Network Technologies DVB-ASI to IP, ASI-IP-GTW specification

ASI-IP-GTW User's Manual

Metric on clear: The metric number to be used in the RIP messages when there are no active alarms in the unit.

Metric on critical: The metric number to be used in the RIP messages when there are at least one critical alarm present.

Destination: The IP destination address to use for the RIP messages.

Enable manual next hop: If set, the RIPv2 messages will specify the next hop as defined in the “Next hop address” field.

Next hop address: The address to be used for the next hop.

Route tag: Corresponds to the route tag field in the outgoing RIP messages.

Update interval: Specifies the average update interval for the RIPv2 messages. Note that the ASI-IP-GTW adds some random delay to avoid sending messages too regularly.

The status parameters are:

RIP-2 message count: Shows the number of RIP-2 messages transmitted.

Current metric: Shows the current metric used in the outgoing RIP-2 messages. Will be either the “Metric on clear” or the “Metric on critical” value.

Next hop: Shows the next hop value.

Page 62

Image 62

Network Technologies DVB-ASI to IP, ASI-IP-GTW user manual

Contents

DVB-ASI to IP Gateway This page is intentionally left blank Important notice Rev Date SW ver CommentPage Table of Contents Options 12.1 Who Should Use this Manual IntroductionPurpose of this Manual Contact Information What Equipment is Covered by this Manual Software versions Summary of FeaturesRole of the ASI-IP-GTW in a Typical System Page User Interface Indicator Colour DescriptionGuided Tour Front Panel Description Construction Hardware Options Software Options Functionality Max value Description Introduction Installing the EquipmentInstalling the Equipment To cable the equipment Equipment accessTo fix the equipment Ventilation To connect the equipment ASI port Power Cable and Protective Earth PowerAC Power Supply USA Nema 5-15P Protective Earth /Technical EarthUK BS Pin placement Specification Optional DC Power SupplyConnecting the Video Gateway to the AC Power Supply ASI ports Signal ConnectionsIntroduction DVB ASI output Ethernet data portDVB ASI input LEDs Ethernet management port Powering Up Powering Up/DownBefore Powering up Powering Down Operating the Equipment Changing the IP address of the unit Looking at the WEB interface Overall status Main tab Sub-tab Description Snmp Status Device Info Product type ASI-IP-GTW Network Main Advanced 1.22 SFP Device info page, Network and SFP sub-page Time settings Shows the sub-page for time setting used for alarm reports Alarms Snmp Snmp tab Ping Ping tabPage Shows the sub-page for user security password protection Security Main Input ConfigurationIP TX Input Status IP TX Parameters IP TX Status FEC Settings IP TX FECPage Static MAC setting Ethernet SettingsVlan settings Ping Settings Ping page of an IP transmitter Output Configuration IP RX IP RX Status Output StatusIP RX Parameters FEC sub-page of an IP receiver Page Ethernet sub-page of an IP receiver Ping page of an IP receiver Advanced Tab Advanced TabPage Transmitted Network streams NetworkData Network Interface Status Shows the Network page for a unit configured to IP-RX mode Received Network streams Saving a Configuration Save/Load Loading a Configuration Save/Load page when saving configuration Separate 10MHz/1PPS module Options1PPS/10MHz interface modules 2 1PPS interface Operating the 1PPS/10MHz interface module Shows the layout LED descriptions LED description for separate 1PPS/10MHz interface module RIPv2 functionality Shows the layout of the RIP-2 screenPage Functional Description IP Transmit ModeEquipment Description Management IP Receive ModeIP Bi-directional Mode Page Alarm Severity level Description Overview of Video over IP Protocol mapping UDP Mode Data Flow Block DiagramsForward Error Correction FEC Page Maintenance Preventive Maintenance and Fault-findingPreventive Maintenance Preliminary Checks Fault-findingFault finding Philosophy PSU LED Unlit / Power Supply Problem Step Action If the result of action is Yes Check Fan Alarm LED lit / Alarm conditionFans Not Working / Overheating Rotation Alarm Description Error source Progress Bitrate estimation General Disposing of this EquipmentTo return the unit Appendix a Glossary Page Page Page Appendix B Technical Specification DVB ASI port Ethernet management port Alarm relay and maintenance port specificationEthernet data port Protocols AC Mains Input DC Mains input Physical Details Compliance1 SafetyEnvironmental Conditions Electromagnetic Compatibility EMC CE Marking Interface to public telecommunication system Appendix C References Appendix D Upgrade of Features Ex. http//192.168.0.100/upgrade Feature upgrade Feature upgrade dialogue Upgrade SW Appendix E Upgrading Software SW load progress Layer 3 Routing Appendix F Quality of service Setting Packet priorityMpls ASI-IP-GTW Configuration Layer 2 priority