(continued)
006(continued)
ARE | THE | VOLTAGES | CORRECT | AND | DOES | THE | FAN RUN? |
|
|
|
|
|
| |||||||
Yes |
|
| No |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| 007 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
| Replace | the | power | supply. |
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
008 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| ||||||||||||||
– The | power | supply is working normally. (If you suspect the | on/off | switch | ||||||||||||||||
| cable assembly, see Step 009.) If the fan continues to run | when | all | |||||||||||||||||
| connectors | are |
| plugged | back in, go to “Undetermined Problem” on |
| ||||||||||||||
| page | If | the | fan | stops | running when | a drive | connector | is plugged | |||||||||||
| back | in, | go | to | Drive | Devices” | on page |
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
009 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
(From | steps | 003 | and | 008) |
|
|
|
|
|
|
|
|
| |||||||
DOES | THE | SYSTEM | UNIT | FAIL TO | SHUT | OFF | WHEN | THE | ON/OFF |
|
|
|
|
| ||||||
SWITCH |
| IS | PRESSED? |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
Yes |
|
| No |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
010
Go to Step 006 on page
011 |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |||||
– You | might | have | a | failing | on/off | switch cable assembly. | ||||||
– Disconnect | the | on/off | switch | cable assembly connector from the power | ||||||||
| supply | connector | and | take | an | ohm | reading. | |||||
DO | YOU | HAVE | AN | OHM | READING | WHEN THE | SWITCH | IS | PRESSED | |||
AND | AN | OPEN | READING | WHEN | THE | SWITCH IS | RELEASED? |
| ||||
Yes | No |
|
|
|
|
|
|
|
|
| ||
012
– Replace the on/off switch cable assembly.
013
– Replace the system board.
