Connecting Sensors, Connecting Control Outputs | Honeywell IV REV B

Making Connections

Connecting Sensors

Each recorder has up to 16 Sensor inputs. These inputs can be used with devices such as infrared devices, motion device, glass breakage alarms, door and window trips, and many more. The Sensors can be set to Normally Open or Normally Closed inside the software.

There are 4 Common Grounds (-) and 16 sensor inputs (+). There is no power supplied to the ports so an external power supply must be used if power is necessary.

COM

Common

Ground

Sensor Inputs

Connecting Control Outputs

Each recorder has up to 16 Control Outputs. These outputs can be used to trigger devices such as Sirens, Phone Dialers, Lights, and any other relay activated device. There is no power supplied to the ports. Use an external power supply if necessary.

COM

Siren, Alarm, Outside Relays

(-)(+)

External Power Supply (DC 12V)

Use 12V, below 300mA. For controlling lights or other devices, use another external relay.

Maximum voltage is 24V AC @ 1 amp Output uses a Form C Relay

________________________________________________________________________________________________________

30

Image 30

Honeywell IV REV B user manual Connecting Sensors, Connecting Control Outputs

Contents

Fusion IV REV B DVR Revisions Issue Date FCC Compliance Statement Fusion IV DVR User Guide National Power Deviation Standards IEC 417, no Eller IEC 417, no Rack Mount Instructions UL Notice Optical and Acoustical Statements Important Safeguards Document 800-05305V1 Rev B 10/11 Moisture condensation occurs during the following cases U T I O N Contents Connecting Manually Search 100 LAN / Isdn / Pstn Connections Included Software SetupBacking up Video Data Ldap Integration 126 Introduction Product Description Features Controls and Connections Front Panel Controls and Leds Rear Panel Connectors Channel USB Card Configurations 120R IPS 16 Channel IPS 8/16 Channel IPS 32 Channel IPS 32 Channel IPS 8 Channel H-Series Model IPS 16 Channel H-Series Model Getting Started Identifying Included Components Keyboard Setup Mouse Setup Monitor Setup Power Setup Connecting a Video Source Making Connections Connecting Sensors Connecting Control Outputs Looping Outputs Looping Output Termination Attaching the 4-Pin Adapter Connecting a PTZ CameraOptional Components RS-422 Turning On the Recorder Turning Off the Recorder Setting the Time and Date DVR Basics Accessing the DVR Utility Exporting DVR SettingsImporting DVR Settings Live View screen Changing Video Format Live Camera Options Recording Status Indicator Camera ViewSpecial Recording Screen Division Buttons Dual Monitor Camera Display Menu Click Sequence Setting Custom Live View Divisions Setup Options Setup Overview Setup Screen Camera Setup Set Up New Camera Network Video Connecting a Network DeviceConnecting Manually Click Network Video Click the Add/Remove Device tab Click Get Device Connecting with Camera FinderAssigning a Network Device to a Channel Click Network Video Assigning Audio Channels to a Network Device Displaying More Columns Camera ConfigurationEnable/Disable Live Video Manufacturer Record FPS Model Frame Rate Motion Setup Accessing the Configuration MenuRegular Interval Recording Click Motion in Setup Enable Sabotage DetectionSelect the Enable Sabotage Detection check box Create a Motion Area General Setup Beep on Login Fail Voice Warning Intensive Recording OverviewEnabling Intensive Recording Video Loss Alarm Volume Connecting to a Wide Screen Display Connecting a Second Monitor Open General setup and click Sequence Setting Auto Sequence SettingCustom Mode Create Custom Auto Sequence Frame Setup Frame Select Standard Models Series Models Maximum IPS Table IPS Breakdown for Each Resolution NtscIPS Breakdown for Each Resolution PAL Channel Frame Allocation Schedule Setup Day of the Week Default SchedulesDefault Schedule Creating a Simple Schedule By Example Click the Single Selection Mode button Step Step Step