Connecting to a LAN Using TCP/IP | Honeywell IV REV B specification

LAN / ISDN / PSTN Connections

Connecting to a LAN Using TCP/IP

The networking options of the recorder can create and edit all Network settings available on Windows Embedded 7. The recorder comes equipped with a 10/100/1000 Network Interface Card (NIC). This card uses a standard RJ-45 Ethernet connector.

Configuring TCP/IP Settings

1.On the Live View screen, click Exit and select Restart in Windows Mode.

2.Right-click the Network icon located on the desktop and select Properties.

3.Click Local Area Connections and then click Properties.

4.Select the Internet Protocol (TCP/IP) by clicking on it once. Once it is highlighted, click Properties.

5.Select Use the Following IP Address option. Enter the IP Address and Subnet mask appropriate for the network. It is recommended to contact the Network Administrator for appropriate IP settings.

Example: a. Common IP addresses are 10.0.0.25

b. Common Subnet masks are 255.255.255.0

Note In order to connect to the recorder through a remote LAN connection, a static

IP address must be assigned. If the network assigns the IP address automatically (DHCP), contact the Network Administrator for help assigning a static IP address.

6.If the network requires you to specify the DNS information, enter it now by selecting the appropriate DNS options.

7.When finished configuring the TCP/IP settings click OK to close the Internet Protocol (TCP/IP) Properties window.

8.Click OK to close the Local Area Connection Properties window.

9.It may be required to restart Windows for the changes to take effect. Restart windows by clicking the Start button on the desktop and clicking Restart.

________________________________________________________________________________________________________

112

Image 112

Honeywell IV REV B user manual Connecting to a LAN Using TCP/IP, Configuring TCP/IP Settings

