HP 200 Unified Threat Management (UTM) Appliance specs

Up to five users can concurrently log in to the device through the Web interface.

Figure 46 Web login page

Adding a Web login account

Perform the following configuration at the CLI:

1.Add a Web user. Set the username to userA, password to 123456, and user privilege level to 3.

[HP] local-user userA New local user added.

[HP-luser-userA] service-type web

[HP-luser-userA] password simple 123456

[HP-luser-userA] authorization-attribute level 3

[HP-luser-userA] quit

2.Add an interface to the management zone.

To allow users to log in to the device's Web interface through an interface other than the management interface GigabitEthernet 0/0, you must add the interface to the management zone.

[HP] zone name management

[HP-zone-management] import interface gigabitethernet0/1

Configuring Web login

To enable Web login, log in through the console port, and perform the following configuration tasks:

•Enable HTTP or HTTPS service.

•Configure the IP address of a Layer 3 interface, and make sure the interface and the configuration terminal can reach each other.

•Configure a local user account for Web login.

The device supports HTTP 1.0 and HTTPS for transferring webpage data across the Internet.

HTTPS uses SSL to encrypt data between the client and the server for data integrity and security, and is more secure than HTTP. You can define a certificate attribute-based access control policy to allow only legal clients to access the device.

HTTP login and HTTPS login are separate login methods. To use HTTPS login, you do not need to configure HTTP login.

Table 10 shows the basic Web login configuration requirements.

52

Image 58

HP 200 Unified Threat Management (UTM) Appliance manual Adding a Web login account, Configuring Web login

