Korg HDR-TRI Specications

Specifications

57

IntroductionOperationParametersAppendix

Speciﬁcations

INPUT/OUTPUT connectors: SCSI connector, ANALOG IN 1/2 connectors, S/

P DIF IN/OUT connectors

Sampling frequency: 48 kHz

Recording time: when using a 540 Mbyte hard disk, approximately 94 minutes

of monaural recording, approximately 47 minutes of stereo recording (approxi-

mately 5 Mbytes per minute of monaural recording)

Tracks recorded simultaneously: 2

Tracks played back simultaneously: 4

Digital mixer speciﬁcations

Volume: 0—127 (100=unity)

High EQ: –15—+15 (0=unity)

Low EQ: –15— +15 (0=unity)

Send 1: 0—127 (send to Master Effect 1)

Send 2: 0—127 (send to Master Effect 2)

Pan: L000—C064—R127, OFF

Analog audio input gain structure

S/N ratio (A-weighted): better than 90 dB

Measured at OUTPUT 1 and 2 for a 1 kHz sine wave input, Rec Level=0.0,

AT1: Pan=L000, Volume=100, AT2: Pan=R127, Volume=100, AT3/4: MUTE

Action: Lower the Input Level and/or Rec Level settings so that the Over-

load and/or Over displays do not appear.

Cause 2: Even if the Input Level and Rec Level settings are appropriate, dis-

torted sound will be output from the monitor if the P1 tab 6 page

(Mix Audio Track 1–4) Volume setting is too high. (However the

sound that is recorded is not distorted.)

Action: Adjust the volume downward. A volume setting of 0 is -inﬁnity, 100

is 0 dB, and 127 is +127 dB.

Cause 3: In situations other than the above, the output from the monitor will

be distorted if Pan is set to C064 during stereo recording.

Action: During stereo recording, set Pan to L000 and R127.

Problem: Sound is not output from the monitor even though the level meters

are up.

Cause 1: There is a problem with the settings of the TRINITY itself or with the

connections.

Action: Raise the TRINITY’s volume, or check the monitor connections.

Cause 2: An audio track is not selected in Track.

Action: Select an audio track.

Cause 3: Even if an audio track is selected, the tab 6 page (Mix A1–4) Volume

setting is 0, or Pan is OFF.

Action: Adjust the Volume and Pan settings.

Input Level setting Typical input level Max input level Typical gain

–30 dBu –30 dBu –20 dBu +20 dB

–10 dBu –10 dBu 0 dBu 0 dB

+4 dBu +4 dBu +14 dBu –14 dB

Contents

Main Table of Contents 3. Parameters 2. Operation 1. Introduction 4. Appendix 1. Introduction About hard disk recording Features of the HDR-TRI About hard disks About sound and audio events 2. Operation Hard disk connections and settings Settings for recording Formatting a hard disk Types of SCSI devices that can be connected and their ID settings Connections for recording Song settings 8 16 4 Checking the external input Page Recording Recording an audio track Recording a guitar in stereo on tracks 3 and 4 while listening to audio tracks 1 and 2 Checking the external input The Compare function Playback Playing back the track(s) you recorded Adjusting the pan or volume balance of the tracks Recording mixer events Re-recording Using the rehearsal function Using auto punch-in recording to edit Editing Creating repetitions of the same phrase Track bouncing (ping-pong recording) Bouncing MIDI tracks and audio tracks together Applying master effects Creating a song in conjunction with the MIDI sequencer Recording the vocal Checking the external input Recording Adjusting the balance and equalizer for the monitor output Using effect processing Recording mixer events Saving/loading recorded data Saving song data to a hard disk Loading data from a hard disk 20 2 Using a recorded sound more than once in the same .SNG le Creating different arrangements using the same vocal Using the same sound more than once 21 3. Parameters Tempo Mode 15c: Tempo/Tempo Mode 15: Audio Track Rec Multi Rec 15d: Track [T01...16, MTR, AT1(L), AT2(R), AT3(L), AT4(R), AT1&2, AT3&4, MIXER REC] 15e: Meter/Metronome/Resolution/Multi Rec/Remove Data 15f: Take 15h: Rehearsal 15g: Take Number 15i: Input Select [Analog, Digital] 15j: Input Level [+4 dBu, 10 dBu, 30 dBu] ...+18 dB] 15k: Rec Level [ 15l: Audio Track Name Display 25 15D: Rec HD Select 15m: Monitor Mode Select 26 L (Low EQ) [15...0...+15] 16g: Send1/Send2 [0...127] H (High EQ) [15...0...+15] 16: Mix Audio Track 14 16i: Volume [0...100...127] 16j: Mix Audio Track Mode [MANUAL/READ/MUTE/SOLO/WRITE] Page 17: Preference 17h: Recording Setup 25D: Rec HD Select Sequencer P2 25c: Delay [0...255 samples/0...5 ms] 25: Audio Track parameter (Audio Track 14) Sequencer P5 AT1&2, AT3&4, MIXER REC] 53d: Track [T01...16, MTR, AT1(L), AT2(R), AT3(L), AT4(R), 53: Audio Track Edit 32 53B: Automation Edit 4 1 2 33 5 A: Insert button B: Delete button C: Copy button Page 35 4 53F: Delete Measure 1 2 36 53G: Insert Measure 1 2 3 37 53H: Copy Measure 4 5 6 1 2 38 53I: Move Measure 1 2 3 4 39 53J: Audio Event Edit 1 2 3 Page Page Page Page 44 54: Audio Track Name 54j: Audio Track Name 54B: Automation Edit 54C: Erase Audio Track 54D: Copy Audio Track 45 54F: Delete Measure 54G: Insert Measure 54H: Copy Measure 54I: Move Measure Disk P1 11: Load 13: Utility 48 13G: Format 13H: Wipe 1 2 3 Page 50 14: Audio Utility 14B: Backup to DAT 1 2 3 Page Page Page Page Page 56 Messages Troubleshooting Specications