Chapter 4 – Configuring Your MultiVOIP
| E&M Interface Parameter Definitions | |
|
|
|
Field Name | Values | Description |
|
|
|
Interface | E&M | Enables E&M features |
|
|
|
Type | I – V | Type of E&M interface being used – the individual types are detailed below. |
|
| Default = Type II. |
|
|
|
Mode | 2‐wire or 4‐wire | Each E&M interface type can be either 2‐wire or 4‐wire audio. |
|
|
|
Signal | Dial Tone or | When Dial Tone is selected, no wink is required on the E lead or M lead in |
| Wink | the call initiation or setup. |
|
| When Wink is selected, a wink is required during call setup. |
|
|
|
Wink Timer | 100 ‐ 350 | This is the length of the wink for wink signaling. Applicable only when Signal |
| milliseconds | parameter is set to “Wink.” |
|
|
|
No Response Timer | 1 – 65535 | The value here denotes the time (in seconds) after which the call attempt |
| (in seconds) | would be disconnected by the FXO Interface because there was no answer. |
|
|
|
Disconnect on Call | Y/N | Allows call on FXO port to be disconnected when a PBX issues a call‐progress |
Progress Tone |
| tone denoting that the phone station on the PBX that has been involved in |
|
| the call has been hung up |
|
|
|
Pass Through Enable | Y/N | When enabled (“Y”), this feature is used to create an open audio path for 2‐ |
|
| or 4‐wire. The E&M leads are passed through the VOIP transparently. |
|
| Applicable only for E&M Signaling with Dial Tone (not applicable for Wink |
|
| signaling). |
|
|
|
Dialing Options |
| |
|
|
|
Inter Digit Timer | 1 ‐ 10 seconds | This is the length of time that the MultiVOIP waits between digits. When the |
|
| time expires, the MultiVOIP looks in the phonebook for the number entered. |
|
| Default = 2. |
|
|
|
Message Waiting | Light or None | Allows MultiVOIP to pass mode‐code sequences between Avaya Magix PBXs |
Indication |
| to turn on and off the message‐waiting light on a PBX extension phone. |
|
| Mode codes: |
|
| *53 + PBX extension |
|
| Î turns message light on. |
|
| #53 + PBX extension |
|
| Î turns message light off. |
|
| Signals to turn message‐waiting lights on/off are not sent to phones |
|
| connected directly to the MultiVOIP on FXS channels, not to other non‐ |
|
| Avaya Magix PBX phone stations on the VOIP network |
|
|
|
Inter Digit | 50 – 20000 | The length of time between the outputting of DTMF digits. |
Regeneration Timer | milliseconds | Default = 100 ms. |
|
|
|
Flash Hook Options fields |
| |
|
|
|
Generation | 50 ‐ 1500 | Length of flash hook that is generated and sent out when the remote end |
| milliseconds | initiates a flash hook and it is regenerated locally. Default = 600 ms. |
|
|
|
Detection Range | for Min. and Max., | For a received flash hook to be regarded as such by the MultiVOIP, its |
| 50 ‐ 1500 | duration must fall between the minimum and maximum values given here. |
| milliseconds |
|
|
|
|
54 | MultiVOIP® Voice/Fax over IP Gateways |
