Manuals / Brands / Computer Equipment / Projector / Panasonic / Computer Equipment / Projector

Panasonic PT-D10000E, PT-DW10000E Example of connecting with VIDEO devices

1 122

Download 122 pages, 26.47 Mb

ENGLISH – 25

Getting Started

Example of connecting with VIDEO devices

Attention

When connecting with a video deck, be sure to use the one with a built-in time base corrector (TBC) or use a

TBC between the projector and the video deck.

If nonstandard burst signals are connected, the image may be distorted. If this is the case, connect a TBC

between the projector and the video deck.

Note

The DVI-D signal input terminal supports only a single link.

The HDMI-DVI-D conversion cable is required to connect an HDMI-compliant device.

The EDID mode setting must be selected so that it corresponds to the device to be connected. (pp. 71, 72)

It is possible to connect the DVI-D input terminal with an HDMI- or DVI-D-compliant device, but with some

devices the images may not appear or other problems may be encountered in operation.

•

•

•

•

•

•

IN OUT

RS-232C IN RS-422 IN RS-422 OUT

SERIALREMOTE 1 REMOTE 2 IN

OUT

IN

SYNC/HD VD

B/PBG/YR/PR

S-VIDEO IN

VIDEO RGB 2 IN DVI-D IN

RGB 1 IN

LAN

Video deck (TBC built-in)

Control PC Control PC

Colour monitor Video deck (TBC built-in) High-vision video deck

Red (connected to PR terminal)

Blue (connected to PB terminal)

Green (connected to Y terminal)

DVD player with HDMI

(HDCP) terminal

Control PC

IN OUT

RS-232C IN RS-422 IN RS-422 OUT

SERIALREMOTE 1 REMOTE 2 IN

OUT

IN

SYNC/HD VD

B/PBG/YR/PR

S-VIDEO IN

VIDEO RGB 2 IN DVI-D IN

RGB 1 IN

LAN

Video deck (TBC built-in)

Control PC Control PC

Colour monitor Video deck (TBC built-in) High-vision video deck

Red (connected to PR terminal)

Blue (connected to PB terminal)

Green (connected to Y terminal)

