Procedure of lamp unit replacement | Panasonic PT-DW10000E instruction

Procedure of lamp unit replacement

1.Be sure to observe the procedure “Powering up the projector” (p. 35) and “Powering off the projector” (p. 36), remove the power plug and confirm that the surroundings of the lamp unit have cooled off.

2. Use a Phillips screwdriver toLamp unit cover screw loosen the lamp unit cover screw

at the rear of the projector until the screw turns freely.

3. Open the lamp unit cover and remove it from the projector.

Lamp unit cover

4.Use a Phillips screwdriver to loosen the three fixing screws for the lamp unit to be replaced until the screws turn freely. Hold the handle of the lamp unit and gently pull the lamp unit out from the projector.

CAUTION

The lamp unit and structural parts around the lamp unit will be hot immediately after the projector has been used.

You might get burned if you touch it while it is still hot.

	Fixing	Handle
	screws	Handle
	screws

Lamp unit 2

Lamp unit 3

Lamp unit 1

Lamp unit 4

5.Install the new lamp unit.

6.Use a Phillips screwdriver to securely tighten the 3 lamp unit fixing screws for each lamp unit.

7.Install and close the lamp unit cover, and then use a Phillips screwdriver to securely tighten the lamp unit cover screw.

Caution

•Firmly install the lamp unit and lamp unit cover. If not installed firmly, a protection circuit will function and the power will not be turned on.

Lamp unit cover screw

Lamp unit cover

Information

ENGLISH – 111

Image 111

Panasonic PT-DW10000E, PT-D10000E manual Procedure of lamp unit replacement, Lamp unit cover

