Mitsubishi Electronics WD-62827 Computer with a DVI Monitor Output, Models WD-62927 and WD-73927

Connecting a PC

Computer with a DVI Monitor Output

Figure 2

ADVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable and audio cables are required. These are not included with the TV. They may be available at your local electronics retailer.

1.Connect the DVI-to-HDMI cable (recommended) (or DVI/HDMI adaptor with an HDMI cable) from the PC DVI output to HDMI 2 on the TV back panel.

NOTE: If you are using a DVI/HDMI adaptor, it is important to connect the adaptor to the DVI device for best performance.

2.Connect the L (left) and R (right) audio cables from AUDIO OUT on the PC back panel to INPUT/ DVI Analog Audio 2 on the TV back panel. If the computer’s audio output is a single mini-jack, a mini audio-to-RCA-male “Y” adaptor cable is needed to complete this connection.

NOTE: The HDMI connection supports copy protection (HDCP). Some devices require that you connect to an analog input first before you can view on-screen menus and select DVI as the ouput. Please review your equipment instructions for DVI connectivity and compatibility.

Computer with a 15-Pin Monitor Output

Models WD-62927 and WD-73927

Figure 3

A 15-pin PC monitor cable and stereo audio cables are required. These cables are not supplied.

1.Connect PC Monitor Out from the computer to PC INPUT on the TV back panel using a 15-pin PC monitor cable. See Appendix A for PC signal compatibility.

2.Connect the L (left) and R (right) audio cables from the computer to INPUT DVI Analog Audio 2 on the TV back panel. If the computer’s audio output is a single mini-jack, a mini audio-to-RCA-male “Y” adaptor cable is needed to complete this connection.

Note: To receive the benefits of a digital A/V receiver, connect your computer’s digital audio out, if available, to a digital input on your digital A/V receiver.

$PNQVUFS
XJUI
.POJUPS
0VUQVU





:

*/165

065165

%7*

"6%*0

3&$03%

&0

%7*

"OBMPH "VEJP

065165

065165

7*%&0

1C





0

1S

"OBMPH

"VEJP 

AUDIO-

(MONO)

LEFT/

0		"6%*0
		-&'5			"6%*0
0		.0/0
					3*()5
0		"6%*0
5		3*()5
		)%.* 	.0/*503-*/,™)%.*		1$ '03 )%.* 
			7*%&0 JQQJ 0/-:  )[
			"6%*0 1$. -*/&"3		7(" 87("
					47(" 847("
					9("  9 
(-JOL¸
*3 &.*55&3
/FU $PNNBOE¸
					.0/*503-*/,™
					$0/530-34$
%57$"#-&		57 #BDL 1BOFM
7)'6)'
64& 8*5)
$BCMF$"3%™		%*(*5"-				57
		"6%*0
"/5   "69	"/5   ."*/	065165
					*&&& 
					*/165
					065165
									1$ */165  )[
									7(" 87(" 47("
					J				847(" 9(" 89("
									 9   9 
%7*UP)%.*						:			065165
$BCMF
								%7*	"6%*0	3&$03%
								"VEJP	065165	065165
		1$ XJUI %7* 0VUQVU				1C		
										7*%&0
			"6%*0 065			1S				AUDIO-
										LEFT/
			-&'5			"6%*0				(MONO)
		$6) /54				-&'5				"6%*0
			3*()5			.0/0
										3*()5

Figure 2. Connecting a Computer with DVI Monitor Output Figure 3. Connecting a computer with monitor output.

IMPORTANT

•After connecting the PC, activate the PC option in NetCommand. Do this either during initial NetCommand setup (in the Device Setup screen), or at any time afterwards with the NetCommand Add function. See chapter 3.

•See Appendix A for signal compatibility.

CAUTION: To ensure continued FCC compliance, the user must use a shielded video interface or HDMI cable with bonded ferrite cores at both ends when using the PC input.

Chapter 7. Using the TV with a PC 93