Contents

Fusion IV REV B DVR Revisions Issue Date FCC Compliance Statement Fusion IV DVR User Guide National Power Deviation Standards IEC 417, no Eller IEC 417, no Rack Mount Instructions UL Notice Optical and Acoustical Statements Important Safeguards Document 800-05305V1 Rev B 10/11 Moisture condensation occurs during the following cases U T I O N Contents Connecting Manually Search 100 Included Software Setup Backing up Video DataLAN / Isdn / Pstn Connections Ldap Integration 126 Introduction Product Description Features Controls and Connections Front Panel Controls and Leds Rear Panel Connectors Channel USB Card Configurations 120R IPS 16 Channel IPS 8/16 Channel IPS 32 Channel IPS 32 Channel IPS 8 Channel H-Series Model IPS 16 Channel H-Series Model Getting Started Identifying Included Components Keyboard Setup Mouse Setup Monitor Setup Power Setup Connecting a Video Source Making Connections Connecting Sensors Connecting Control Outputs Looping Outputs Looping Output Termination Connecting a PTZ Camera Optional ComponentsAttaching the 4-Pin Adapter RS-422 Turning On the Recorder Turning Off the Recorder Setting the Time and Date DVR Basics Exporting DVR Settings Accessing the DVR UtilityImporting DVR Settings Live View screen Changing Video Format Live Camera Options Camera View Recording Status IndicatorSpecial Recording Screen Division Buttons Dual Monitor Camera Display Menu Click Sequence Setting Custom Live View Divisions Setup Options Setup Overview Setup Screen Camera Setup Set Up New Camera Connecting a Network Device Connecting ManuallyNetwork Video Click Network Video Click the Add/Remove Device tab Connecting with Camera Finder Assigning a Network Device to a ChannelClick Get Device Click Network Video Assigning Audio Channels to a Network Device Camera Configuration Enable/Disable Live VideoDisplaying More Columns Manufacturer Record FPS Model Frame Rate Accessing the Configuration Menu Motion SetupRegular Interval Recording Enable Sabotage Detection Select the Enable Sabotage Detection check boxClick Motion in Setup Create a Motion Area General Setup Beep on Login Fail Intensive Recording Overview Voice WarningEnabling Intensive Recording Video Loss Alarm Volume Connecting to a Wide Screen Display Connecting a Second Monitor Auto Sequence Setting Custom ModeOpen General setup and click Sequence Setting Create Custom Auto Sequence Frame Setup Frame Select Standard Models Series Models IPS Breakdown for Each Resolution Ntsc IPS Breakdown for Each Resolution PALMaximum IPS Table Channel Frame Allocation Schedule Setup Default Schedules Default ScheduleDay of the Week Creating a Simple Schedule By Example Click the Single Selection Mode button Step Step Step Scheduling Sensors and Relays By Example Schedule example will be as follows Click the Single Selection Mode button Step Step Verifying a Recording Schedule Sensor Setup Configure Sensor Response Activate PTZ Preset on Sensor Hybrid Sensor Setup Network Setup Time Out Value Administration Resolution Disk Management Setting up Ddns Enable DdnsClick The Administration tab Set the IP Address Enter a User Name and Password User ManagementAdd a New User Click User Management Changing the Administrator Password Default Administrator PasswordLog Management User Rank Set up Log Management Options General Status Check / EmailUsers Recording Data Check Storage CheckSmart Information Alarm Event Select the Enable Smart Alarm check boxSelect the Use Email Alarm check box Data Management Information Instant Recording Activate Instant RecordingSearching ‘Instant Recorded’ Video Click Index Search Search Search Overview Adjusting the Brightness of an Image Play ControlsHour / Minute Controls Brightness / Speed / Zoom Adjust the Brightness of an Image Zooming in on an ImageZooming in on a Portion of an Image Open Video from a Saved Location Performing a Basic Search Printing an ImageTime Sync After Image Removal Daylight Saving Time Save to JPG or AVI Select the Export Type Image File JPG or AVI File AVI File Bookmarks Modify Bookmarks Single Clip Backup Using Bookmark Data Single Clip BackupClick Use Bookmark Data Performing an Index Search Index SearchIndex Search Results Display Preview Search Object Search Performing a Preview Search Performing an Object Search Click Object Search on the Search screen Status Search Performing a Status Search Motion Search Performing a Motion SearchMotion Area check box Continuous Recording check box Audio Playback Pan / Tilt / Zoom Setting up a PTZ CameraPan / Tilt / Zoom Overview Enable the PTZ Settings Creating and Viewing Preset Positions Advanced PTZ SetupCreating a Preset Viewing a Preset Understanding Tours Creating a Preset Tour Viewing the Preset TourCreating a Preset Tour2 Viewing the Preset Tour2 PTZ Status on Close PTZ Tour SchedulingActivating the PTZ Status on Close Option Create PTZ Tour Schedule Accessing PTZ Menus PTZ Address SettingOpening and Editing the Honeywell Maxpro Menu Using the On-Screen Compass Controlling a PTZ Camera Using the PTZ Controller AUX Buttons Backing up Video Data Backup OverviewNero Express Performing a General Backup Backup StatusGeneral Screen Overview Hour / Minutes Set the Start Time and End Time under Time Setup Performing a Clip BackupClip Screen Overview Specifying Scheduled Backup Drives Performing a Scheduled BackupScheduled Screen Overview LAN / Isdn / Pstn Connections LAN Overview Configuring TCP/IP Settings Connecting to a LAN Using TCP/IPClick Local Area Connections and then click Properties Ldap Integration Installing Ldap Required Items Group Description DVRINSTANT100-000 Web Viewer Web Viewer OverviewHighlights Basics Connecting to a DVR Using Web Viewer Configuring the Server for Remote ConnectionClosing the Web Viewer Included Software Setup Proprietary Viewer Overview Installing the Proprietary Viewer Loading Video from DVD-ROM or Hard Drive Using the Digital Verifier Installing the Digital VerifierDigital Verifier Overview Installing the Alarm Monitor Alarm Monitor OverviewConfiguring the DVR Configuring the Client PC Alarm Monitor Window Filter Event List Search Alarm Window View Recorded VideoExport Video Export Quality Fusion Remote Software Overview Remote Client Minimum Requirements Installing the Fusion Remote SoftwareRemote Client Recommended Requirements Setting up the Server to Accept Incoming Communications Disable Remote Setting up the Fusion Remote Software Creating a New Remote Connection Fvms Overview Fvms System RequirementsMinimum Recommended1 Connecting to a DVR Enable Health Check on the Fusion DVR Health Check Honeywell Systems Caribbean/Latin America Honeywell Systems PacificHoneywell Systems Asia Honeywell Systems Middle East/N. Africa