Intel IQ80321 B.7 Running the Code|Lab Debugger

96 Board Manual

Intel® IQ80321 I/O Processor Evaluation Platform

Getting Started and Debugg er

B.7 Running the Code|Lab Debugger

This section is provided to get the s ystem up and running in the Code| Lab Debug environment, but it

is not intended as a full-functional tutorial. Please refer to the ATI Code |Lab Debug Reference

Manual for more detailed information.

B.7.1 Launching and Configuring Debugger

1. In EDE, click on the icon that looks like a red bug.

a. The “Connect” dialog appears.

2. When not configured from SectionB.4.2, “Using Flash Programmer”, go to Section B.4.2 and

perform steps 2-5.

3. When running version 1.5 of the Code|Lab Debugger or earlier, a script must be specifie d

under the “Configure Macraigor JTAG Connection” Window:

a. Check the Script Options box

b. hit Browse

c. then lo c ate the following :

”C:\Ati\boards\IQ80321\Plus\Demo\Init_IQ80321.vbs”

d. hit OK

Note: This script adds delay between the JTAG initialization and the launching of RedBoot so that the

boot is successful after hitting Go.

4. Press Connect to enter debug mode.

a. The Code|Lab Debug environment appears with the Assembly window open.

Note: Mouseovers are available for most of the toolbar icons. (Leave the mouse over the debug icons

across the top on the toolbar to see a brief explanation of each.)

5. Click on the go icon and let RedBoot boot (takes a minute) until you get the RedBoot

prompt “RedBoot>” in the Console window (cl ick the Console tab at the bottom of the Debug

window to view the Console window).

6. From the console window:

a. type “diag”.

b. hit “Enter”.

The RedBoot Diagnostic function is invoked.

Try out a few of the tests as desired.

