Understanding Tours, Viewing a Preset | Honeywell IV REV B instruction

Fusion IV DVR User Guide

6.Enter a Dwell Time and Speed Setting. This is used for the Tour 2 function (Each preset can have a different Dwell and Speed setting).

7.Click Set once the camera is in the desired position.

8.Enter a name in the new window and click OK.

Note Preset positions can also be created using the advanced buttons on the PTZ graphical controller.

Viewing a Preset

1.From the Live View screen select the PTZ camera by clicking on it.

2.Using the keyboard click the number keys corresponding with the Preset Positions. The camera will move to the saved Preset.

3.Presets can also be activated using the on-screen PTZ controller. Open the controller and click a preset number button.

Understanding Tours

The following section explains PTZ Tour options. Not every Tour method will be available for each PTZ camera.

Preset Tour

Cycles through the selected Recorded

Presets.

Preset Tour 2

Cycles through the selected Recorded

Presets with the addition of a definable

Travel Speed and Dwell Time.

Mimic Tour

‘Mimics’ a user-defined motion path, copying everything the user does (including speed).

Privacy Zone

Auser-defined masked out area so it cannot be viewed.

Sequence

Displays a list of preset sequences.

This list is only displayed on supported protocols.

Travel Speed

Sets the speed at which a PTZ moves from one Preset position to the next (when using Preset Tour 1).

Dwell Time

Defines the length of time (in seconds) that a PTZ Tour stays on a Preset Position (when using Preset Tour 1).

The Honeywell VCL Tour has been updated. Preset 1 now obeys configured speed and dwell times and Preset 2 uses PTZ dome defaults.

