Alarm Monitor Overview, Configuring the DVR | Honeywell IV REV B

Fusion IV DVR User Guide

Alarm Monitor Overview

The Alarm Monitor software is a utility that streams video across a Local Area Network to a Client PC when an alarm is detected on the DVR. The video that streams across can be stopped, played forwards and backwards, in slow motion or real time.

The utility is loaded at startup and placed in the taskbar. It constantly monitors for a signal from the DVR. When an alarm signal is detected the Alarm Monitor Image Viewer Window opens and starts playing the video from the camera associated to the alarm.

Installing the Alarm Monitor

1.Insert the Software Installation Disc into the CDROM. (Do not install on the DVR) Select the Alarm Monitor option to begin installation and accept the license agreement.

2.Follow the on screen instructions.

3.Click the Finish button to complete the installation.

Configuring the DVR

To enable the Alarm Monitor on the DVR follow these steps:

1.Enter Setup and click the Recording Schedule tab.

2.Assign the desired sensors to the desired cameras. Refer to the Recording Schedule section of this manual for in depth instructions on how to do this.

3.Enable Sensor Event and/or Motion Event in the Alarm Options Section of each schedule number to send alarm events to the Alarm Monitor.

Note The Remote Alarm and Emergency Alarm options are used by the more

advanced FVMS multi site management and control software.

4.Enter the IP Address of the computer running the Alarm Monitor software.

5.Click the Network tab and make sure that Disable Remote Control is not checked.

6.The Alarm Monitor uses the Emergency Port to transfer the data through. The port can be adjusted inside the Network Menu if necessary. It is recommended that the default port setting be used.

7.Click the Sensor Menu tab.

8.Configure the Sensors assigned to cameras.

9.Click OK.

________________________________________________________________________________________________________

Document 800-05305V1 Rev B	121
10/11

Image 121

Honeywell IV REV B user manual Alarm Monitor Overview, Installing the Alarm Monitor, Configuring the DVR

