Problems following Initial System Installation

Problems that occur at initial system startup are usually caused by an incorrect installation or configuration. Hardware failure is a less frequent cause. If the problem you are experiencing is with a specific software application, see “Problems with Newly Installed Application Software”.

First Steps Checklist

•Is AC power available at the wall outlet?

•Are the power supplies plugged in? Check the AC cable(s) on the back of the chassis and at the AC source.

•Are all cables correctly connected and secured?

•Are the processors fully seated in their sockets on the server board?

•Are all standoffs in the proper location and not touching any components, causing a potential short?

•Are all add-in PCI boards fully seated in their slots on the server board?

•Are all jumper settings on the server board correct?

•Are all jumper and switch settings on add-in boards and peripheral devices correct? To check these settings, refer to the manufacturer's documentation that comes with them. If applicable, ensure that there are no conflicts-for example, two add-in boards sharing the same interrupt.

•Are all peripheral devices installed correctly?

•If the system has a hard disk drive, is it properly formatted or configured?

•Are all device drivers properly installed?

•Are the configuration settings made in Setup correct?

•Is the operating system properly loaded? See the operating system documentation.

•Did you press the system power on/off switch on the front panel to turn the server on (power on light should be lit)?

•Is the system power cord properly connected to the system and plugged into a NEMA 5 15R outlet for 100-120V or a NEMA 6-15R outlet for 200-240V ?

•Are all integrated components from the tested components lists? Check the tested memory, and chassis lists, as well as the supported hardware and operating system list. See “Server System References” for links to the tested component lists.

Hardware Diagnostic Testing

This section provides a more detailed approach to identifying a hardware problem and locating its source.

112

Intel® Server System SR2500AL User’s Guide

Page 133 Page 135
Page 134
Image 134
Intel SR2500AL manual Problems following Initial System Installation, Hardware Diagnostic Testing, First Steps Checklist
Page 133 Page 135

SR2500AL specifications

The Intel SR2500AL is a high-performance server chassis designed to support a wide range of enterprise applications. Built on Intel's robust architecture, it aims to deliver exceptional efficiency, reliability, and flexibility, which are paramount in a modern data center environment.

One of the main features of the SR2500AL is its versatility in supporting various Intel server motherboards and processor configurations. The chassis can accommodate dual Intel Xeon processors, thereby enabling high levels of processing power suitable for multi-threaded applications. This dual-processor support is crucial for businesses that require high-performance computing capabilities for tasks such as data analytics, virtualization, and cloud computing.

The SR2500AL supports up to 16 DIMM slots, allowing for substantial memory capacity. This flexibility is crucial for applications that require a large amount of RAM to function efficiently, thereby minimizing bottlenecks and enhancing overall system performance. Furthermore, the chassis supports a wide variety of memory types, including ECC (Error-Correcting Code) memory, which enhances system reliability by detecting and correcting common data corruption issues.

In terms of storage, the SR2500AL provides multiple drive bays that can support SAS (Serial Attached SCSI) and SATA (Serial ATA) drives, offering IT administrators the flexibility to configure their storage solutions according to their specific requirements. The server can be configured with both traditional spinning hard drives and solid-state drives, allowing for tailored performance and storage capacity that meets diverse business needs.

Cooling is another critical aspect of the SR2500AL's design. It features advanced thermal management technologies to maintain optimal operating temperatures, thus enhancing the longevity and reliability of the components housed within. The chassis includes multiple strategically placed fans and airflow optimization features that help in the efficient dissipation of heat.

Connectivity is also a strong point for the SR2500AL. It offers a variety of network interface options, enabling seamless data transfer and integration into existing network infrastructures. The chassis can support both Gigabit Ethernet and 10GbE (10 Gigabit Ethernet) networking options, ensuring that businesses can achieve the bandwidth required to maintain high-performance operations.

Overall, the Intel SR2500AL combines powerful processing capabilities, extensive memory support, flexible storage options, and advanced cooling solutions, making it an ideal choice for businesses looking to enhance their infrastructure. With its robust design and thoughtful features, the SR2500AL stands out as a reliable server solution in the demanding landscape of modern enterprise computing.
Top Page Image Contents