Delay | Lightwave Communications LDX-3232 instruction

C H A P T E R 4

COMMAND REFERENCE

LDX-3232 Device-Dependent Command Reference

LDX-3232 Device-Dependent Command Reference

The following pages contain a reference for the device-dependent commands of the LDX-3232 High Compliance Current Source. This reference contains useful information for both local and remote operation of the LDX-3232.

References to the front panel labels are capitalized in the following reference pages (as is done throughout this manual). Therefore, a reference to the LOCAL switch is meant to signify the actual switch labeled LOCAL on the front panel of the LDX-3232.

In some reference, parentheses are used to signify the labeled are for a particular switch or LED indicator on the front panel. For example, (PARAMETER) SET refers to the switch labeled “SET” in the PARAMETER area of the front panel.

DELAY

FRONT PANEL

REMOTE

The DELAY command causes the execution of commands to be delayed by a user- defined time. This command is similar to the *WAI common command, except that execution resumes after the specified number of miliseconds, instead of waiting for the Operation-Complete flag to be set.

Syntax Diagram

:DELAY

<white

space>

<nrf

value>

Parameters	An <nrf value> that represents the delay time in milliseconds.
Notes	The Operation-Complete flag is held false until the delay period elapses, but the *OPC?
	query will not execute until the delay period has elapsed.
	This command is useful for creating delays that don't require a lot of program code and
	don't tie up the GPIB during execution.
	The delay time is approximate, with an error of about ±10%.
Examples	"DELAY 500" -action: Further commands and queries are not executed until about 0.5
	seconds have elapsed from the time this command is executed.
	“LAS:LDI 22;Delay 2000;LAS:LDI?” -actions: The current is set to 22.0 mA, then the
	LDX-3232 High Compliance Current Source waits for about 2.0 seconds before returning
	the measured current.

Note: Care should be taken to set the GPIB time-out appropriately for use with the Delay command.

40 LDX-3232

Image 56

Lightwave Communications manual LDX-3232 Device-Dependent Command Reference, Delay

