(continued)
001(continued)
– | the system unit whenever removing or replacing FRUs. |
| |||||||||
– Remove | all | adapter | cards, except for | the | modem | adapter | |||||
card and | any IBM Aptiva |
|
| ||||||||
– Remove | all | telephone | cables | from | the Modem. |
|
|
|
| ||
– Disconnect | any | drives except: |
|
|
|
|
|
| |||
diskette | drive |
|
|
|
|
|
|
| |||
Hard disk | drive | (some machines can have up | to 3 | hard | disk | drives | |||||
plus | a |
|
|
|
|
| |||||
IBM | Aptiva | (such as | a | ||||||||
– Ensure | all | power cords and cables are connected properly. |
|
| |||||||
– Ensure | the | monitor brightness | and | contrast controls | are | not turned | down. | ||||
–Ensure the sound volume control is not turned down and the speakers are connected.
–
| Note: | Some monitors have a detachable system I/O signal cable |
| |||||||||||||||||||||||||
|
|
|
|
| between | the | monitor | and | the | system | unit. In |
| either | case, | check | |||||||||||||
|
|
|
|
| the power cord or cable before replacing the unit. See |
| ||||||||||||||||||||||
|
|
|
|
| “Detachable Monitor | I/O Signal Cable Connector Test Points” on |
| |||||||||||||||||||||
|
|
|
|
| page | for | pin | identification. |
|
|
|
|
|
|
|
|
| |||||||||||
– Ensure correct monitor refresh rate. See “Refresh Rates and Monitor | ||||||||||||||||||||||||||||
| Frequencies” | on | page |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
– Note |
| any | symptoms, | messages, | error | codes, | or | beeps. |
|
|
| |||||||||||||||||
– Make |
| sure | there | are | no | diskettes | or | CDs | in the | drives. |
|
| ||||||||||||||||
– For |
| Home |
| Automation | checkout, | see | “Home | Director” | on | page |
| |||||||||||||||||
DOES | THE | SYSTEM | COMPLETE | POST | WITH |
| NO | ERRORS |
| AND | DOES |
|
|
|
|
|
|
|
|
| ||||||||
AN | IBM |
| APTIVA |
| SOFTWARE | SCREEN | APPEAR? |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
Note: |
| If | Suspend | Timer | is | enabled, |
| answer | this | question | “No.” |
| ||||||||||||||||
Yes |
|
| No |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 002 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||||
|
|
| – If |
| Suspend | Timer | is | enabled, | you | must | disable | Suspend | Timer | in | ||||||||||||||
|
|
|
|
| the |
| Setup Utility, | and enable it again upon | completion | of service. | ||||||||||||||||||
|
|
|
|
| To | disable | Suspend | Timer: |
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
| 1. Make | sure | the | customer | saves | and | closes | any | open | files. | ||||||||||||||
|
|
|
|
| 2. | then | unit. |
|
|
|
|
| ||||||||||||||||
|
|
|
|
| 3. | PressF1 | while | the | POST | Configuration |
| icon | is |
| displayed. |
| ||||||||||||
|
|
|
|
| 4. | In | the | Setup |
| Utility | Main | Menu, | select Power | Management | and | |||||||||||||
|
|
|
|
|
|
| pressEnter . |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
| (Step 002 | continues) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