DVD player with HDMI

(HDCP) terminal

Control PC

Contents

Main Dear Panasonic Customer: Basic OperationSpecial FeaturesInformation Contents IMPORTANT SAFETY NOTICE IMPORTANT: THE MOULDED PLUG (U.K. only) 6 ENGLISH Precautions with regard to safety WARNING Page Page Page Before Using 10 ENGLISH Accessories Caution when moving the projector Cautions regarding setup Notes on use To view clear images: Do not touch the surface of the projection lens with bare hand. Screen Lamp Location and function of each part Front Remote control unit SideTop Bottom 14 ENGLISH Projector Main Unit Front Location and function of each part (continued) Rear ControlsSide Location and function of each part (continued) Connection terminals Using the remote control unit Loading batteries 1. Open battery compartment lid. 2. Insert the batteries. 3. Close the battery compartment lid. 18 ENGLISH Using the remote control unit (continued) Setting projector ID number to remote control Using a wired remote control Installation 20 ENGLISH Installation (continued) Adjusting the feet Projection scheme Installation geometry Projection distances by the type of projection lenses (optional) Projection distances by the type of projection lenses (for PT-DW10000E) For the screen aspect ratio of 16:9 (Units: m) L : Projection distance SH : Effective screen height SW : Effective screen width Side View Projection distances by the type of projection lenses (for PT-D10000E) Installation (continued) For the screen aspect ratio of 4:3 (Units: m) For the screen aspect ratio of 16:9 (Units: m) Lens type Zoom lens Fixed-focus Calculation formulas for projection distance by lens types (for PT-DW10000E) Calculation formulas for projection distance by lens types (for PT-D10000E) Connection 24 ENGLISH Before starting connection The pin-out and signal names of the DVI-D IN terminal are shown in the diagram below. The pin-out and signal names of the S-VIDEO IN terminal are shown in the diagram below. Example of connecting with VIDEO devices 26 ENGLISH Connection (continued) Example of connecting with personal computers Installation of input module (optional) Installing the input module Types of the input modules (optional) Prepare beforehand an input module (optional) compatible with the input signals of the system. Module Module model No. Terminal Signal formats supported Procedure of installation 1. Remove the slot cover. 2. Insert the input module. 3. Fix the input module. 4. Register the input signal. 1. Remove the slot cover. Connecting signals to the input module 30 ENGLISH Connecting the signal to the SD-SDI input module Connecting the signal to the HD/SD-SDI input module 32 ENGLISH Connecting signals to the DVI-D input module How to install and remove the projection lens (optional) How to install the projection lens How to remove the projection lens 34 ENGLISH Projection Power indicator lamp Connecting the power cord Powering up the projector Making adjustment and selection 36 ENGLISH Powering off the projector How to adjust the lens How to adjust the focus, zoom and shift CAUTION: At the projector 1. Press LENS on the control panel on the main unit. 2. Presstoselectanitem and adjust it. 38 ENGLISH How to adjust the lens (continued) Adjustment range after lens position (optical shift) The ET-D75LE5 has a fixed focal point, and so shift adjustment cannot be carried out. Moving the projection lens position to the home position Automatic adjustment (AUTO SETUP) a 40 ENGLISH Registration of input signal data Registration of new data Renaming the registered signals 1. Presstoselectthe signal whose details are to be displayed. 4. Use to select the characters and numerals one by one, and press ENTER to set them. Clearing the data of registered signals 1. Presstoselectthe signal whose data is to be cleared. 2. Press DEFAULT. Sub memory How to register into sub memory 2. PresstoselecttheSUB MEMORY number stored in the SUB MEMORY LIST. Registration of input signal data (continued) Procedure to switch to sub memory 1. Pressonnormalscreen (menu is not displayed). 2. Presstoselectthe sub-memory signal to be switched in the SUB MEMORY LIST. How to erase sub memory Basic operations using the remote control 44 ENGLISH Remote control operation (continued) Automatic adjustment (AUTO SETUP) 1. Press AUTO SETUP on the remote control or the main unit. Turning on button illumination Changing the picture aspect ratio 1. Press ASPECT on the remote On-screen menus 46 ENGLISH MAIN MENU SUB MENU PICTURE (pp. 49-55) POSITION (pp. 56-59) ADVANCED MENU (pp. 60-65) SECURITY (pp. 99-101) OPTION1 (pp. 67-74) DISPLAY LANGUAGE (p. 66) 48 ENGLISH On-screen menus (continued) Using the menu screens 1. Press DEFAULT. 1. Press MENU. Adjusting the picture 50 ENGLISH Adjusting Contrast PresstoselectBRIGHTNESS. 1. This adjusts the contrast for picture colours. Adjusting Tint This adjusts skin tones in the pictures. 1. PresstoselectTINT. The TINT individual adjustment screen will be Adjusting the colour temperature 52 ENGLISH 8. Presstoadjustthelevel. 1. PresstoselectGAMMA. Gamma setting This switches the gamma mode. Noise reduction setting 63 (High) 262 (Intermediate) 1. PresstoselectNOISE REDUCTION. 2. PresstoswitchNOISE REDUCTION. The setting will change as follows each time 54 ENGLISH Registering the picture mode settings as presettings 1. Press ENTER. 2 PresstoselectOK. Setting the system format To display pictures complying with the sRGB standard RGB YPBPRRGB YPBPR Adjusting the position 56 ENGLISH Shift adjustment 3. 1. PresstoselectSHIFT. Adjusting the aspect ratio 1. PresstoselectASPECT. 2. PresstoswitchASPECT. 58 ENGLISH Adjusting the position (continued) Adjusting the zoom ratio 1. PresstoselectZOOM. 3. PresstoselectMODE. 4. PresstoswitchMODE. Keystone distortion correction 1. Presstoselect KEYSTONE. 