Contents

User’s Guide Page Table of Contents Remote Operation Command Reference Iv LDX-3232 List of Figures Vi LDX-3232 List of Tables Viii LDX-3232 Safety Information and the Manual General Safety Considerations Safety Symbols Safety Marking Symbols Warranty Claims for Shipping Damage Model Number Serial Number End-User Name Company Phone Fax Comments, Suggestions, and ProblemsDescription of the problem Xiv LDX-3232 Introduction and Specifications Product Overview Installing Your LDX-3232 High Compliance Current Source AC Line Power RequirementsInitial Inspection Grounding Requirements Gpib Connector Tilt-Foot AdjustmentGpib Address Operating the LDX-3232 Precision Current Source LDX-3232 Front View Maintenance Specifications 13 µs 12 ms Type Pulse Width DelayTTL Available Options and Accessories Description Model Number Applying Power to Your LDX-3232 Power On Sequence Connecting to the Laser Power On State Common Laser Cathode Photodiode Anode Back Panel LD Connector Interlock Connections Grounding Considerations Setting the PD BiasPhotodiode Connections Display Operating a Laser in Constant Current I ModeFront Panel Operation Setting Up the Precision Current Source E R a T I O N Operating a Laser in Constant Power P Mode Entering Photodiode Responsivity Values Method to calculate the responsivity is suggested below Error Indicators LDX-3232 Error Indicators Error Indicators LDX-3232 Reading the Gpib Address Changing the Gpib Address Changing Operation from Local to Remote LDX-3232 Current Source Command SetCommand Syntax OFF OLD NEW True False SET Reset LASLDI? Command Paths LDX-3232 Command Path Structure IEEE488.2 Command Commands LIM LDX-3232 Frequently Used CommandsNone Operation Complete Definition Status ReportingEvent and Condition Registers LDX-3232 Status Reporting Schematic Diagram Disabled 10 N/A Enabled 11 N/A 12 N/A 13 N/A 14 N/A 15 N/A Output Off Register LASerENABleOUTOFF nrf LASerENABleOUTOFF? Command Timing and Completion Error Messages Error Code Classifications Response Message Mode Used to create a delay in the execution of further CommandsUsed to enter the laser current calibration mode Used to enter the laser voltage calibration mode Returns status of photodiode monitor power display Enables Laser display to show parameter valuesSets the enable register for Laser conditions Returns the value of the LAS conditions enable register Used to return the optical power from monitor Used to set the constant optical power setpoint, ifUsed to enable/disable the front panel modulation input Or P optical power Returns the status of the Term command Powered upReturns the elapsed time since the timer was last reset Used to return the Laser setpoint tolerance value LDX-3232 Device-Dependent Commands Command Description Format LDX-3232 Device-Dependent Command Reference Delay Calmd LAS Calpd ERRors?LASerCALMD Responsivity CAL PD parameter setting Syntax Diagram LASerCALMD? Calibration for that bandwidth Selected. This procedure is outlined in ChapterLASerCALLDI LASerCALLDI? LASerCALLDVLDI LAS CAL LAS CAL LDV LASerCALMDI True measured value. This procedure is outlined in ChapterLASerCALLDV? LASerCALMDI? LASerCOND?MDI LAS CAL IPD LASerDEC LASerDISplay LASerDISplay?LAS DIS LASDIS? LASerDISplayLDI LASerDISplayLDI?Lasdisldi LDI Voltage measurement Syntax Diagram LASerDISplayLDVLASerDISplayLDV? LASDISLDV? LASerDISplayMDI LASerDISplayMDI?LAS DIS MDI LAS DIS IPD LASerDISplayMDP LASerDISplayMDP?PPD LAS DIS MDP LASerDISplayPARAM LASerDISplaySETLAS DIS Param LAS DIS SET LASDISPLAYSET? LASerENABleCONDLASerDISplaySET? LAS Enab Cond LASerENABleCOND?Bit LASerENABleEVEnt An nrf value whose sum represents the bits that are enabledAction enables the Laser status event register so that Lasenabevent LASerENABleEVEnt? LAS Enab EVE LASerENABleOUTOFF LASerENABleOUTOFF? LAS Enab Outoff LASerENABleEVEnt command Command while the condition status is constantly changingLASerEVEnt? LAS EVE LASerINC Function for the Laser output This measurement is updated approximately once every 600 ms LASerLDILASerLDI? LAS LDI LASerLDV LASerLDV?For LDV calibration LAS LDV LASerLIMitI2 LASerLIMitI2?Limit in use depends on the Laser output range selection LAS LIM Displayed, and then releasing the SET switch LASerLIMitI4LASerLIMitI4? LASLIMI4? MDP LAS LIM LASerLIMitMDPLASerLIMitMDP? LASerLIMitV LASerLIMitV? LASerMDI LASerMDI?MDI LAS IPD MDP P PD setpoint would be used LAS Mdln LASerMDLNLASerMDLN? MDP LAS LASerMDPLASerMDP? LAS Mode LAS Mode IhbwLASerMODE? LASerMODEIHBW LAS Mode MDP LASerMODEILBWLASerMODEMDP Lasmodeilbw LAS OUT LASerOUTputLASerOUTput? LASerRANge LASerRANge?LAS RAN LASRAN? Where the response is the constant I setpoint value, in mA 30 µA, for use in constant P mode with Calpd =LASerSETLDI? LASerSETMDI? Where the response is the constand PPD setpoint, in mW LASerSETMDP?LASerSTEP 100 µA LASerTOLerance command LASerSTEP?LASerTOLerance LAS TOL LASerTOLerance? MESsageSecond is the time window, in seconds MES MESsage? RADix Term 0 command is sent or the LDX-3232 is powered off RADix?RAD Means hexadecimal, and OCT means octal Time LDX-3232 was last powered upTime clock is independent of the Timer clock Since the last TIMER? query was issued TimerLast TIMER? query is returned Seconds since the last TIMER? query was issued Functions and Features Saving and Recalling from the Front Panel Using the Laser Compliance Voltage Adjustment Saving and Recalling Under Remote Operation Using the LDX-3232 Current Source’s Trigger Function LDX-3232 Rear Panel Modulating the Laser Current Source BNC Interlock Usage Example Modulating the Laser Current Source Functions and Features Calibration and Troubleshooting Calibration Overview DMM Description Manufacturer/Model SpecificationRecommended Equipment Local Calibration of the LDX-3232 Current Source Current Source CalibrationRange Current Limit IPD Current Calibration Constant power CAL PDSet equal to zero IPD Setpoint Laser Mode Laser Forward Voltage Measurement Calibration2000 mA Set to FS full scale of range Limit Gpib CommandRemote Calibration of the LDX-3232 Current Source Lasldi nrf value command IPD Setpoint Function State Gpib Command Troubleshooting Guide GeneralEEPROM, Lllll will be displayed on the display the laser Current source must be recalibrated Feature can be defeated via the Lasenableoutoff Command 101 Response Message