Language Selection, System Options | Liebert 610 specs

Operation

Language Selection

English and Portuguese are supported.

System Options

This screen enables and disables optional features which might or might not be installed in your UPS. The options are Customer Alarm Interface, Battery Exercise, Temperature-Compensated Battery Charging, Automatic Restart and Continuous Duty Static Switch. LCD contrast and backlight bright- ness can be set to desired levels. To enable or disable an option, do the following:

1.From the System Configuration screen, press the Up or Down pad to move the highlighted cursor to System Options.

2.Move to and select option you wish to enable or disable.

3.Press the Up or Down pad to toggle between enabled or disabled.

4.Press the Select pad to set the desired status.

Once enabled, the Customer Alarm Interface and the Battery Exercise options become entries on the Master Menu and can be controlled from there.

For more information about these options, refer to 3.4.5 - Battery Exercise Procedures and 3.5.5 - Automatic Restart (Optional).

Figure 25 System options screen

		UP: CURSOR UP
		DOWN: CURSOR DOWN
		SELECT: CHOOSE
	SYSTEM OPTIONS

EXIT
LCD Contrast
Backlight Brightness
Customer Alarm Interface Board		NO
Battery Temp. Compensated Charging		NO
Auto Restart Enabled		NO
Battery Test		YES
Continuous Duty Static Switch		YES

37

Image 43

Liebert 610 manual Language Selection, System Options

Contents

Series 610 UPS Battery Cabinet Precautions Table of Contents Specifications Maintenance Figures Tables Important Safety Instructions System Description Designed for Success ReliabilityOther Factors to Consider Safety Precautions Modes of Operation Operator Controls Options Automatic Restart Customer Alarm InterfaceTemperature-Compensated Charging Battery Load Testing General Component Descriptions Battery PlantUPS Module Controls Hardware Detailed Component DescriptionsSoftware Input Circuit Breaker Input Power FactorRectifier/Charger Operation Battery Equalize Charge Circuit Battery Charging CircuitBattery Disconnect Battery Charge Current Limiting Output Regulation and Overload Performance Non-Linear Load CharacteristicsUnbalanced Load Characteristics Inverter Pulsed Parallel Operation Static Switch Backfeed ProtectionStatic Bypass Bypass Circuit Breaker Transfer and Retransfer Conditions Three Breaker Maintenance Bypass Switchboard Display Screen and Operator Controls Features 100kVA 500kVA 1000kVA Description Function Operator controls, typical system Description Function Series 610 UPS operator control panel Menu tree Menu Tree Navigation Master menu screen Master Menu Screen Operation Input Metering Displays Monitor/Mimic Display ScreenOutput Metering Displays Item 7 Alarm Messages Status/Alarm Message AreasItem 6 Status Messages Monitor/Mimic display example Utility fail Walk-in display screen Walk-In Display Screen Status reports screen Status Reports Screens Event History Present Status History status report screen History Status System Status Battery Cycle Monitor Battery cycle monitoring summary screen System configuration screens System Configuration Screens Maximum auto-retransfer attempts screen Maximum Auto-Retransfer Attempts Date screen Date Time screen Time Auto dial screen Auto Dial System Options Language Selection Continuous Duty Static Switch Optional Standard Remote Monitor Indications Channel Alarm messagesAdditional alarm messages Remote Monitor Low Battery Alarm Limit Settings ScreenOverload Alarm Battery Discharging Temperature Limit Setting Optional Battery Shutdown 60 MinutesBattery Rating 100% Battery Rating Load transfer procedure screen Load Transfer Procedures Screen Refer to 3.4.1 Start-Up Procedure for more details Start-Up Procedures Screen Battery Time Screen Shutdown Procedures Screen Battery time screen 15-minute discharge Elapsed Time Minutes Upper Limit Actual Lower Limit Status Reports Screens Meter Calibration Screen Battery equalize screen Battery Equalize Screen Alarm and status message screen Alarm and Status Messages Status Messages Abbreviations used in alarm messages Alarm Messages AC Input Alarm messages and corrective actions UPS System Cooling UPS System Alarm Message Special Functions Alarm messages-summary Worldwide Reporting Communication InterfacesAuto-Dial Requesting Information Local Reporting to a TerminalLocal Reporting to a Monitor Site Reporting SiteScan or Snmp Keys Function Series 610 terminal commandsRemote Monitor Panel Separate / Simultaneous Outputs Circuit breaker abbreviations Load on BypassAbbreviation Circuit Breaker Load on bypass UPS available OK to Transfer Load on UPS bypass available Momentary Overloads Momentary overload through pulse-parallel static switch Input power fail-load on battery Input Power Failure-Load on Battery Load on UPS-battery not available Off Battery Emergency Module Off Refer to 3.4.4 Shutdown Procedures Emergency power off Remote Emergency Power Off Module Shutdown Refer to 3.3.9 Maintenance Bypass Load on maintenance bypass two breakers Load on maintenance bypass three breakers Start-Up Procedure Manual Procedures Start-Up Procedure Set the Static Switch Disconnect or to OFF open Start-up procedures Start-Up Procedure Load transfer procedures screen Load Transfer Procedures Maintenance Bypass Load Transfers Shutdown Procedures Shutdown Procedures Module Shutdown Procedure Local Emergency Modules Off Lemo Remote Emergency Power Off Repo Battery exercise control screen above and results below Battery Exercise Procedures 150% Automatic OperationsOverloads Without Transfer 1000% Automatic Retransfers to UPS Automatic Transfers to Bypass Overload Condition Automatic Transfers to Bypass UPS System Faults Enabling Automatic Restart Automatic Restart OptionalSequence of Operation Maintenance Training Liebert Global ServicesMaintenance Agreements The Signature Program Professional Start-Up Record Log Routine MaintenanceAir Filters Limited Life Components Battery Safety Precautions Battery Maintenance Avertissement Number of Cells Battery Voltage VDC Nominal Float Matching Battery Cabinets Optional Battery voltage record Battery retorque valuesRack-Mounted Batteries Detection of Trouble Torque specifications unless otherwise labeledTorque Requirements Recommended Test Equipment Reporting a ProblemUpstream Feeder Circuit Breaker Setting Inspections Corrective Actions Rating Power factor pf KVAKVA Environmental Conditions Specifications applicable to environment Battery Operation Adjustments Electrical Specifications Page United States Technical Support/ServiceCompany Behind the Products Locations