3. Presstoadjustthe KEYSTONE. 60 ENGLISH Digital cinema reality How to use ADVANCED MENU Blanking adjustment 1. 3. PresstoselectBLANKING. 3. Presstoselectthedesired item for adjustment. 4. Presstoadjustblanking. 62 ENGLISH How to use ADVANCED MENU (continued) Adjusting the clamp position 1. PresstoselectCLAMP 3. Presstoadjust. 4. Presstospecifytheareato be adjusted. 14 13 11 10 64 ENGLISH How to use ADVANCED MENU (continued) 15 18 17 Raster position 1. PresstoselectRASTER 3. Presstoadjustthe position. PT-D10000E PT-DW10000E 4. Press MENU three times. Setting the DISPLAY LANGUAGE Changing the display language 1. Presstoselectthedesired language. 2. Press ENTER to establish your selection. Option1 settings Adjusting colour matching 1. PresstoselectCOLOR 2. PresstoswitchCOLOR 68 ENGLISH If 3COLORS or 7COLORS was selected in step 2. The MEASURED DATA screen will be displayed. 2. The COLOR MATCHING: 3COLORS or COLOR MATCHING: 7COLORS screen will Large Screen Correction 1. PresstoselectLARGE SCREEN CORRECTION. 2. PresstoswitchLARGE SCREEN CORRECTION. The setting will change as follows each time 70 ENGLISH Auto signal 1. PresstoselectAUTO SIGNAL. 2. PresstoswitchAUTO SIGNAL. Automatic adjustment (Only RGB input) Back Colour 1. PresstoselectBACK COLOR. 2. PresstoswitchBACK COLOR. DVI EDID 1. PresstoselectDVIEDID. 72 ENGLISH AUX DVI EDID (Only when the optional input module is installed) 1. PresstoselectAUXDVI EDID. 2. PresstoswitchAUXDVI EDID. P IN P Setting FUNC1 1. PresstoselectFUNC1. 2. PresstoswitchFUNC1. 74 ENGLISH Position of on-screen indications OFF ON The user can specify the position of the on-screen indications. 1. PresstoselectOSD Option2 settings 76 ENGLISH Installation Setting INSTALLATION. 3. Press MENU twice. Altitude Direction DIRECTION. Output resolution (PT-D10000E only) 1. PresstoselectOUTPUT 2. PresstoswitchOUTPUT 78 ENGLISH Lamp select 1. PresstoselectLAMP SELECT. 2. PresstoswitchLAMP SELECT. Lamp relay 5. Press 1. PresstoselectLAMP RELAY. 2. PresstoswitchLAMP RELAY. OFF 00:00 23:00 01:00 80 ENGLISH System information Displays the system information of the projector. 1. PresstoselectSYSTEM INFORMATION. The SYSTEM INFORMATION screen will be Setting the date and time 1. PresstoselectDATEAND TIME. 3. PresstoselectTIMEZONE. 4. PresstoswitchTIMEZONE. 5. PresstoselectADJUST CLOCK. 82 ENGLISH Setting the startup logo 1. PresstoselectSTARTUP LOGO. 2. PresstoswitchSTARTUP LOGO. Password Displaying the internal test pattern Test pattern 84 ENGLISH How to use network function Initial setting of network 1. Presstoselectitems,and press ENTER to change the setting. 2. PresstoselectSTORE, and press ENTER twice. Returning the network function setting back to the factory setting 1. PresstoselectSTORE. 2. Hold down DEFAULT for 3 seconds. 86 ENGLISH Network connections Name and function of network function parts Accessing from the Web browser 4. Press OK and the top page will appear. Password change page Basic control page Detail control page Monitor information page Error information page When [FAILED] has appeared for an item OK: Normal operation FAILED: Occurrence of trouble OK: Normal operation FAILED: Occurrence of trouble Parameter Description Parameter Description E-mail setup page E-mail setup page (continued) DNS server set up page Authentication server setting page Ping test page Contents of mail sent Mail with the contents shown below is sent when the E-mail settings have been established. Mail with the contents shown below is sent when an error has occurred. Adjust clock page Network config page Firmware update page 98 ENGLISH Using the PJLink protocol Supported commands The following table lists the PJLink protocol commands that can be used to control the projector. PJLink security authorization Command Control details Notes Setting the security 100 ENGLISH Setting the security (continued) PASSWORD. Changing the password PASSWORD CHANGE. Changing the text 1. PresstoselectTEXT CHANGE. The TEXT screen will be displayed. 3. Presstoselectthetext position,andpresstoselect the characters of the text. The text is now changed. Using the serial terminals 102 ENGLISH Examples of connection Communication conditions (Factory setting) For RS-232C For RS-422 Single projector Communication conditions (Factory setting) Plural projectors Pin assignments and signal names 104 ENGLISH Using the serial terminals (continued) Basic format Control commands Cable specifications Connecting to a PC For RS-232C When multiple projectors are connected Using the Remote 2 terminal 106 ENGLISH Example of a control panel layout Pin assignments and control Indication of monitor lamp LAMP 4 monitor (LAMP 4) LAMP 2 monitor (LAMP 2) LAMP 1 monitor (LAMP 1) LAMP 3 monitor (LAMP 3) Temperature monitor (TEMP) LAMP 4 monitor (LAMP 4) LAMP 2 monitor (LAMP 2) Cleaning and replacement of air filter Procedure of cleaning Page Replacement of lamp unit 110 ENGLISH Precautions on lamp unit replacement Timing of lamp unit replacement Indication after 1 800 hours Procedure of lamp unit replacement Notes when installing the ceiling mount bracket 112 ENGLISH Installation procedure Before asking for service Self-diagnosis display Self- diagnosis display Details Remedy Self- diagnosis display Details Remedy Specifications Model No. PT-D10000E PT-DW10000E Appendix 118 ENGLISH Compatible RGB/YPBPR/DVI-D Signals Display mode Number of displayed dots Scanning frequency Dot clock frequency (MHz) Format H (kHz) V (kHz) List of P IN P Subwindow Main window 120 ENGLISH Dimensions Outside dimensions Installation dimensions diagram Index A B C D Matsushita Electric Industrial Co., Ltd Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) For business users in the European Union Information on Disposal in other Countries outside the European Union