Contents

HP Firewalls and UTM Devices Page Contents Page Iii Page Overview OverviewF1000-A-EI/F1000-S-EI Appearance F1000-E Front view F5000 Aspf Firewall modules Firewall module for 5800 switches Enhanced firewall modules UTM products U200-A U200-A front view U200-S Application scenariosF1000-A-EI/F1000-S-EI Firewall application Virtual firewall application VPN application F1000-E F5000 Firewall modules Enhanced firewall modules Clound computing data center application Remote access application Enterprise network applicatoin UTM Network diagram Login methods Login overviewLogin methods at a glance Login method Default setting and configuration requirements CLI user interfaces CLI login method and user interface matrixUser interface Login method User interface assignmentPage Logging in to the CLI Default console port propertiesParameter Default Logging in through the console port for the first time Connection description Configuring console login control settings Setting the properties of the serial port Command Remarks Configuring none authentication for console loginAuthentication Configuration tasks Reference Mode Last-number Configuring password authentication for console login Configuring scheme authentication for console login Domain domain-name Configuration GuidePassword Hwtacacs-scheme-name Configuring common console user interface settings optional Speed speed-value Telnet login Logging in through Telnet Telnet server and Telnet client configuration requirements Device role Requirements Configuring none authentication for Telnet login Configuring password authentication for Telnet login Telnetting to the device without authentication Configuring scheme authentication for Telnet login Password authentication interface for Telnet login User only depend on the user Configuring common VTY user interface settings optional Step Command Remarks Character Using the device to log in to a Telnet serverCommand Value Logging in through SSH To use the device to log in to a Telnet server Configuring the SSH server on the device SSH server and client requirements Ldap-scheme-name Started Command Reference Local login through the AUX portUsing the device to log in to an SSH server Ssh2 server Hardware Feature compatible AUX login diagram Configuring none authentication for AUX login Configuring password authentication for AUX login Configuring scheme authentication for AUX login Password authentication interface for AUX login Apply the specified AAA Configuring common settings for AUX login optional Ip alias ip-address port-number Display type of both the device Login procedure Default AUX port properties Connecting the AUX port to a terminal Power on the device and press Enter at the prompt Include regular-expression Displaying and maintaining CLI loginTask Command Remarks Regular-expression Send all num1 aux console Available in user view Vty num2 Logging in by using the default Web login settings Configuration guidelinesLogging in to the Web interface Adding a Web login account Configuring Web login Object Requirements Configuring Http loginBasic Web login configuration requirements Web captcha verification-code Interface interface-type Interface-number Configuring Https loginVerification-code VPN Configuration Guide Policy-name Https Mask mask-length Configuration procedure Displaying and maintaining Web loginHttp login configuration example Network requirements Https login configuration example Configure the host Https client # Associate the Https service with SSL server policy myssl# Enable the Https service # Create RSA local key pairs Symptom Troubleshooting Web browserFailure to access the device through the Web interface Configuring the Internet Explorer settings Internet Explorer setting Configuring Firefox Web browser settings Click OK in the Security Settings dialog box Firefox Web browser setting Configuring SNMPv3 access Accessing the device through SnmpConfiguring Snmp access Prerequisites Priv-password acl acl-number acl ipv6 ipv6-acl-number Configuring SNMPv1 or SNMPv2c accessIpv6 ipv6-acl-number See Getting Started Command Reference Notify-view acl acl-number acl # Enable the Snmp agent Snmp login exampleStepCommand Remarks # Configure an Snmp groupPage Logging in to the firewall module from the network device Feature and hardware compatibilityLogging in to the firewall module from the network device Resetting the system of the firewall module Configuring the Acsei protocol Acsei starts up and runs in the following procedures Acsei timersConfiguring Acsei server on the network device Acsei startup and running Network requirements Configuring Acsei client on the firewall moduleDisplaying and maintaining Acsei server and client Client-id # Set the monitoring timer to 10 seconds Configuration procedure# Set the clock synchronization timer to 10 minutes # Log in to the firewall modulePage Performing basic configuration in the Web interface Basic configurationOverview Basic configuration wizard-1/6 Click Next For basic configuration appears Basic configuration wizard-2/6 basic information Click Next For configuring service management appears Basic configuration wizard-3/6 service management Another service Assign IP addresses to the interfaces Click Next For configuring NAT appears Configuration itemsConfigure the parameters as described in Table IP/Wildcard Performing basic configuration at the CLI Basic configuration wizard-6/6 Ip address ip-address mask-length mask Global-nameInterface interface-type Zone name zone-name id zone-id Configuration Managing the device Configuring the device name in the Web interfaceConfiguring the device name at the CLI Hardware Supported storage medium Configuring the system time Configuring the system time in the Web interfaceDisplaying the current system time Configuring the network time Calendar Configuring the time zone and daylight saving time Source Interface Date and time configuration example This example, Device a is the firewall Configuring the local clock as the reference clock Configuring the system time at the CLI Configuration guidelines Zone-offset System time configuration resultsDate-time Date-time ± zone-offset Zone-offset + Summer-offset To change the system timeDate-time ± zone-offset + Both date-time Setting the idle timeout timer at the CLI Setting the idle timeout timer in the Web interfaceTo set the idle timeout timer Enabling displaying the copyright statement Configuring bannersTo enable displaying the copyright statement Banner message input modes Configuring the maximum number of concurrent users To configure banners Rebooting the device Configuring the exception handling methodRebooting the firewall in the Web interface Rebooting devices immediately at the CLI Rebooting the firewall at the CLIScheduling a device reboot Scheduling jobs Job configuration approachesComparison of non-modular and modular approaches Job job-name Scheduling a job in the non-modular approachScheduling a job in the modular approach View view-name Time time-id at time date command command Scheduled job configuration example# Create a job named pc1, and enter its view # Create a job named pc3, and enter its view Setting the port status detection timer# Create a job named pc2, and enter its view # Display information about scheduled jobs Configuring advanced temperature thresholds Configuring temperature thresholds for a device or a moduleConfiguring basic temperature thresholds To set the port status detection timer Monitoring an NMS-connected interface Clearing unused 16-bit interface indexes Diagnosing transceiver modules Verifying and diagnosing transceiver modulesVerifying transceiver modules Interface-number begin Displaying and maintaining device management Command ReferenceSee Getting Started Task Command Remarks Task Command Remarks Managing users Configuring a local user in the Web interfaceUser levels Configure a local user, as described in Table Click Apply Click Add Service type feature and hardware compatibility Configuration exampleItem Description Controlling user logins Configuring a local user at the CLIConfiguring Telnet login control Vpn-instancevpn-instance-name Configuring source IP-based Telnet login controlSource sour-addr sour-wildcard Ipv6-address prefix-length Configuring source MAC-based Telnet login control Telnet login control configuration exampleRule-string Configuring source IP-based Snmp login control Getting Started Read-view write-viewwrite-view Snmp login control configuration exampleIpv6 ipv6-acl-number Group-name acl acl-number acl ipv6 Configuring Web login control Configuring source IP-based Web login control Source sour-addr sour-wildcard N/A any time-range Web login control configuration exampleLogging off online Web users User-id user-nameuser-name Displaying online users Field Description Command conventions Using the CLICommand conventions Convention Description Using the undo form of a command CLI views Returning to the upper-level view from any view Task CommandEntering system view from user view Returning to user view from any other view Accessing the CLI online help Abbreviating commands Entering a commandEditing a command line Command line editing keys To configure a command keyword alias Configuring and using command keyword aliasesConfiguring and using hotkeys Usage guidelines System-reserved hotkeys Enabling redisplaying entered-but-not-submitted commandsHotkey Function Common command-line error messages Understanding command-line error messagesUsing the command history function Error message Cause Pausing between screens of output Viewing history commandsSetting the command history buffer size for user interfaces Controlling the CLI output Special characters supported in a regular expression Filtering the output from a display commandCharacter Meaning Examples String1string2string1string2 Contain stringstring. string1string2\2 repeatsString1string2string2. string1string2\1\2 Matches character1character2 Configuring user privilege and command levels A being character2, but does not match 2a Command levels and user privilege levels Configuring a user privilege levelLevel Privilege Default set of commands Management and Maintenance Last-num1 vty first-num2 Last-num2 By default, the user privilege level Switching the user privilege level Authentication mode Keywords Description Privilege level switching authentication modesInformation, see Access Control Configuration Guide Switching to a higher user privilege level Information required for user privilege level switching To change the level of a command Saving the running configurationChanging the level of a command View command Contacting HP Support and other resourcesRelated information Conventions Command conventionsSymbols GUI conventions Network topology icons Port numbering in examples Index 144