7. Close the Debugger and EDE environment.

8. Reset the board (cycle power).

Contents

Main Intel IQ80321 I/O Processor Evaluation Platform Contents Page Page Page Page Figures Tables Page Revision History Page Introduction 1 1.1 Document Purpose and Scope 1.2 Related Documents Introduction 1.3 Electronic Information Tabl e 3 provides additional information on th e major components of IQ80321. 1.4 Component References Table 2. Electronic Information Table 3. Component Reference 1.5 Terms and Definit ions 1.6 Intel 80321 I/O Processor Page Introduction 1.7 Intel IQ80321 Evaluation Platform Board Features Table 5. Summary of Features Getting Started 2 2.1 Kit Content 2.2 Hardware Installation 2.2.1 First-Time Installation and Test 2.3 Factory Settings 2.4 Development Strategy 2.4.1 Supported Tool Buckets 2.4.2 Contents of the Flash 2.5 Target Monitors 2.5.1 Redhat Redboot 2.5.2 ARM Firmware Suite Page Getting Started 2.6 Host Communications Examples Server/Desktop/Backplane e l b 2.6.3 JTAG Debug Communication Using a JTAG Emulator: Figure 4. JTAG Debug Communication 2.6.4 GNUPro GDB/Insight Page Page 2.6.5 ARM Extended Debugger Page Hardware Reference Section 3 3.1 Functional Diagram Figure 5 shows the functional block for the IQ80321 . Figure 5. Functional Block Diagram Intel IQ80321 I/O Processor Evaluation Platform 3.2 Board Form-Factor/Connectivity DDR DIMM Connector Battery Intel Figure 6. Board Form Factor 3.3 Power 3.4 Memory Subsystem 3.4.1 DDR SDRAM 3.4.1.1 Battery Backup 3.4.2 Flash Memory Requirements Page 3.6 Interrupt Routing 3.7 Intel IQ80321 Evaluation Platform Board Peripheral Bus The IQ80321 populates the per ipheral bus as depicted by F igure8. The devices on the bus include Flash ROM, UART, HEX display, and rotary switch. Figure 8. Intel IQ80321 Evaluation Platform Board Peripheral Bus Topology Table 11. Peripheral Bus Features 3.7.1 Flash ROM Table 12. Flash ROM Features Figure 9. Flash Connection on Periphera l Bus 3.7.2 UART Table 13. UART Features Figure 10. UART Connection on the Peripheral Bus 3.7.3 H EX Display Table 14. HEX Display on the Perip heral Bus Figure 11. HEX Display Connection on the Peripheral Bus 3.7.4 Rotary Switch 3.7.5 Battery Status Table 16. Battery Status Buffer Requirements Figure 13. Battery Status Buffer on Peripheral Bus 3.8 Debug Interface 3.8.1 Console Serial Port 3.8.2 Ethernet Port 3.8.2.1 Intel 82544EI Gigabit Ethernet Controller 3.8.3 JTAG Debug 3.8.3.1 JTAG Port 3.8.4 Logic-Analyzer Connectors 3.8.5 Mictor J3F2 3.8.6 Mictor J2F1 3.8.7 Mictor J1C1 3.8.8 Mictor J3C1 3.8.9 Mictor J2C1 3.9 Board Reset Scheme TRST Pin Figure 15. RESET Sources Reset from Primary PCI-X Connector To PCI-X Bridge Reset 3.10 Switches and Jumpers 3.10.1 Switch Summary Table 24. Switch Summary 3.10.2 PCIX Initialization Summary 3.10.2.1 User Defined Switches PCI-X 100/133 PCI-X 66 3.10.2.2 PCI-X Bridge Initialization Signals 3.10.3 Default Switch Settings - Visual Table 25. Switch S7E1 Table 26. Switch S8E1 Table 27. Switch S8E2 Table 28. Switch S9E1 3.10.4 Jumper Summary 3.10.5 Connector Summary 3.10.6 General Purpose Input/Output Header 3.10.7 Secondary PCI/PCI-X Operation Settings 3.10.8 Primary PCI/PCI-X Operation Settings Table 34. Secondary PCI/PCI-X Operation Settings Table 35. Primary PCI/PCI-X Operation Settings 3.10.9 Detail Descriptions of Switches/Jumpers 3.10.9.1 Switch S7E1- 2/3 3.10.9.2 Switch S7E1- 4/5 3.10.9.3 Switch S7E1- 6/7 3.10.9.4 Switch S7E1- 8 3.10.9.5 Switch S8E1- 2 3.10.9.6 Switch S8E1- 3 3.10.9.7 Switch S8E1- 4 3.10.9.8 Switch S8E1- 5 3.10.9.9 Switch S8E1- 6 3.10.9.10 Switch S8E1- 7 3.10.9.11 Switch S8E1- 8 3.10.9.12 Switch S8E2 - 1/2 3.10.9.13 Switch S8E2 - 4 3.10.9.14 Switch S9E1 - 1:3 3.10.9.15 Switch S9E1 - 4 3.10.9.16 Switch S1D1 - 1/2 3.10.9.17 Switch S4D1 - 1/2 3.10.9.18 Switch S4D1 - 3/4 3.10.9.19 Jumper J1G2 3.10.9.20 Jumper J3E1 3.10.9.21 Jumper J3G1 3.10.9.22 Jumper J9E1 3.10.9.23 Jumper J9F1 Page External RAID Section 4 4.1 Private Device Configuration Figure 17. IDSEL Routing for Private Device Configuration External RAID Section 4.2 Interrupt Routing Figure 18. Interrupt Routing for Private Device Configuration Intel 80321 I/O Processor Software Reference 5 5.1 DRAM 5.2 Components on the Peripheral Bus 5.2.1 Flash ROM 5.2.2 UART 5.2.3 Rotary Switch 5.2.4 HEX Display Page 5.3 Ethernet Software Reference 5.4 Board Support Package (BSP) Examples 5.4.1 Intel 80321 I/O Processor Memory Map Software Reference 5.4.2 Redboot* Intel IQ80321 Memory Map The virtual memory maps use a C, B, and X column to indicate the caching policy for the region. 5.4.3 Redboot Intel IQ80321 Physical Memory Map - Visual 5.4.4 Redboot Intel IQ80321 Virtual Memory Map - Visual 5.4.5 Redboot Intel IQ80321 Files 5.4.6 Redboot Intel IQ80321 DDR Memory Initialization Sequence 5.4.7 Redboot Switching Page IQ80310 and IQ80321 Comparisons A Page Getting Started and Debugger B B.1 Introduction B.1.1 Purpose B.1.2 Necessary Hardware and Software B.1.3 Related Documents B.1.4 Related Web Sites B.2 Setup B.2.1 Hardware Setup B.2.2 Software Setup B.3 New Project Setup B.3.1 Creating a New Project B.3.2 Configuration B.4 Flashing with JTAG B.4.1 Overview B.4.2 Using Flash Programmer B.5 Debugging Out of Flash B.6 Building an Executable File From Example Code B.7 Running the Code|Lab Debugger B.7.1 Launching and Configuring Debugger B.7.2 Manually Loading and Executing an Application Program B.7.3 Displaying Source Code B.7.4 Using Breakpoints B.7.5 Stepping Through the Code B.7.6 Setting Code|Lab Debug Options B.8 Exploring the Code|Lab Debug Windows B.8.1 Toolbar Icons B.8.2 Workspace Window B.8.3 Source Code B.8.4 Debug and Console Windows B.8.6 Registers Window B.8.7 Watch Window B.8.8 Variables Window B.9 Debugging Basics B.9.1 Overview B.9.2 Hardware and Software Breakpoints B.9.2.1 Software Breakpoints B.9.2.2 Hardware Breakpoints B.9.3 Exceptions/Trapping Page Getting Started and Debugger C C.1 Introduction C.1.1 Purpose C.1.2 Necessary Hardware and Software C.1.3 Related Documents C.1.4 Related Web Sites C.2 Setup C.2.1 Hardware Setup C.2.2 Software Setup C.3 New Project Setup C.3.1 Creating a New Project C.3.2 Configuration File Project code|lab EDE Tools Help Edit View Build, Debug C.4 Flashing with JTAG C.4.1 Overview C.4.2 Using Flash Programmer C.5 Debugging Out of Flash C.6 Building an Executable File From Example Code C.7 Running the Code|Lab Debugger C.7.1 Launching and Configuring Debugger C.7.2 Manually Loading and Executing an Appli cation Program C.7.3 Displaying Source Code C.7.4 Using Breakpoints C.7.5 Stepping Through the Code C.7.6 Setting Code|Lab Debug Options C.8 Exploring the Code|Lab Debug Windows C.8.1 Toolbar Icons C.8.2 Workspace Window C.8.3 Source Code C.8.4 4 Debug and Console Windows C.8.6 Registers Window C.8.7 Watch Window C.8.8 Variables Window C.9 Debugging Basics C.9.1 Overview C.9.2 Hardware and Software Breakpoints C.9.2.1 Software Breakpoints C.9.2.2 Hardware Breakpoints C.9.3 C.9.3 Exceptions/Trapping