Warning System
Warning Description TablesIf a problem is detected immediately after the power is turned on, or during operation, this will be indicated by the WARNING lamp, lamps on the LCD monitor and a warning tone.
Warnings have priorities. If multiple errors occur simultaneously, the WARNING lamp, warning display on the screen, and alarm tone are displayed in order of priority shown in the table below.
| Warning |
|
| WARNING | Alarm | Warning description |
|
|
|
Priority | LCD indication | Tally lamp | and recording/playback | Countermeasures |
|
| |||
| type |
|
| lamp | tone*1 | operation |
|
|
|
|
|
| Blinks 4 | Blinks 4 |
| Reference signal or | Check the cause |
|
|
|
| SYSTEM ERROR cause | Continuous | indication *2 |
|
| |||
1 | System error | indication*2 blinks red. | times per | times per | tone | communication error. | and consult your |
|
|
|
|
| second | second |
| Operation stops. | distributor. |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| A P2 card was removed |
|
|
|
| Incorrect |
| Blinks 4 | Blinks 4 |
| during access and card data | Turn off the power. |
|
|
| TURN POWER OFF | Continuous | was corrupted. | Repair the P2 card if |
|
| |||
2 | P2 card | times per | times per |
| ChapterInspectionsand 9 | ||||
red, and the battery level |
| The battery is exhausted. | the clips on the card |
| |||||
| removal | Blinks red | second | second | tone | Both P2 card access LEDs |
|
| |
|
|
|
|
|
| blink in orange. Recording/ | are corrupted. |
|
|
|
|
|
|
|
| playback cannot start. |
|
|
|
|
| LOW BATTERY blinks |
|
|
|
|
|
|
|
| The | bar blinks with the empty | Blinks 1 time |
| Continuous | Recording and playback | Replace the battery. |
| Maintenance |
3 | battery is | status. (This indication | per second | Lights | tone | stop. The camera stops |
| ||
| exhauseted | appears even if CARD/ |
|
|
| automatically when the |
|
|
|
|
| BATT is set to OFF in the |
|
|
| voltage drops. |
|
|
|
|
| DISPLAY SETUP screen.) |
|
|
|
|
|
|
|
|
| VERSION MISMATCH | Blinks 4 | Blinks 4 |
| Version misatch has occurred. |
|
|
|
| Version |
| Only SD CARD FORMAT and | Perform CARD |
|
| |||
4 | PLEASE UPDATE | times per | times per | No |
|
| |||
mismatch | UPDATE are available with the | UPDATE. |
|
| |||||
| Blinks white | second | second |
|
|
| |||
|
|
| thumbnail menu. |
|
|
| |||
|
|
|
|
|
|
|
|
| |
| High |
|
|
|
| High temperature error | Stop operation |
|
|
|
|
|
|
| is detected. Operation |
|
| ||
| Temperature | HIGH TEMPERATURE |
|
|
| immediately |
|
| |
5 | Off | Off | No | continues, but abnormal |
|
| |||
error | Blinks red | and consult your |
|
| |||||
|
|
|
| recording/playback may |
|
| |||
| detectionl |
|
|
|
| distributor. |
|
| |
|
|
|
|
| occur. |
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| The fan is in failure and has |
|
|
|
|
|
|
|
|
| stopped. Although operation | Check the cause |
|
|
|
|
|
|
|
| continues with the fan |
|
| |
|
| FAN STOPPED cause |
|
|
| indication*3 and |
|
| |
6 | Fan stop | Off | Off | No | stopped, it may raise the |
|
| ||
indication*3 blinks red | consult your |
|
| ||||||
|
|
|
|
| temperature inside the unit, |
|
| ||
|
|
|
|
|
| distributor. |
|
| |
|
|
|
|
|
| causing abnormal recording/ |
|
| |
|
|
|
|
|
| playback. |
|
|
|
|
|
|
|
|
| (Continued on the next page) |
| ||
*1 When the alarm sounds, audio is not output to the camera speakers or earphones. The DISP/MODE CHK button cancels only the alarm tone when pressed during an alarm.
*2 P2 SYSTEM ERROR cause indication
•P2 MICON ERROR: The P2 microprocessor does not respond.
•P2 CONTROL ERROR: A P2 recording control error has occurred.
•CAM MICON ERROR: The camera microprocessor does not respond.
•P2 MICON LINK ERROR: A connection error between P2 microprocessors has occurred. *3 FAN STOPPED cause indication
•FAN: FAN error position (1, 1/2, 1/3, 2, 2/3, 3, 1/2/3)
127