Manuals / Liebert / Computer Equipment / Power Supply

Liebert 610 manual Battery Cabinet Precautions

Models: 610

1 104

Download 104 pages 35.06 Kb

Page 2

BATTERY CABINET PRECAUTIONS

The following warning applies to all battery cabinets supplied with UPS systems. Additional warn- ings and cautions applicable to battery cabinets may be found in Important Safety Instructions and 4.4 - Battery Maintenance.

! WARNING

Internal battery strapping must be verified by manufacturer prior to moving a battery cabinet (after initial installation).

•Battery cabinets contain non-spillable batteries.

•Keep units upright.

•Do not stack.

•Do not tilt.

Failure to heed this warning could result in smoke, fire or electric hazard.

Call 1-800-LIEBERT prior to moving battery cabinets (after initial installation).

CONTACTING LIEBERT FOR SUPPORT

To contact Liebert Global Services for information or repair service in the United States, call

1-800-LIEBERT (1-800-543-2378). Liebert Global Services offers a complete range of start-up services, repair services, preventive maintenance plans and service contracts.

For repair or maintenance service outside the 48 contiguous United States, contact Liebert Global Services, if available in your area. For areas not covered by Liebert Global Services, the authorized distributor is responsible for providing qualified, factory-authorized service.

For LGS to assist you promptly, please have the following information available:

Part numbers: _________________________________________________________________

Serial numbers:________________________________________________________________

kVA Rating: ___________________________________________________________________

Date purchased: _______________________________________________________________

Date installed:_________________________________________________________________

Location: ______________________________________________________________________

Input voltage/frequency:________________________________________________________

Output voltage/frequency: ______________________________________________________

Battery reserve time:___________________________________________________________

Image 2

Liebert 610 manual Battery Cabinet Precautions

Contents

Series 610 UPS Battery Cabinet Precautions Table of Contents Maintenance Specifications Figures Tables Important Safety Instructions System Description Other Factors to Consider ReliabilityDesigned for Success Safety Precautions Modes of Operation Operator Controls Options Battery Load Testing Customer Alarm InterfaceTemperature-Compensated Charging Automatic Restart UPS Module Battery PlantGeneral Component Descriptions Software Detailed Component DescriptionsControls Hardware Operation Input Power FactorRectifier/Charger Input Circuit Breaker Battery Charge Current Limiting Battery Charging CircuitBattery Disconnect Battery Equalize Charge Circuit Inverter Non-Linear Load CharacteristicsUnbalanced Load Characteristics Output Regulation and Overload Performance Bypass Circuit Breaker Static Switch Backfeed ProtectionStatic Bypass Pulsed Parallel Operation Transfer and Retransfer Conditions Three Breaker Maintenance Bypass Switchboard Features Display Screen and Operator Controls Operator controls, typical system 100kVA 500kVA 1000kVA Description Function Series 610 UPS operator control panel Description Function Menu Tree Navigation Menu tree Master Menu Screen Master menu screen Operation Output Metering Displays Monitor/Mimic Display ScreenInput Metering Displays Item 6 Status Messages Status/Alarm Message AreasItem 7 Alarm Messages Monitor/Mimic display example Utility fail Walk-In Display Screen Walk-in display screen Status Reports Screens Status reports screen Present Status Event History History Status History status report screen Battery Cycle Monitor System Status Battery cycle monitoring summary screen System Configuration Screens System configuration screens Maximum Auto-Retransfer Attempts Maximum auto-retransfer attempts screen Date Date screen Time Time screen Auto Dial Auto dial screen Language Selection System Options Continuous Duty Static Switch Optional Remote Monitor Alarm messagesAdditional alarm messages Standard Remote Monitor Indications Channel Battery Discharging Alarm Limit Settings ScreenOverload Alarm Low Battery Battery Rating Battery Shutdown 60 MinutesBattery Rating 100% Temperature Limit Setting Optional Load Transfer Procedures Screen Load transfer procedure screen Start-Up Procedures Screen Refer to 3.4.1 Start-Up Procedure for more details Shutdown Procedures Screen Battery Time Screen Battery time screen 15-minute discharge Upper Limit Actual Lower Limit Elapsed Time Minutes Meter Calibration Screen Status Reports Screens Battery Equalize Screen Battery equalize screen Alarm and Status Messages Status Messages Alarm and status message screen Alarm Messages Abbreviations used in alarm messages Alarm messages and corrective actions AC Input UPS System UPS System Cooling Alarm messages-summary Alarm Message Special Functions Auto-Dial Communication InterfacesWorldwide Reporting Site Reporting SiteScan or Snmp Local Reporting to a TerminalLocal Reporting to a Monitor Requesting Information Separate / Simultaneous Outputs Series 610 terminal commandsRemote Monitor Panel Keys Function Abbreviation Circuit Breaker Load on BypassCircuit breaker abbreviations OK to Transfer Load on bypass UPS available Load on UPS bypass available Momentary overload through pulse-parallel static switch Momentary Overloads Input Power Failure-Load on Battery Input power fail-load on battery Off Battery Load on UPS-battery not available Refer to 3.4.4 Shutdown Procedures Emergency Module Off Remote Emergency Power Off Emergency power off Refer to 3.3.9 Maintenance Bypass Module Shutdown Load on maintenance bypass two breakers Load on maintenance bypass three breakers Manual Procedures Start-Up Procedure Start-Up Procedure Set the Static Switch Disconnect or to OFF open Start-up procedures Start-Up Procedure Load Transfer Procedures Load transfer procedures screen Maintenance Bypass Load Transfers Shutdown Procedures Module Shutdown Procedure Shutdown Procedures Remote Emergency Power Off Repo Local Emergency Modules Off Lemo Battery Exercise Procedures Battery exercise control screen above and results below 1000% Automatic OperationsOverloads Without Transfer 150% Automatic Transfers to Bypass Overload Condition Automatic Retransfers to UPS Automatic Transfers to Bypass UPS System Faults Sequence of Operation Automatic Restart OptionalEnabling Automatic Restart Maintenance Professional Start-Up Liebert Global ServicesMaintenance Agreements The Signature Program Training Air Filters Routine MaintenanceRecord Log Limited Life Components Battery Maintenance Battery Safety Precautions Avertissement Matching Battery Cabinets Optional Number of Cells Battery Voltage VDC Nominal Float Rack-Mounted Batteries Battery retorque valuesBattery voltage record Torque Requirements Torque specifications unless otherwise labeledDetection of Trouble Corrective Actions Reporting a ProblemUpstream Feeder Circuit Breaker Setting Inspections Recommended Test Equipment KVA Power factor pf KVARating Specifications applicable to environment Environmental Conditions Adjustments Battery Operation Electrical Specifications Page Locations Technical Support/ServiceCompany Behind the Products United States