Manuals / Nortel Networks / Communications / Answering Machine

Nortel Networks CalPilot 4.0 manual 201i Server Hardware Installation

Models: CalPilot 4.0

1 176

Download 176 pages 10.54 Kb

Specs Install See the following diagram Administration software Drain wire Diagnostics guide Secondary backplane connector Setting the modem DIP switches Switch Eligible slots

Page 1

201i Server Hardware Installation

CallPilot

Release 4.0

Document Number: 555-7101-220

Document Version: Standard 1.03

July 2006

Page 1 Page 2

Image 1

Nortel Networks CalPilot 4.0 manual 201i Server Hardware Installation

Page 1 Page 2

Related pages All Install page Can I customize amp settings for jazz in the CUBE-60? Find out

Contents

201i Server Hardware Installation Copyright 2006 Nortel Networks July Japan Vcci Statement Regulatory information Publication history Planning and Engineering CallPilot Customer Documentation Map Task List To connect the CD-ROM and tape drives to the 201i server Contents RoHS part conversion table 161 A p t e r Getting Help over the phone from a Nortel Solutions CenterGetting Help from the Nortel Web site Getting Help through a Nortel distributor or reseller This chapter About the 201i server Introduction 201i server descriptionRoHS compliance Primary components About the 201i server Following diagram shows the 201i server components Faceplate Following table describes each faceplate feature Diagnostics guide About the 201i serverStandard Temperatures Environmental specificationsRelative humidity Network connectivity Sample network setup Meridian 1 switch Web-enabled Desktop Administrative Client PC Telephony LAN/Customer LAN 10/100BaseT or 100BaseT Sample network setup Succession CallPilot Clan and Elan network setup Network requirements Multi I/O cable description Elan in the CallPilot Installation About the 201i serverStandard Faceplate connections Peripheral connectivityMonitor, keyboard, and mouse MPC-8 card Supported peripheral devicesScsi connections CD-ROM drive NTRH9105 Modem Tape drive NTRH903810Base-T Ethernet hub About the 201i server Preparing for installation Before you begin Installation overview CallPilot Installation and Configuration Task List Installation checklist Preparing for installationStandard Set the following Continue with the CallPilot switch model and CallPilot To unpack the 201i server Unpacking and inspecting the 201i server What to do if components are missing or damaged To inspect the 201i server for shipping damage What’s next? Meridian 1 or Succession 1000 slot requirements Switch and network requirements Clan and Elan network requirements Meridian 1 I/O panel connections To install the 201i server See Installing the 201i server in a large Meridian 1 system Overview Secondary backplane connector Scsi cables Backplane tip and ring cable Why you must move the connector Repositioning the secondary backplane connector Secondary backplane connector description Required equipment See the following diagram G101442 What’s next? To position the 201i server on the switch shelf Installing the 201i server in the large Meridian 1 switch Continue with Removing the backplane tip and ring cables on Removing the backplane tip and ring cables To remove the backplane cables If you attempt to pull the connector off without Continue with Installing the NTRH3501 backplane cable on Installing the NTRH3501 backplane cable To install the NTRH3501 backplane cable Continue with Installing the Scsi cables for Meridian 1 on Cables you need Installing the Scsi cables for Meridian What the completed installation looks like NTRH30AA To install the Scsi cables for Meridian Intermediate What’s next? Section a Installing Option 11C cables Switch Eligible slots G101559 G101588b What’s next? Standard This section Section a Installing Option 11C cables Cable description Installing the intermediate Scsi cable for Option 11C Option 11C Scsi cable NTRH1407 CD-ROM To install the cable Intermediate Scsi cable bracket assembly NTRH1407 G101555 What’s next? Section B Installing Option 11C Mini cables Installing the NTRH3502 Scsi cable for Option 11C Mini NTRH30AA To install the NTRH3502 Scsi cable Inner Scsi bracket If required, reinstall the Fiber Routing Guide Replace the cabinet cover To connect the cables Installing cables on the back of the Option 11C Mini cabinet Velcro Fastening Strap Pull to Tighten Drain wire Installing the 201i server in the Succession 1000 system Call Server Succession 1000 description Card slots Media Gateway and Media Gateway Expansion Media Gateway Not supported Not supported Media Gateway Expansion Back panel connectors One 10Base-T Ethernet connector that Yes Succession 1000 software Administration software Succession 1000 documentation To remove the front bezel and inside front cover plate Removing the Media Gateway or Media Gateway Expansion cover 201i Server Hardware Installation 103 Continue with Installing the 201i server on Installing the 201i server 106 CallPilot 201i Server Hardware Installation 107 CD-ROM and tape drive cabling diagram Installing the NTRH3502 Scsi cable for Succession To install the NTRH3502 cable 110 CallPilot 201i Server Hardware Installation 111 To replace the inside front cover plate Replacing the Media Gateway or Media Gateway Expansion cover 201i Server Hardware Installation 113 To replace the front bezel Connecting cables to the Succession 1000 system 116 CallPilot 201i Server Hardware Installation 117 118 CallPilot Preparing peripheral devices Supported Scsi devices DIP switches, Scsi ID, and Scsi device termination settings To set the modem DIP switches Setting the modem DIP switches Command mode local echo suppression To set the CD-ROM drive Scsi ID Setting the CD-ROM drive Scsi ID and DIP switches To set the CD-ROM drive DIP switches To set the tape drive Scsi ID Setting the tape drive Scsi ID 201i Server Hardware Installation 127 Supported daisy chain connection scenarios Setting Scsi device termination Meridian Option 11C, Option 11C Mini Succession To set device termination Preparing peripheral devicesStandard Connecting peripheral devices to the 201i server Connecting peripheral devices Connecting the 201i server to the networkMPC cards CD-ROM and tape drives 201i Server Hardware Installation 135 201i server faceplate and peripheral device connectors Starting the 201i server To install the MPCs Installing the MPCsCorrect card insertion Continue with Installing the monitor, keyboard, and mouse on Hardware requirement Installing the monitor, keyboard, and mouse PS/2 extension cable To connect the monitor, keyboard, and mouse Connecting the CD-ROM and tape drives Selecting the procedure for your switch NTRH30AA 201i Server Hardware Installation 145 CD-ROM 201i Server Hardware Installation 147 Tape drive 201i Server Hardware Installation 149 Connect the power cord for each device Power up the devices To establish the switch and network connections Connecting the 201i server to the switch, ELAN, and Clan 152 CallPilot Continue with Connecting the modem on To connect the modem Connecting the modem 201i Server Hardware Installation 155 Continue with Completing the installation on To complete the installation and start the 201i server Completing the installation 158 CallPilot 201i Server Hardware Installation 159 160 CallPilot RoHS part conversion table RoHS part conversion table RoHS part conversion table RoHS part conversion table cont’d NTDK57ACE6 166 CallPilot Numerics Index Index July Index 170 CallPilot Clan 172 CallPilot July Index 174 CallPilot Page 201i Server Hardware Installation

Top Page Image Contents