenamestr tftp-serveripv4 BackupCommand syntax Execute backup config fbdg.cfg Execute date 09/17/2004 DateExecute date datestr datestr has the form mm/dd/yyyy, where Factoryreset Execute factoryreset Ping Execute ping addressipv4 host-namestr Reboot Execute reboot Restore Execute restore config backupconfig Switch-mode Time Execute time timestr Time Index 09-30000-0163-20061109 Snmp SSH