![](/images/new-backgrounds/1197974/197974195x1.webp)
Diagnostics and Troubleshooting
Error | Error Message | Possible Cause | Possible Solution | |
Code | ||||
|
|
| ||
|
|
|
| |
92 | knife back not detected | Knifeback switch was not detected | Check for a paper jam at the knife | |
|
| after moving knife from front to | area. | |
|
| back. |
| |
|
|
|
| |
93 | translator power fault | A power fault was detected by the | Close all doors and reinitialize the | |
| error | translator puck. | printer. | |
|
|
|
| |
95 | unexpected shoe exit | The shoe exit nip made switch was | Check for a paper jam in the shoe | |
| nip detected | detected after moving the shoe exit | exit nip area. | |
|
| nip to the nip unmade position. |
| |
|
|
|
| |
96 | shoe exit nip made not | The shoe exit nip made switch was | Check for a paper jam in the shoe | |
| detected | not detected after moving the shoe | exit nip area. | |
|
| exit nip to the nip made position. |
| |
|
|
|
| |
97 | unexpected deflector | The deflector nip made switch was | Check for a paper jam in the | |
| nip made | detected after moving the deflector | deflector nip area. | |
|
| to the up position. |
| |
|
|
|
| |
98 | deflector nip made not | The deflector nip made switch was | Check for a paper jam in the | |
| detected | not detected after moving the | deflector nip area. | |
|
| deflector to the up position. |
| |
|
|
|
| |
99 | timeout clearing data | The rotor was not able to be | Call for service. | |
| patch | properly started. |
| |
|
|
|
| |
100 | xlator start failed | The translator failed to start. | Call for service. | |
|
|
|
| |
101 | shoe exit nip start failed | The shoe exit nip failed to start. | Call for service. | |
|
|
|
| |
102 | deflector start failed | The deflector failed to start. | Call for service. | |
|
|
|
| |
109 | sheet xport ready | The sheet transport area remains | Call for service. | |
| timeout | busy or initializing process is taking |
| |
|
| longer than expected. |
| |
|
|
|
| |
110 | paper detected in | Paper was detected in the printer | Remove all paper from the printer | |
| machine | while attempting to load a new roll | and reload the new roll of paper. | |
|
| of paper. |
| |
|
|
|
| |
111 | xlator home failed | The translator could not find its | Call for service. | |
|
| home position after several |
| |
|
| attempts. |
| |
|
|
|
| |
112 | invalid paper width | The paper is not laying flat over the | Open the supply door and move the | |
| sensor coverage | paper width sensors or the end of | paper to the correct position. | |
|
| roll has been reached. |
| |
|
|
|
| |
128 | back checksum 0 | ROM test failed at powerup. | Reinitialize the printer and call for | |
|
|
| service. | |
|
|
|
| |
129 | bad checksum 1 | RAM test failed at powerup. | Call for service. | |
|
|
|
| |
130 | rotor not stopping | Rotor will not turn off. | Turn off the printer and call for | |
|
|
| service. | |
|
|
|
| |
131 | xlator at both limits | Both the front and back translator | Call for service. | |
|
| soft limit switches are actuated. |
| |
|
|
|
|
October 2002 |