Contents

Fusion IV REV B DVR Revisions Issue Date Fusion IV DVR User Guide FCC Compliance Statement IEC 417, no Eller IEC 417, no National Power Deviation Standards Rack Mount Instructions UL Notice Optical and Acoustical Statements Important Safeguards Document 800-05305V1 Rev B 10/11 Moisture condensation occurs during the following cases U T I O N Contents Connecting Manually Search 100 Backing up Video Data Included Software SetupLAN / Isdn / Pstn Connections Ldap Integration 126 Product Description Introduction Features Front Panel Controls and Leds Controls and Connections Channel Rear Panel Connectors USB 120R IPS 16 Channel IPS 8/16 Channel IPS 32 Channel Card Configurations IPS 32 Channel IPS 16 Channel H-Series Model IPS 8 Channel H-Series Model Identifying Included Components Getting Started Mouse Setup Keyboard Setup Power Setup Monitor Setup Making Connections Connecting a Video Source Connecting Control Outputs Connecting Sensors Looping Output Termination Looping Outputs Optional Components Connecting a PTZ CameraAttaching the 4-Pin Adapter RS-422 Turning Off the Recorder Turning On the Recorder DVR Basics Setting the Time and Date Exporting DVR Settings Accessing the DVR UtilityImporting DVR Settings Changing Video Format Live View screen Live Camera Options Camera View Recording Status IndicatorSpecial Recording Dual Monitor Camera Display Menu Screen Division Buttons Custom Live View Divisions Click Sequence Setting Setup Overview Setup Options Setup Screen Set Up New Camera Camera Setup Connecting Manually Connecting a Network DeviceNetwork Video Click Network Video Click the Add/Remove Device tab Assigning a Network Device to a Channel Connecting with Camera FinderClick Get Device Click Network Video Assigning Audio Channels to a Network Device Enable/Disable Live Video Camera ConfigurationDisplaying More Columns Manufacturer Record FPS Model Frame Rate Accessing the Configuration Menu Motion SetupRegular Interval Recording Select the Enable Sabotage Detection check box Enable Sabotage DetectionClick Motion in Setup Create a Motion Area Beep on Login Fail General Setup Intensive Recording Overview Voice WarningEnabling Intensive Recording Volume Video Loss Alarm Connecting a Second Monitor Connecting to a Wide Screen Display Custom Mode Auto Sequence SettingOpen General setup and click Sequence Setting Create Custom Auto Sequence Frame Select Frame Setup Standard Models Series Models IPS Breakdown for Each Resolution PAL IPS Breakdown for Each Resolution NtscMaximum IPS Table Channel Frame Allocation Schedule Setup Default Schedule Default SchedulesDay of the Week Creating a Simple Schedule By Example Step Click the Single Selection Mode button Step Step Schedule example will be as follows Scheduling Sensors and Relays By Example Click the Single Selection Mode button Step Step Verifying a Recording Schedule Configure Sensor Response Sensor Setup Hybrid Sensor Setup Activate PTZ Preset on Sensor Time Out Value Network Setup Resolution Administration Disk Management Enable Ddns Setting up DdnsClick The Administration tab Set the IP Address User Management Enter a User Name and PasswordAdd a New User Click User Management Default Administrator Password Changing the Administrator PasswordLog Management User Rank Set up Log Management Options General Status Check / EmailUsers Recording Data Check Storage CheckSmart Information Select the Enable Smart Alarm check box Alarm EventSelect the Use Email Alarm check box Data Management Information Activate Instant Recording Instant RecordingSearching ‘Instant Recorded’ Video Click Index Search Search Overview Search Play Controls Adjusting the Brightness of an ImageHour / Minute Controls Brightness / Speed / Zoom Zooming in on an Image Adjust the Brightness of an ImageZooming in on a Portion of an Image Open Video from a Saved Location Printing an Image Performing a Basic SearchTime Sync After Image Removal Save to JPG or AVI Daylight Saving Time AVI File Select the Export Type Image File JPG or AVI File Modify Bookmarks Bookmarks Single Clip Backup Using Bookmark Data Single Clip BackupClick Use Bookmark Data Performing an Index Search Index SearchIndex Search Results Display Preview Search Performing a Preview Search Object Search Click Object Search on the Search screen Performing an Object Search Performing a Status Search Status Search Performing a Motion Search Motion SearchMotion Area check box Continuous Recording check box Audio Playback Pan / Tilt / Zoom Setting up a PTZ CameraPan / Tilt / Zoom Overview Enable the PTZ Settings Creating and Viewing Preset Positions Advanced PTZ SetupCreating a Preset Understanding Tours Viewing a Preset Viewing the Preset Tour Creating a Preset TourCreating a Preset Tour2 Viewing the Preset Tour2 PTZ Tour Scheduling PTZ Status on CloseActivating the PTZ Status on Close Option Create PTZ Tour Schedule Accessing PTZ Menus PTZ Address SettingOpening and Editing the Honeywell Maxpro Menu Controlling a PTZ Camera Using the On-Screen Compass AUX Buttons Using the PTZ Controller Backing up Video Data Backup OverviewNero Express Backup Status Performing a General BackupGeneral Screen Overview Hour / Minutes Set the Start Time and End Time under Time Setup Performing a Clip BackupClip Screen Overview Specifying Scheduled Backup Drives Performing a Scheduled BackupScheduled Screen Overview LAN Overview LAN / Isdn / Pstn Connections Configuring TCP/IP Settings Connecting to a LAN Using TCP/IPClick Local Area Connections and then click Properties Ldap Integration Required Items Installing Ldap DVRINSTANT100-000 Group Description Web Viewer Overview Web ViewerHighlights Basics Connecting to a DVR Using Web Viewer Configuring the Server for Remote ConnectionClosing the Web Viewer Proprietary Viewer Overview Included Software Setup Loading Video from DVD-ROM or Hard Drive Installing the Proprietary Viewer Using the Digital Verifier Installing the Digital VerifierDigital Verifier Overview Installing the Alarm Monitor Alarm Monitor OverviewConfiguring the DVR Configuring the Client PC Filter Event List Alarm Monitor Window View Recorded Video Search Alarm WindowExport Video Export Quality Fusion Remote Software Overview Remote Client Minimum Requirements Installing the Fusion Remote SoftwareRemote Client Recommended Requirements Disable Remote Setting up the Server to Accept Incoming Communications Creating a New Remote Connection Setting up the Fusion Remote Software Fvms System Requirements Fvms OverviewMinimum Recommended1 Connecting to a DVR Health Check Enable Health Check on the Fusion DVR Honeywell Systems Pacific Honeywell Systems Caribbean/Latin AmericaHoneywell Systems Asia Honeywell Systems Middle East/N. Africa