Manuals / HP / Computer Equipment / Computer Accessories

HP 16500C, 16501A LOGIC manual An Oscilloscope Display Saved as a TIF Image

Models: 16500C 16501A LOGIC

1 130

Download 130 pages 6.88 Kb

<>

Specs Intermittent data errors Symbols Warranty No Configuration File Loaded Preprocessor Problems To set up the HP 16500C Skew Adjustment Target system will not boot up Using the LAN Interface

Page 73

File Management

To save a menu or measurement as a graphic image

An Oscilloscope Display Saved as a TIF Image

3–11

Page 72 Page 74

Image 73

HP 16500C, 16501A LOGIC manual An Oscilloscope Display Saved as a TIF Image

Page 72 Page 74

Related pages Troubleshooting for Samsung MG28J5255UW/EO SPECIFICATIONS/COMPONENT Identification for American Dryer Corp ML-55HS Hot Surface Indicator Light under ceramic glass for Whirlpool RF340BXK Electrode and Amperage Selection Chart for Miller Electric 145 DXR, 145 Reviewing and Searching when Recording for Canon MV 950 Installing Cisco VT Advantage for Cisco Systems Digital Camera Spare Parts List for for Furuno FM-8800D/8800S Language Code List for JVC DR-MV5SEK UK Accessories for Plantronics 640E Cable Replacement Note for Apple 3400C/200 Is there a recipe book available for KMC5XX and KMM7XX Kenwood models?

Contents

HP 16500C /16501A Logic Analysis System Install measurement modules in any slot Powerful, easy-to-use interfaceCalibrate measurement modules after installation System of measurement modules Iii Page This Book HP 16500C /16501A Logic Analysis System User’s Reference See Also Contents Contents Skew AdjustmentSpecial displays Inverse Assembler Problems Preprocessor ProblemsIntermodule Measurement Problems Messages Triggering Triggering Select the state analyzer Trigger menu Set Count to Time To store and time the execution of a subroutineTo store and time the execution of a subroutine As shown in the display To store and time the execution of a subroutine Example Select the state analyzer Trigger menu To trigger on the nth iteration of a loopTo trigger on the nth iteration of a loop To trigger on the nth recursive call of a recursive function Triggering on the 22nd Call of a Recursive Function To trigger on entry to a function To trigger on entry to a function Triggering on Entry to a Function Capturing a Bad Write to a Variable To trigger on a loop that occasionally runs too long To trigger on a loop that occasionally runs too long Verifying Correct Return from a Function Call To trigger after all status bus lines finish transitioning To trigger after all status bus lines finish transitioning To find the nth assertion of a chip select line To find the nth assertion of a chip select line Verifying Setup Time for Memory Address Select the timing analyzer Trigger menu Triggering When I/O Data Not Returned To test minimum and maximum pulse limits To test minimum and maximum pulse limits Triggering when a Pulse Exceeds Minimum or Maximum Limits To detect a handshake violation To detect a handshake violation To detect bus contention To detect bus contention Made by the two analyzers Cross-Arming Trigger ExamplesIntermodule Measurements To examine software execution when a timing violation occurs Trigger on arm ∙ Edge1 1 time Intermodule Measurements Intermodule Measurements Intermodule Measurements Intermodule Measurement Examples To set up a group run of modules within the HP 16500CSelect the Group Run field in the upper right hand corner To set up a group run of modules within the HP 16500C Start the external instrument or system State Analyzer and Oscilloscope armed from Port Select Port IN/OUT Select Done in the Port IN/OUT Setup menuSelect the Port OUT Source field Driving the Port Out BNC in an Intermodule Measurement Intermodule Measurements Module Status Intermodule Measurements Module Time Correlation To use a timing analyzer to detect a glitch To use a timing analyzer to detect a glitch To capture the waveform of a glitch To capture the waveform of a glitch Intermodule Measurements To test a circuit using stimulus-response To test a circuit using stimulus-responseSelect the Intermodule menu Intermodule Measurements Intermodule Measurements Special Displays in this chapter Interleaved Trace Lists Special displays To interleave trace lists To interleave trace lists Interleaved Trace Lists on the HP 16550A Select the module for which you wish to show waveforms Skew Adjustment in this chapter Skew Adjustment Set up the trigger conditions for each module Connect an input signal from each module to the same signalSelect Group Run Record the differences shown by the two modules File Management File Management Transferring Files Using the Flexible Disk Drive To save a measurement configuration To save a measurement configuration Saving the Oscilloscope Configuration for Skew Testing To load a measurement configuration To load a measurement configuration To load a measurement configuration To save a trace list in Ascii format To save a trace list in Ascii format Part of a Trace Listing Saved as an Ascii File To save a menu or measurement as a graphic image To save a menu or measurement as a graphic image An Oscilloscope Display Saved as a TIF Image To load system software To load system software Using the LAN Interface To set up the HP 16500C To set up the HP 16500C HP 16500C System Programmer’s Guide for more information on To set up the HP 16500C Example Run the analyzer to acquire data Set up the system for the measurement you want to make \ copy L\slotc\data.asc\68000bus\addrlo local path name \system\graphics Concepts Concepts Trigger Sequencer Trigger Sequence Specification Sequence-Advance Specification Trigger specification can look like the following For example Analyzer Resources Limitations Affecting Use of Analyzer Resources Group Pair Resource Operation Pair Links HP 16550A Resource Division Timing Analyzer Inverse Assembler Inverse Assembly Synchronization Settings Preprocessor User’s Guide for more information on switchSymbols Configuration Translation for Analyzer Modules Concepts Concepts Page If You Have a Problem If You Have a Problem Intermittent data errors Analyzer ProblemsUnwanted triggers No activity on activity indicators No Setup/Hold field on format screenNo Setup/Hold field on format screen Capacitive loading No trace list display No trace list display Target system will not boot up Preprocessor Problems Erratic trace measurements Slow clockSlow clock Erratic trace measurements No inverse assembly or incorrect inverse assembly Inverse Assembler Problems Inverse assembler will not load or run Inverse assembler will not load or run An event wasn’t captured by one of the modules Intermodule Measurement Problems Messages Default Calibration Factors Loaded HP 16540, 16541,Inverse Assembler Not Found Measurement Initialization Error Measurement Initialization Error No Configuration File Loaded No Configuration File LoadedSelected File is Incompatible Slow or Missing Clock State Clock Violates Overdrive Specification State Clock Violates Overdrive SpecificationTime from Arm Greater Than 41.93 ms Waiting for Trigger Waiting for Trigger Application Notes Application Notes and Product Notes Application Notes Application Notes Page Attenuation factor Glossary Input impedance Glossary-3 Div See horizontal sweep speed State sequence levels The indi Glossary-6 Glossary-7 Glossary-8 Data Index Index-2 Index-3 Index-4 Document Warranty Product Warranty

Top Page Image Contents