________________________________________________________________________________________________________

Document 800-05305V1 Rev B	101
10/11

Image 101

Honeywell IV REV B user manual Understanding Tours, Viewing a Preset

Contents

Fusion IV REV B DVR Revisions Issue Date Fusion IV DVR User Guide FCC Compliance Statement IEC 417, no Eller IEC 417, no National Power Deviation Standards Rack Mount Instructions UL Notice Optical and Acoustical Statements Important Safeguards Document 800-05305V1 Rev B 10/11 Moisture condensation occurs during the following cases U T I O N Contents Connecting Manually Search 100 Backing up Video Data Included Software SetupLAN / Isdn / Pstn Connections Ldap Integration 126 Product Description Introduction Features Front Panel Controls and Leds Controls and Connections Channel Rear Panel Connectors USB 120R IPS 16 Channel IPS 8/16 Channel IPS 32 Channel Card Configurations IPS 32 Channel IPS 16 Channel H-Series Model IPS 8 Channel H-Series Model Identifying Included Components Getting Started Mouse Setup Keyboard Setup Power Setup Monitor Setup Making Connections Connecting a Video Source Connecting Control Outputs Connecting Sensors Looping Output Termination Looping Outputs Optional Components Connecting a PTZ CameraAttaching the 4-Pin Adapter RS-422 Turning Off the Recorder Turning On the Recorder DVR Basics Setting the Time and Date Importing DVR Settings Accessing the DVR UtilityExporting DVR Settings Changing Video Format Live View screen Live Camera Options Special Recording Recording Status IndicatorCamera View Dual Monitor Camera Display Menu Screen Division Buttons Custom Live View Divisions Click Sequence Setting Setup Overview Setup Options Setup Screen Set Up New Camera Camera Setup Connecting Manually Connecting a Network DeviceNetwork Video Click Network Video Click the Add/Remove Device tab Assigning a Network Device to a Channel Connecting with Camera FinderClick Get Device Click Network Video Assigning Audio Channels to a Network Device Enable/Disable Live Video Camera ConfigurationDisplaying More Columns Manufacturer Record FPS Model Frame Rate Regular Interval Recording Motion SetupAccessing the Configuration Menu Select the Enable Sabotage Detection check box Enable Sabotage DetectionClick Motion in Setup Create a Motion Area Beep on Login Fail General Setup Enabling Intensive Recording Voice WarningIntensive Recording Overview Volume Video Loss Alarm Connecting a Second Monitor Connecting to a Wide Screen Display Custom Mode Auto Sequence SettingOpen General setup and click Sequence Setting Create Custom Auto Sequence Frame Select Frame Setup Standard Models Series Models IPS Breakdown for Each Resolution PAL IPS Breakdown for Each Resolution NtscMaximum IPS Table Channel Frame Allocation Schedule Setup Default Schedule Default SchedulesDay of the Week Creating a Simple Schedule By Example Step Click the Single Selection Mode button Step Step Schedule example will be as follows Scheduling Sensors and Relays By Example Click the Single Selection Mode button Step Step Verifying a Recording Schedule Configure Sensor Response Sensor Setup Hybrid Sensor Setup Activate PTZ Preset on Sensor Time Out Value Network Setup Resolution Administration Disk Management Enable Ddns Setting up DdnsClick The Administration tab Set the IP Address User Management Enter a User Name and PasswordAdd a New User Click User Management Default Administrator Password Changing the Administrator PasswordLog Management User Rank Set up Log Management Options Users Status Check / EmailGeneral Smart Information Storage CheckRecording Data Check Select the Enable Smart Alarm check box Alarm EventSelect the Use Email Alarm check box Data Management Information Activate Instant Recording Instant RecordingSearching ‘Instant Recorded’ Video Click Index Search Search Overview Search Play Controls Adjusting the Brightness of an ImageHour / Minute Controls Brightness / Speed / Zoom Zooming in on an Image Adjust the Brightness of an ImageZooming in on a Portion of an Image Open Video from a Saved Location Printing an Image Performing a Basic SearchTime Sync After Image Removal Save to JPG or AVI Daylight Saving Time AVI File Select the Export Type Image File JPG or AVI File Modify Bookmarks Bookmarks Click Use Bookmark Data Single Clip BackupSingle Clip Backup Using Bookmark Data Index Search Results Display Index SearchPerforming an Index Search Preview Search Performing a Preview Search Object Search Click Object Search on the Search screen Performing an Object Search Performing a Status Search Status Search Performing a Motion Search Motion SearchMotion Area check box Continuous Recording check box Audio Playback Pan / Tilt / Zoom Overview Setting up a PTZ CameraPan / Tilt / Zoom Enable the PTZ Settings Creating a Preset Advanced PTZ SetupCreating and Viewing Preset Positions Understanding Tours Viewing a Preset Viewing the Preset Tour Creating a Preset TourCreating a Preset Tour2 Viewing the Preset Tour2 PTZ Tour Scheduling PTZ Status on CloseActivating the PTZ Status on Close Option Create PTZ Tour Schedule Opening and Editing the Honeywell Maxpro Menu PTZ Address SettingAccessing PTZ Menus Controlling a PTZ Camera Using the On-Screen Compass AUX Buttons Using the PTZ Controller Nero Express Backup OverviewBacking up Video Data Backup Status Performing a General BackupGeneral Screen Overview Hour / Minutes Clip Screen Overview Performing a Clip BackupSet the Start Time and End Time under Time Setup Scheduled Screen Overview Performing a Scheduled BackupSpecifying Scheduled Backup Drives LAN Overview LAN / Isdn / Pstn Connections Click Local Area Connections and then click Properties Connecting to a LAN Using TCP/IPConfiguring TCP/IP Settings Ldap Integration Required Items Installing Ldap DVRINSTANT100-000 Group Description Web Viewer Overview Web ViewerHighlights Basics Closing the Web Viewer Configuring the Server for Remote ConnectionConnecting to a DVR Using Web Viewer Proprietary Viewer Overview Included Software Setup Loading Video from DVD-ROM or Hard Drive Installing the Proprietary Viewer Digital Verifier Overview Installing the Digital VerifierUsing the Digital Verifier Configuring the DVR Alarm Monitor OverviewInstalling the Alarm Monitor Configuring the Client PC Filter Event List Alarm Monitor Window View Recorded Video Search Alarm WindowExport Video Export Quality Fusion Remote Software Overview Remote Client Recommended Requirements Installing the Fusion Remote SoftwareRemote Client Minimum Requirements Disable Remote Setting up the Server to Accept Incoming Communications Creating a New Remote Connection Setting up the Fusion Remote Software Fvms System Requirements Fvms OverviewMinimum Recommended1 Connecting to a DVR Health Check Enable Health Check on the Fusion DVR Honeywell Systems Pacific Honeywell Systems Caribbean/Latin AmericaHoneywell Systems Asia Honeywell Systems Middle East/N. Africa