Scheduling Sensors and Relays By Example Schedule example will be as follows Click the Single Selection Mode button Step Step Verifying a Recording Schedule Sensor Setup Configure Sensor Response Activate PTZ Preset on Sensor Hybrid Sensor Setup Network Setup Time Out Value Administration Resolution Disk Management Click The Administration tab Setting up DdnsEnable Ddns Set the IP Address Add a New User Enter a User Name and PasswordUser Management Click User Management Log Management Changing the Administrator PasswordDefault Administrator Password User Rank Set up Log Management Options Status Check / Email GeneralUsers Storage Check Recording Data CheckSmart Information Select the Use Email Alarm check box Alarm EventSelect the Enable Smart Alarm check box Data Management Information Searching ‘Instant Recorded’ Video Instant RecordingActivate Instant Recording Click Index Search Search Search Overview Hour / Minute Controls Adjusting the Brightness of an ImagePlay Controls Brightness / Speed / Zoom Zooming in on a Portion of an Image Adjust the Brightness of an ImageZooming in on an Image Open Video from a Saved Location Time Sync Performing a Basic SearchPrinting an Image After Image Removal Daylight Saving Time Save to JPG or AVI Select the Export Type Image File JPG or AVI File AVI File Bookmarks Modify Bookmarks Single Clip Backup Single Clip Backup Using Bookmark DataClick Use Bookmark Data Index Search Performing an Index SearchIndex Search Results Display Preview Search Object Search Performing a Preview Search Performing an Object Search Click Object Search on the Search screen Status Search Performing a Status Search Motion Area check box Motion SearchPerforming a Motion Search Continuous Recording check box Audio Playback Setting up a PTZ Camera Pan / Tilt / ZoomPan / Tilt / Zoom Overview Enable the PTZ Settings Advanced PTZ Setup Creating and Viewing Preset PositionsCreating a Preset Viewing a Preset Understanding Tours Creating a Preset Tour2 Creating a Preset TourViewing the Preset Tour Viewing the Preset Tour2 Activating the PTZ Status on Close Option PTZ Status on ClosePTZ Tour Scheduling Create PTZ Tour Schedule PTZ Address Setting Accessing PTZ MenusOpening and Editing the Honeywell Maxpro Menu Using the On-Screen Compass Controlling a PTZ Camera Using the PTZ Controller AUX Buttons Backup Overview Backing up Video DataNero Express General Screen Overview Performing a General BackupBackup Status Hour / Minutes Performing a Clip Backup Set the Start Time and End Time under Time SetupClip Screen Overview Performing a Scheduled Backup Specifying Scheduled Backup DrivesScheduled Screen Overview LAN / Isdn / Pstn Connections LAN Overview Connecting to a LAN Using TCP/IP Configuring TCP/IP SettingsClick Local Area Connections and then click Properties Ldap Integration Installing Ldap Required Items Group Description DVRINSTANT100-000 Highlights Web ViewerWeb Viewer Overview Basics Configuring the Server for Remote Connection Connecting to a DVR Using Web ViewerClosing the Web Viewer Included Software Setup Proprietary Viewer Overview Installing the Proprietary Viewer Loading Video from DVD-ROM or Hard Drive Installing the Digital Verifier Using the Digital VerifierDigital Verifier Overview Alarm Monitor Overview Installing the Alarm MonitorConfiguring the DVR Configuring the Client PC Alarm Monitor Window Filter Event List Export Video Search Alarm WindowView Recorded Video Export Quality Fusion Remote Software Overview Installing the Fusion Remote Software Remote Client Minimum RequirementsRemote Client Recommended Requirements Setting up the Server to Accept Incoming Communications Disable Remote Setting up the Fusion Remote Software Creating a New Remote Connection Minimum Fvms OverviewFvms System Requirements Recommended1 Connecting to a DVR Enable Health Check on the Fusion DVR Health Check Honeywell Systems Asia Honeywell Systems Caribbean/Latin AmericaHoneywell Systems Pacific Honeywell Systems Middle East/N. Africa