Status Indicator | Mitsubishi Electronics WD-62827 manual

Front Control Panel, continued

Status Indicator

Indicator Color	TV Condition	Additional Information

None (indicator off)	Normal TV on or standby condition.	Normal operation.

Yellow, steady	Room temperature is too high.	TV will not operate when the ambient room
		temperature is too high. Turn off the TV and wait
		until the room temperature drops.

Red, either steady or	TV may require service.	Turn off the TV and unplug the set from the AC power
blinking		source. Wait one minute and then plug the set back
		in.
		If the LED is still on, contact your dealer or a
		Mitsubishi Authorized Service Center. See
		www.mitsubishi-tv.com or call 1-800-332-2119 to
		receive Authorized Service Center information.

Power/Timer Indicator

Indicator Color	TV Condition		Additional Information

None (indicator off)	TV is powered OFF.		Normal operation.

Green, steady	TV is powered ON.		Normal operation.

Green, rapid blinking	1.	TV just plugged into AC outlet.	Wait until blinking stops before turning on
			(approximately 1 minute). Normal operation.
	2.	AC just restored after power	Wait until blinking stops before turning on
		failure.	(approximately 1 minute). Normal operation.

	3.	TV Rebooting after System Reset	Wait until blinking stops before turning on
		used.	(approximately 1-2 minutes). Normal operation.

	4.	TV Rebooting after power	Wait until blinking stops before turning on
		fluctuation or receiving abnormal	(approximately 1 minute). Normal operation.
		digital signals from digital channel,
		CableCARD™, or digital device.

	5.	You have begun the procedure	For detailed information, see the instructions
		to update software from an	that accompany the authorized software update.
		authorized flash memory device.	Important: Do not use non-authorized software at
			any time.

Green, slow blinking	TV powered off and automatic-on		Normal operation. TV can be turned on at any time.
	timer is set.

