Network Technologies ASI-IP-GTW, DVB-ASI to IP

ASI-IP-GTW User's Manual

Page 91

Figure 41 SW load progress

When the file is transferred, a status message is printed in the main

browser window. If the loading was successful, the device is

automatically rebooted to start the new SW.

Figure 42 SW load status

Please remember to verify the new SW version on the ‘Device Info’ page

after the device has re-booted.

Contents

Main Page Important notice: About this manual How to use this manual Page Table of Contents Page Page 1 Introduction 1.1 Purpose of this Manual 1.1.1 Who Should Use this Manual 1.1.2 Warnings, Cautions and Notes 1.2 Contact Information 1.2.1 What Equipment is Covered by this Manual 1.2.2 Software versions 1.3 Role of the ASI-IP-GTW in a Typical System 1.4 Summary of Features Page 1.5 Guided Tour 1.5.1 The User Interface 1.5.2 Front Panel Description 1.5.3 Rear Panel Description 1.5.4 Construction 1.5.5 Hardware Options 1.5.6 Software Options 2 Installing the Equipment 2.1 Introduction 2.1.1 Read this first! 2.1.2 To inspect package content 2.2 Installing the Equipment 2.2.2 To fix the equipment 2.2.3 To cable the equipment 2.2.4 Equipment access 2.2.5 Ventilation 2.2.6 To connect the equipment 2.3 Power 2.3.1 AC Power Supply 2.3.2 Power Cable and Protective Earth Page 2.3.3 Optional DC Power Supply 2.4 Signal Connections 2.4.1 Introduction 2.4.2 ASI ports 2.4.3 Ethernet data port 2.4.4 Ethernet management port 2.5 LEDs 2.6 Powering Up/Down 2.6.1 Before Powering up 2.6.2 Powering Up 2.6.3 Powering Down 3 Operating the Equipment 3.1 Introduction 3.2 Changing the IP address of the unit 3.3 Looking at the WEB interface Page 27 To select a page, just click on the tab of the page you want to view. 3.4 Status 3.5 Device Info 3.5.1 Network Page Page 3.5.2 Time settings 3.5.3 Alarms 3.5.4 SNMP Page 3.5.5 Ping Page 3.5.6 Security 3.6 IP TX 3.6.1 Main Page Page 3.6.2 FEC Settings Page 3.6.3 Ethernet Settings 3.6.4 Ping Settings 3.7 IP RX 3.7.1 Main Page 3.7.2 FEC Settings Page 3.7.3 Ethernet Settings 3.7.4 Ping Settings 3.7.5 Advanced Tab Page 3.8 Network Page 3.9 Save/Load 3.9.1 Saving a Configuration 3.9.2 Loading a Configuration 4 Options 4.1 1PPS/10MHz interface modules 4.1.1 Separate 10MHz/1PPS module 4.1.2 1PPS interface 4.1.3 Operating the 1PPS/10MHz interface module 4.1.4 LED descriptions 4.2 RIPv2 functionality 4.2.1 User interface Page 5 Equipment Description 5.1 Introduction 5.2 Functional Description 5.2.1 Introduction 5.2.2 IP Transmit Mode 5.2.3 IP Receive Mode 5.2.4 IP Bi-directional Mode 5.2.5 Management 5.2.6 Alarms Page Page 5.3 Overview of Video over IP 5.3.1 Protocol mapping 5.4 Data Flow Block Diagrams 5.4.1 Forward Error Correction (FEC) Page 6 Preventive Maintenance and Fault-finding 6.1 Introduction 6.2 Preventive Maintenance 6.2.1 Routine Inspection 6.2.2 Cleaning 6.4 Fault-finding 6.4.1 Fault finding Philosophy 6.4.2 Preliminary Checks Page 72 6.4.3 PSU LED Unlit / Power Supply Problem If the ASI-IP-GTW PSU LED is unlit, fault-finding the problem is detailed in the following table. The PSU does not have any user changeable fuses. 6.4.4 Fan(s) Not Working / Overheating 6.4.5 Alarm LED lit / Alarm condition Page 74 The description of the severity levels of the different alarms are given in Section 5.2.6. 6.5 Disposing of this Equipment 6.5.1 General 6.6 To return the unit 7 Appendix A: Glossary Page Page Page 8 Appendix B: Technical Specification 8.1 DVB ASI port 8.2 Ethernet data port 8.3 Ethernet management port 8.4 Alarm relay and maintenance port specification 8.5 AC Mains Input 8.6 DC Mains input 8.7 Physical Details 8.8 Environmental Conditions 8.9 Compliance1 8.9.1 Safety 8.9.2 Electromagnetic Compatibility - EMC 8.9.3 CE Marking 8.9.4 Interface to public telecommunication system 9 Appendix C: References 10 Appendix D: Upgrade of Features Page Page 11 Appendix E: Upgrading Software Page 12 Appendix F: Quality of service Setting Packet priority 12.1 MPLS 12.2 Layer 3 Routing 12.3 Layer 2 priority