IP TX Status | Network Technologies ASI-IP-GTW, DVB-ASI to IP

ASI-IP-GTW User's Manual

Type of service (TOS): Enter Type of Service parameter as a byte value to be set in the Type-of-Service (TOS) field in the IP header as specified in RFC-791. This parameter is used for Class-of-Service prioritization. It depends on the Routers honouring this field. Please refer to “Appendix F: Quality of service – Setting Packet priority” for further details.

Time to Live (TTL): Enter Time to Live parameter as a byte value to be set in the Time to Live (TTL) field in the IP header as specified in RFC- 791.

Use multicast router: Click this box, to enable use of multicast router. The address of the multicast router is the same for the entire unit and is configured in the Network sub-page of the Device Info page. When this option is enabled, the MAC address used when configuring a multicast destination IP address, will be resolved to the IP address of the multicast router. If not using the multicast router option, multicast addresses automatically resolve to dedicated multicast MAC addresses.

1.1.1.26 IP TX Status

Resolved: Yes, when the MAC address of the configured IP destination address is resolved. The parameter is always yes, when multicast is used without using multicast router. No, when the MAC address is not yet resolved by ARP lookup.

Destination MAC address: Shows the destination MAC address used for the stream. This may be the MAC address of the receiving unit or the gateway if the receiving unit is on another network).

If using a multicast destination IP address without enabling multicast router, the field shows the multicast MAC address corresponding to the configured IP address. In the case of multicast router, the MAC address resolved for the multicast router is shown.

When the address is still not resolved this field displays the value 00:00:00:00:00:00.

Total bitrate: The bitrate of the IP frames containing this MPEG-2 transport stream and any FEC data related to this stream.

Data bitrate: The bitrate of the IP frames containing this MPEG-2 transport stream, excluding FEC information.

Page 41

Image 41

Network Technologies ASI-IP-GTW, DVB-ASI to IP user manual IP TX Status

Contents

DVB-ASI to IP Gateway This page is intentionally left blank Rev Date SW ver Comment Important noticePage Table of Contents Options 12.1 Who Should Use this Manual IntroductionPurpose of this Manual What Equipment is Covered by this Manual Contact Information Software versions Summary of FeaturesRole of the ASI-IP-GTW in a Typical System Page Guided Tour Indicator Colour DescriptionUser Interface Front Panel Description Hardware Options Construction Functionality Max value Description Software Options Introduction Installing the EquipmentInstalling the Equipment To fix the equipment Equipment accessTo cable the equipment Ventilation ASI port To connect the equipment Power Cable and Protective Earth PowerAC Power Supply USA Nema 5-15P Protective Earth /Technical EarthUK BS Pin placement Specification Optional DC Power SupplyConnecting the Video Gateway to the AC Power Supply ASI ports Signal ConnectionsIntroduction DVB ASI output Ethernet data portDVB ASI input Ethernet management port LEDs Before Powering up Powering Up/DownPowering Up Powering Down Changing the IP address of the unit Operating the Equipment Overall status Looking at the WEB interface Snmp Main tab Sub-tab Description Status Product type ASI-IP-GTW Device Info Main Network 1.22 SFP Advanced Device info page, Network and SFP sub-page Shows the sub-page for time setting used for alarm reports Time settings Snmp Alarms Snmp tab Ping tab PingPage Security Shows the sub-page for user security password protection Main Input ConfigurationIP TX IP TX Parameters Input Status IP TX Status IP TX FEC FEC SettingsPage Static MAC setting Ethernet SettingsVlan settings Ping page of an IP transmitter Ping Settings IP RX Output Configuration IP RX Status Output StatusIP RX Parameters FEC sub-page of an IP receiver Page Ethernet sub-page of an IP receiver Ping page of an IP receiver Advanced Tab Advanced TabPage Transmitted Network streams NetworkData Network Interface Status Received Network streams Shows the Network page for a unit configured to IP-RX mode Save/Load Saving a Configuration Save/Load page when saving configuration Loading a Configuration 1PPS/10MHz interface modules OptionsSeparate 10MHz/1PPS module 2 1PPS interface Shows the layout Operating the 1PPS/10MHz interface module LED description for separate 1PPS/10MHz interface module LED descriptions Shows the layout of the RIP-2 screen RIPv2 functionalityPage Functional Description IP Transmit ModeEquipment Description Management IP Receive ModeIP Bi-directional Mode Page Alarm Severity level Description Protocol mapping Overview of Video over IP UDP Mode Data Flow Block DiagramsForward Error Correction FEC Page Maintenance Preventive Maintenance and Fault-findingPreventive Maintenance Preliminary Checks Fault-findingFault finding Philosophy PSU LED Unlit / Power Supply Problem Fans Not Working / Overheating Alarm LED lit / Alarm conditionStep Action If the result of action is Yes Check Fan Rotation Progress Bitrate estimation Alarm Description Error source General Disposing of this EquipmentTo return the unit Appendix a Glossary Page Page Page DVB ASI port Appendix B Technical Specification Ethernet data port Alarm relay and maintenance port specificationEthernet management port Protocols DC Mains input AC Mains Input Physical Details Environmental Conditions SafetyCompliance1 Electromagnetic Compatibility EMC Interface to public telecommunication system CE Marking Appendix C References Ex. http//192.168.0.100/upgrade Appendix D Upgrade of Features Feature upgrade Feature upgrade dialogue Appendix E Upgrading Software Upgrade SW SW load progress Layer 3 Routing Appendix F Quality of service Setting Packet priorityMpls Layer 2 priority ASI-IP-GTW Configuration