Frame Setup, Frame Select | Honeywell IV REV B manual

Fusion IV DVR User Guide

Frame Setup

The Frame Setup menu allows configuration of the IPS, resolution, quality, and sensitivity of camera channels. When configuring the IPS sliders the BLUE slider represents the IPS the DVR will record during intensive recording and have available for transmitting to remotely connected systems. The RED slider represents the IPS that will be recorded by the DVR under normal recording conditions.

The total IPS of all blue sliders may not exceed the recording IPS of the DVR. The IPS of a red slider may not exceed that of the blue slider for the same channel. The dual sliders allow configuration of the DVR to record at a lower IPS while still being able to transmit at a higher IPS to remote connections.

Ex. If a camera channel is set to 25 IPS (blue) and 7 IPS (red), the DVR will record at 7 IPS and users viewing live video remotely can receive up to 25 IPS.

Note The RED IPS record slider cannot exceed the BLUE IPS capture slider.

Note The Software will not allow the maximum available Frames to be exceeded.

Frame Select

Blue Slider: Sets the IPS recorded during intensive recording and available for viewing on a remote client PC.

Red Slider: Sets the IPS recorded by the DVR during normal recording.

Resolution: Affects the total number of frames per second that are available.

Codec: Select the appropriate codec for each camera (MJPEG, MPEG-4, H.264)

Video Quality: Lower quality video has a smaller file size but appears more pixilated.

Sensitivity: Sets the Keyframe refresh rate. Adjusting this setting can have negative effects on video quality.

Note Do not change the default setting unless instructed by a system administrator.