Contents

Models No. PT-D10000E PT-DW10000E Dear Panasonic Customer Model number PT-D10000E/PT-DW10000ESerial number Contents Important Safety Notice Important the Moulded Plug U.K. only Getting StartedFuse Do not overload the wall outlet Precautions with regard to safetyDo not handle the power cord plug with wet hands Insert the power cord plug securely into the wall outlet Do not place liquid containers on top of the projector Insulate the battery using tape or similar before disposalDo not place the projector into water or let it become wet Do not disassemble the lamp unit Do not look into the lens while the projector is being used Use only the specified batteryAlways disconnect all cables before moving the projector Do not place any heavy objects on top of the projector Getting Started Accessories Before Using Screen MaintenanceDisposal To view clear images Remote control unit Location and function of each partFront Side Top Bottom Projector Main Unit RearLamp LAMP1, LAMP2, LAMP3, LAMP4 Side Controls Power Standby Connection terminals Using the remote control unit Effective range of remote control operationLoading batteries Using a wired remote control Setting projector ID number to remote control Examples of system expansion Installation Adjusting the feet Installation geometryProjection scheme Started GettingSide View Top View Installation Calculation formulas for projection distance by lens types Pin No Pin SignalConnection Before starting connection Control PC Video deck TBC built-in Example of connecting with Video devices Example of connecting with personal computers Control PC To 2nd projector Serial in terminalControl PC Types of the input modules optional Installation of input module optionalInstalling the input module Module Module model Terminal Signal formats supported Insert the input module Procedure of installationFix the input module Register the input signal Remove the slot cover High-vision DVI-D input module Connecting signals to the input moduleSignal Projector Business digital LAN terminal*1 Connecting the signal to the SD-SDI input moduleSD-SDI input module optional ET-MD77SD1 for 480i/576i LAN terminal *1 Connecting the signal to the HD/SD-SDI input moduleHD/SD-SDI input module optional ET-MD77SD3 for HD/SD DVI-D input module optional Connecting signals to the DVI-D input module Projection lens lock button How to install the projection lensHow to remove the projection lens Projection lens cover lock button Indicator Projector status Status Power indicator lampConnecting the power cord Installation # $ Powering up the projectorMaking adjustment and selection Press Power on Confirmation screen will appear Powering off the projector# Press Power Standby Press the marked side How to adjust the focus, zoom and shift How to adjust the lens Adjustment range after lens position optical shift Moving the projection lens position to the home positionModel number PT-D10000E PT-DW10000E Projection lens Automatic adjustment Auto Setup Press to display Registration of input signal dataRegistration of new data Press Enter Enter Clearing the data of registered signalsSub memory Basic Press to select the SUB Press on normal screenRestrictions Status function Switching the input signalBasic Operation Using the Shutter function On-screen display function Displaying the internal test pattern Automatic adjustmentUsing the FUNC1 button Turning on button illumination Press Aspect on the remote control Setting will change as follows each time Aspect is pressedChanging the picture aspect ratio Main Menu item On-screen menus Display Language p Test Pattern p Signal List pp Network ppPosition pp Advanced Menu pp Resetting to the factory default Using the menu screens Press to select Picture Adjusting the pictureSwitching the picture mode Press to switch Picture Adjusting Contrast Adjusting BrightnessAdjusting Colour Adjusting Tint Adjusting the colour temperatureTemp Sharpness setting Gamma settingSharpness Iris Noise reduction settingDynamic iris setting Reduction Selector Setting the system format Press to select Natural Press to select Color RGB1/RGB2/DVI-D terminal input signalsSRGB is only enable when RGB signals are being input Display the Picture screen. p Press to select Picture Press to select Shift Adjusting the positionShift adjustment Adjustment Press to select Aspect Adjusting the aspect ratioPress to switch Aspect Operation Interlocked Adjusting the zoom ratioClock phase adjustment Phase Keystone screen will be displayed Press to adjustKeystonedistortion correction Keystone Press to select Digital How to use Advanced MenuPress to switch Digital Digital cinema reality Press to select Total Blanking adjustmentPress to select Input Resolution Press to select Blanking Adjusting the clamp position Edge blending adjustmentBlending Adjust Delay Frame delayPress to select Frame Delay Press to switch Frame PT-DW10000E Press to adjust the position PT-D10000ERaster position Press to select Raster Position Display Language Setting the Display LanguageChanging the display language Press to select the desired language Press to switch Color Matching Option1 settingsAdjusting colour matching Basic Operation Special Features Matching using a colorimeter Adjusting the colour Press to select R, G, B or Cy, Mg, Ye, Wh Press Enter Press to switch LargeLarge Screen Correction Data Setup Auto signalAutomatic adjustment Only RGB input Signal Color Back Colour Edid Press to switch AUX DVIPress to switch P in P Press to select AUX DVI Setting FUNC1 Press to switch FUNC1Press to select FUNC1 Memory Position of on-screen indicationsOSD memory Position Press Menu twice Option2 settingsSetting a projector ID Projector ID Press to select Altitude Installation SettingInstallation Altitude Horizontal ResolutionDirection Press to select Output Select Press to switch LampLamp select Press to select Lamp RS-232C setting Lamp relayRelay System information Cleaning the air filter CleaningInformation Clock Setting the date and timePress to select Date Time Press to select Startup Setting the startup logoPassword Press to switch Startup Pattern Displaying the internal test patternTest pattern Cycle of displayed internal test patterns Initial setting of network function How to use network function Press to select Store Hold down Default for 3 seconds LAN LINK/ACT lamp green Network connectionsName and function of network function parts LAN terminal 10BASE-T/100BASE-TX Accessing from the Web browser Press OK and the top page will appear Password changeClick Change password Basic control Menu display Lens adjustment Test pattern displayDetail control Monitor information When Failed has appeared for an item Error information Mail setup English Numbers 0 9, period DNS server set upButton to update settingsFeatures Special Ping test Authentication server setting Contents of mail sent Network config Adjust clock Firmware update Command Control details Using the PJLink protocolSupported commands PJLink security authorization Displaying the security screen Setting the securitySetting the password Password Press to set the password Setting the textChanging the password Password Change Text screen will be displayed Changing the textPress to select Text Change Using the serial terminals Communication conditions Factory settingExamples of connection Sub 9-pin male Pin assignments and signal namesPin Signal Description No. name For RS-422 Accepted Control commandsCommand Function of command Remarks Basic format Cable specifications Projector Computer DTE Specifications1st 2nd RS-422 OUT Names of terminals Open H Short L Using the Remote 2 terminalExample of a control panel layout Pin assignments and control Indication of monitor lamp Lamp 1 monitor LampLamp 3 monitor Lamp Use a vacuum cleaner to remove any dust blockages Cleaning and replacement of air filterProcedure of cleaning Place the filter cleaning unit Install the brush cover so that it Indication after 1 800 hours Replacement of lamp unitPrecautions on lamp unit replacement Timing of lamp unit replacement Lamp unit cover Procedure of lamp unit replacement Installation procedure Eye bolt WireEye bolt No image appears on screen Symptoms Check pointPower does not turn on Remote control does not Self Details Remedy Diagnosis Display Self-diagnosis display FE1 Model No PT-D10000E PT-DW10000E Specifications RGB2 input Appendix Compatible RGB/YPBPR/DVI-D Signals Main window List of P in P Dimensions Outside dimensionsInstallation dimensions diagram Index Adjusting colour matching For business users in the European Union Trademark Acknowledgement