Chapter 1. Television Overview

15

Image 15

Mitsubishi Electronics WD-62827 manual Status Indicator, Power/Timer Indicator

Contents

TV Information Visit our website at TV Model Number Stand Model Number TV Guide On Screen Access RequirementsWhile Under Warranty After Warranty Stand Requirement FCC Declaration of Conformity Important Safeguards Important Safeguards Contents Mitsubishi DLP Projection Television Limited Warranty Mitsubishi Digital Electronics America, Inc Our Thanks Chapter TV Accessories Special Features of Your TV Widescreen Picture Format Memory Card ReaderTV Guide On Screen Interactive Program Guide System Memory Card Reader and Front-Panel Inputs Input 3 and Ieee 1394 Input/OutputCard Compatibility Reset Front-Panel Indicator Lights Lamp IndicatorFront Control Panel Power/Timer Indicator Status Indicator Overview Remote Control Battery Installation Sleep TimerCare . Component 1-3 Inputs IR Emitter NetCommandTV Back Panel Input 1 DTVLink/IEEE DVI Analog AudioHdmi 1 MonitorLink/RS-232C Control System Reset Button Additional InformationDemo Track Connecting Audio cables Connecting External Devices and NetCommand Setup Can be used with a CableCARD Connecting a Wall Outlet Cable or Cable BoxWall Outlet Cable Standard Cable Box For cable or antenna with coaxial lead Antenna with a Single LeadAntennas with Separate UHF and VHF Leads For antennas with flat twin leads $3CBDLQBOFM VCR to an Antenna or Wall Outlet Cable Audio & Video VCR to a Cable Box Audio & Video Connecting a VCR to a Cable Box Audio & Video Receiver Stereo System Satellite Receiver or Other Device with S-VideoTo connect an analog A/V receiver See Appendix a for component video signal DVD Player with Component VideoDVI Device Hdmi Device Hdtv Cable Box or Satellite Receiver with Component Video MonitorLink Control/RS-232C Device Connecting a MonitorLink Control/RS-232C Device TJFEEFWJDFT Connecting the IR Emitter NetCommand Direct Device-To-Device Style Connecting Compatible Ieee 139 Devices-Pin-Style vs -Pin-Style Connectors Connection Styles Digital Control Signal When Connecting Ieee 139 DevicesDigital Video Signals Digital Audio Signals Helpful Hints for NetCommand Connections NetCommand Setup and Editing NetCommand Introduction Receiver Using the Remote Control with NetCommandNetCommand Pre-Memorized Devices Receiver Cable Box SAT Satellite DVD Player NetCommand Setup On-Screen Buttons 3D Graphical Menu System Remote Control Buttons NetCommand Initial Setup NetCommand Information ScreenWelcome Screen Device Setup Screen Finish Screen NetCommand Initial Setup, Setup ReminderSetup Reminder Review Screen Edit NetCommand Adding an A/V Receiver Receiver ScreenReceiver Inputs Receiver AVR Learn Screen Receiver AVR Input Learn Screen Audio Output to AVR Screen Name Screen Edit NetCommand Adding Devices Edit NetCommand ScreenNew Device Screen Device Learn Screen Device Screen Connection for Device Screen Device Advanced Learn Screen VCR for Recordings Screen IR Code for Device ScreenRF Connection for Cable Screen Edit NetCommand Changing or Deleting Devices Change Device ScreenDelete Device Screen Ieee 1394 Devices and NetCommand Control Adding Ieee 1394 Devices Automatically Adding Ieee 1394 Devices AutomaticallyNew 1394 Device Screen Name for 1394 Device Screen Adding Ieee 139 Devices Automatically Ieee 139 Device Type ScreenConnection Screen Page NetCommand Functions Video Section Device Selection MenuPIP Device Selection Menu Audio Section IR Controlled Devices Using the Device Menu Button to Display MenusDevice Menu CableCARD Menu Guide and the Device Selection Menu Using the Guide Button to Display ChannelView and MenusGuide and the Recording Setup Screen Guide Button Record List NetCommand-Controlled RecordingsSetting up Recordings Time-Delayed Recording Copy-Protected Material Direct VCR Recording from an Antenna or Cable SourceTV Disc and A/V Disc Search by Time TV Disc and A/V Disc Track List Screen Using TV Disc and A/V Discs Using the Remote Control with TV Disc or an A/V DiscCopying or Moving TV Disc or A/V Disc Recordings Peer-to-Peer Connections What is a Peer-to-Peer Connection?Setting up a Non-Recording Peer-to- Peer Connection Cancelling a Peer-to-Peer Connection TV Menu Operations Main Menu Clock Setup MenuLanguage Memorize Channels Timer Lamp ReminderSoftware Version Icon Order NetCommand MenuRemote Control Transport Buttons Edit TV Pause Controlling TV Pause Features To Turn Off TimeShuttle TimeShuttleTV Pause with TimeShuttle TimeShuttle and TV Disc Recordings Record Recording SetupTime-Delayed Recording Record Menu Analog Recordings Default Digital Record DeviceCancel Scheduled Recordings TV Guide On Screen and the Record List Channel Menu SQV SuperQuickView Signal Strength Background Digital SettingsCaptions Menu Analog Captions Opacity Font FontsSize Color Chip Lock Menu Overview Setting a Pass CodeSetting V-Chip Options Chip Lock Menu Bypassing V‑Chip Lock and Lock by Time V-CHIP ButtonLock by Time Front Button Lock Chip Signal Information Content CategoriesChip Ratings Audio/Video Menu Digital-Only Audio Settings Audio SettingsAnalog and Digital Audio Settings Analog-Only Audio Settings Video Settings Video SettingsPC Video Settings Page CableCARD MediaCommand and Memory Card Playback Using a CableCARD CableCARDCableCARD Technology Memory Card Slots MediaCommand and Memory Card Playback For MP3 or WMA Audio Playlist Setup Media Command and Memory Card PlaybackMedia Setup Menu For Jpeg Picture Slide Show Setup Operation of PIP and POP Format Definitions Signal DefinitionsTV Display Formats DVD Definitions 57%JTQMBZ TV Disc or Digital Ieee 1394 Device On-Screen InformationAnalog Program Digital Program Using the TV with a PC Connecting a PC See Appendix a for signal compatibilityComputer with an Hdmi Monitor Output Computer with a DVI Monitor Output Computer with a 15-Pin Monitor OutputModels WD-62927 and WD-73927 Adjusting Image Resolution Adjusting Image Resolution PC Display Formats Page Appendix a Specifications Appendix F Cleaning and ServiceAppendix J Troubleshooting Appendix a Specifications TV SpecificationsInputs Outputs Appendix B NetCommand Specialized Device Keys Deactivating the Front Button Lock Appendix CBypassing the V-Chip Lock Bypassing the V-Chip Lock This page intentionally blank Cable Boxes Appendix D Remote Control Programming CodesProgramming the Remote to Control NetCommand A/V Products Receivers DVD Players Satellite Receivers/SAT/DTVVCRs DVD position TV positionCable/SAT/DTV position VCR position NetCommand Compatible Traditional Devices Analog Appendix E Device Control with NetCommand Ieee 1394 Devices When an Ieee 1394 Device is Viewed or Played Appendix F Cleaning and Service Do not touch the glass parts of the lamp cartridge Appendix G Lamp Cartridge Replacement Wash Your Hands THOROUGHLY, AS this Lamp Contains Mercury See detail Appendix H Diamond Shield Removal and Installation Raised Lip Channel Install TrimNotched edge Down TV Screen Pry up from the notches at both ends Install the Diamond ShieldStep Hook the top End over Raised lip Step Hook the lower End over Raised lip Appendix I Recording and Viewing Combinations Analog VCR Connected to Audio and Video Record OutputsDigital VCR or A/V Disc Connected to IEEE-1394 Port Appendix J Troubleshooting Symptom RemarksGeneral TV Operation PIP Picture Indicators Recording Sound Excessive digital artifacts when viewing an Ieee TV Guide On Screen Trademark and License Information Mitsubishi TV Software 123 Mitsubishi DLP Projection Television Limited Warranty 124 This Limited Warranty does not Cover Index Index Index Page Website Mail MDEAservice@mdea.com