________________________________________________________________________________________________________

Document 800-05305V1 Rev B	55
10/11

Image 55

Honeywell IV REV B user manual Frame Setup, Frame Select

Contents

Fusion IV REV B DVR Revisions Issue Date Fusion IV DVR User Guide FCC Compliance Statement IEC 417, no Eller IEC 417, no National Power Deviation Standards Rack Mount Instructions UL Notice Optical and Acoustical Statements Important Safeguards Document 800-05305V1 Rev B 10/11 Moisture condensation occurs during the following cases U T I O N Contents Connecting Manually Search 100 Ldap Integration Included Software SetupBacking up Video Data LAN / Isdn / Pstn Connections 126 Product Description Introduction Features Front Panel Controls and Leds Controls and Connections Channel Rear Panel Connectors USB 120R IPS 16 Channel IPS 8/16 Channel IPS 32 Channel Card Configurations IPS 32 Channel IPS 16 Channel H-Series Model IPS 8 Channel H-Series Model Identifying Included Components Getting Started Mouse Setup Keyboard Setup Power Setup Monitor Setup Making Connections Connecting a Video Source Connecting Control Outputs Connecting Sensors Looping Output Termination Looping Outputs RS-422 Connecting a PTZ CameraOptional Components Attaching the 4-Pin Adapter Turning Off the Recorder Turning On the Recorder DVR Basics Setting the Time and Date Exporting DVR Settings Accessing the DVR UtilityImporting DVR Settings Changing Video Format Live View screen Live Camera Options Camera View Recording Status IndicatorSpecial Recording Dual Monitor Camera Display Menu Screen Division Buttons Custom Live View Divisions Click Sequence Setting Setup Overview Setup Options Setup Screen Set Up New Camera Camera Setup Click Network Video Click the Add/Remove Device tab Connecting a Network DeviceConnecting Manually Network Video Click Network Video Connecting with Camera FinderAssigning a Network Device to a Channel Click Get Device Assigning Audio Channels to a Network Device Manufacturer Record FPS Model Frame Rate Camera ConfigurationEnable/Disable Live Video Displaying More Columns Accessing the Configuration Menu Motion SetupRegular Interval Recording Create a Motion Area Enable Sabotage DetectionSelect the Enable Sabotage Detection check box Click Motion in Setup Beep on Login Fail General Setup Intensive Recording Overview Voice WarningEnabling Intensive Recording Volume Video Loss Alarm Connecting a Second Monitor Connecting to a Wide Screen Display Create Custom Auto Sequence Auto Sequence SettingCustom Mode Open General setup and click Sequence Setting Frame Select Frame Setup Standard Models Series Models Channel Frame Allocation IPS Breakdown for Each Resolution NtscIPS Breakdown for Each Resolution PAL Maximum IPS Table Schedule Setup Creating a Simple Schedule By Example Default SchedulesDefault Schedule Day of the Week Step Click the Single Selection Mode button Step Step Schedule example will be as follows Scheduling Sensors and Relays By Example Click the Single Selection Mode button Step Step Verifying a Recording Schedule Configure Sensor Response Sensor Setup Hybrid Sensor Setup Activate PTZ Preset on Sensor Time Out Value Network Setup Resolution Administration Disk Management Set the IP Address Setting up DdnsEnable Ddns Click The Administration tab Click User Management Enter a User Name and PasswordUser Management Add a New User User Rank Changing the Administrator PasswordDefault Administrator Password Log Management Set up Log Management Options General Status Check / EmailUsers Recording Data Check Storage CheckSmart Information Data Management Alarm EventSelect the Enable Smart Alarm check box Select the Use Email Alarm check box Information Click Index Search Instant RecordingActivate Instant Recording Searching ‘Instant Recorded’ Video Search Overview Search Brightness / Speed / Zoom Adjusting the Brightness of an ImagePlay Controls Hour / Minute Controls Open Video from a Saved Location Adjust the Brightness of an ImageZooming in on an Image Zooming in on a Portion of an Image After Image Removal Performing a Basic SearchPrinting an Image Time Sync Save to JPG or AVI Daylight Saving Time AVI File Select the Export Type Image File JPG or AVI File Modify Bookmarks Bookmarks Single Clip Backup Using Bookmark Data Single Clip BackupClick Use Bookmark Data Performing an Index Search Index SearchIndex Search Results Display Preview Search Performing a Preview Search Object Search Click Object Search on the Search screen Performing an Object Search Performing a Status Search Status Search Continuous Recording check box Motion SearchPerforming a Motion Search Motion Area check box Audio Playback Pan / Tilt / Zoom Setting up a PTZ CameraPan / Tilt / Zoom Overview Enable the PTZ Settings Creating and Viewing Preset Positions Advanced PTZ SetupCreating a Preset Understanding Tours Viewing a Preset Viewing the Preset Tour2 Creating a Preset TourViewing the Preset Tour Creating a Preset Tour2 Create PTZ Tour Schedule PTZ Status on ClosePTZ Tour Scheduling Activating the PTZ Status on Close Option Accessing PTZ Menus PTZ Address SettingOpening and Editing the Honeywell Maxpro Menu Controlling a PTZ Camera Using the On-Screen Compass AUX Buttons Using the PTZ Controller Backing up Video Data Backup OverviewNero Express Hour / Minutes Performing a General BackupBackup Status General Screen Overview Set the Start Time and End Time under Time Setup Performing a Clip BackupClip Screen Overview Specifying Scheduled Backup Drives Performing a Scheduled BackupScheduled Screen Overview LAN Overview LAN / Isdn / Pstn Connections Configuring TCP/IP Settings Connecting to a LAN Using TCP/IPClick Local Area Connections and then click Properties Ldap Integration Required Items Installing Ldap DVRINSTANT100-000 Group Description Basics Web ViewerWeb Viewer Overview Highlights Connecting to a DVR Using Web Viewer Configuring the Server for Remote ConnectionClosing the Web Viewer Proprietary Viewer Overview Included Software Setup Loading Video from DVD-ROM or Hard Drive Installing the Proprietary Viewer Using the Digital Verifier Installing the Digital VerifierDigital Verifier Overview Installing the Alarm Monitor Alarm Monitor OverviewConfiguring the DVR Configuring the Client PC Filter Event List Alarm Monitor Window Export Quality Search Alarm WindowView Recorded Video Export Video Fusion Remote Software Overview Remote Client Minimum Requirements Installing the Fusion Remote SoftwareRemote Client Recommended Requirements Disable Remote Setting up the Server to Accept Incoming Communications Creating a New Remote Connection Setting up the Fusion Remote Software Recommended1 Fvms OverviewFvms System Requirements Minimum Connecting to a DVR Health Check Enable Health Check on the Fusion DVR Honeywell Systems Middle East/N. Africa Honeywell Systems Caribbean/Latin AmericaHoneywell Systems Pacific Honeywell Systems Asia